Instant Interrupts - Revisited

[Bruce]

Did you forget these?

INCLUDE "DT_INTS-14.bas"
INCLUDE "ReEnterPBP.bas"

[Ioannis]

No Bruce. They are in pbp directory and the project too.

It is not the first time I use these excellent routines.

That is why I post here. I am almost driving myself in the la-la land with this!

Ioannis

[Bruce]

Hi Ioannis,

Strange. It compiles fine for me. Tried it with the old & new versions of DT_INTS!

[ScaleRobotics]

Did you forget these?

INCLUDE "DT_INTS-14.bas"
INCLUDE "ReEnterPBP.bas"

Compiles here as well, but I do get the same errors IF I leave the above lines out of the code. Are you sure the include lines are in your water?

[Acetronics2]

Hi, Ioannis

Compiles fine adding ...

@ __CONFIG  _LVP_OFF & _BODEN_ON & _CP_ALL & _MCLR_OFF & _PWRTE_ON & _WDT_ON & _INTRC_IO

to the top of your code ...

and

'*****************************************************************************
'Includes
'*****************************************************************************

INCLUDE "DT_INTS-14.bas"
INCLUDE "ReEnterPBP.bas"

'-------------   INTERRUPTS SETUP   ---------------------
ASM
INT_LIST  macro;    IntSource,  Label,      Type,  ResetFlag?
    INT_Handler     TMR1_INT,   _timer,     PBP,    yes
    INT_Handler     RBC_INT,    _in_triger, PBP,    yes
    endm
    INT_CREATE            ; Creates the interrupt processor
ENDASM

just BEFORE the Interrupts setup ... ( why ??? good question !!!)

It DIDN'T Compile placed at the top of program ... that's it

- also think to uncomment Wsave, Wsave1 .... etc. in DT INTs listing ....



Alain

[Ioannis]

Alain, there is no problem here where the lines of includes are placed. Either on the very top or just before the macros... Are you sure about that?

Ioannis

[Acetronics2]

Alain, there is no problem here where the lines of includes are placed. Either on the very top or just before the macros... Are you sure about that?

Ioannis

Hi,

Yess .. I'm pretty sure !!!

I had an error raising ( Vars_Saved not defined ... but it was correctly defined in the listing ) .

but now I've also uncommented Wsaves and compiler has compiled fine once ... no more compiler errors appears, whatever line the "includes" are placed ...

a bit strange, but not the first strange thing I see with MCS ...

Alain

[Ioannis]

Have tried to compile from command line and it went OK?

Ioannis

[comwarrior]

I'm looking at a possible necessity to need to upgrade to PIC24's and above...
I use DT INST INT's with my PIC16's and PIC18's however it would be a royal pain to have to write my own interrupt system for PIC24's and above...

Is their any work being done on DT Ints at the moment?
Is their any plans for DT Int's?
Anyone working on DT int's in a team?

Thanks

[ScaleRobotics]

I used DT-INTS 1.10 on a 16f887

[ScaleRobotics]

Your code compiles here without errors. PBP 2.60A

[Ioannis]

DT-INTS version 1.00 or 1.10?

Ioannis

[ScaleRobotics]

Your code compiles here without errors. PBP 2.60A

To be clearer, your code in post 609 compiles using the code shown. I had not tried it with the IOC_INT, only with the code listed in post 609. I guess you meant that when you changed it to IOC, you got the errors.....

Sorry

Walter

[Ioannis]

Thanks all for the support.

Al.: We are testing the new DT-INTs version 1.10. Here as Darrel pointed out the wsave are set in the main program.

Darrel: You are correct in the Port change Interrupts. Ok, I have them corrected and the two errors went away. But no joy on Interrupts. It seems that they are never triggered.

The latest test code is this:

DEFINE OSC 4

@Line1 = _DEBUG_OFF & _LVP_OFF & _FCMEN_OFF & _IESO_OFF & _BOR_OFF
@Line2 = _CP_OFF & _MCLRE_ON & _PWRTE_ON & _WDT_ON & _XT_OSC

@ __CONFIG _CONFIG1, Line1 & Line2

@ __CONFIG _CONFIG2, _WRT_HALF & _BOR40V

OPTION_REG.0=1		'PSA0 PRESCALER SELECT 1:1 TO 1:256
OPTION_REG.1=1		'PSA1
OPTION_REG.2=1		'PSA2
OPTION_REG.3=1		'PRESCALER TO: 1->WDT, 0->TMR0
OPTION_REG.4=0		'T0SE SOURCE EDGE 1->H TO L, 0->L TO H
OPTION_REG.5=0		'T0CS 1->FROM RA4, 0->FROM INT. CLOCK
OPTION_REG.6=0		'INT EDGE SELECT 0->H TO L, 1->L TO H
OPTION_REG.7=0		'PULL UP 1->DISABLE, 0->ENABLE

adcon0=%01000000    '0 off
adcon1=$80'6 off (all digitals)
ansel=$01
anselh=$00

PORTA=%00000001:PORTB=%00010000:PORTC=%10000001:PORTD=0:PORTE=0

TRISC=$80:TRISD=0:TRISE=0

TRISA = %00000001

TRISB = %00010000

wsave   VAR BYTE    $20     SYSTEM      ' location for W if in bank0
;wsave   VAR BYTE    $70     SYSTEM      ' alternate save location for W 
                                         ' if using $70, comment wsave1-3
clear
INCLUDE "c:\projects\picdem2\DT_INTS-14.bas"
INCLUDE "c:\projects\picdem2\ReEnterPBP.bas"

'-------------   VARIABLES   ---------------------

code_in             var portb.4

'-------------   VARIABLES   ----------------------

t1con=%00000000         '65,535ms interrupt time base

clear
goto main

'-------------   INTERRUPTS SETUP   ---------------------

IOCB=%00010000          'Enable IOC on PortB.4
WPUB=%00010000          'Enable weak pull up on PortB.4

ASM
INT_LIST  macro;    IntSource,  Label,      Type,  ResetFlag?
    INT_Handler     RBC_INT,    _IOC2,      PBP,    yes
    endm
    INT_CREATE            ; Creates the interrupt processor
ENDASM

@   INT_ENABLE  RBC_INT      ; Enable Port B on change

'-------------   INTERRUPTS SETUP   ---------------------

IOC2:
    if code_in then
        high portb.0
    else
        low portb.0
    endif
@ INT_RETURN


main:
while 1
toggle portb.2
pause 100
wend

End

Ioannis