PIC USB to VB.NET

[jmgelba]

Thanks guys. I think I've found my issues.

One more question for now though, is the data within the byte transmitted msb first or lsb first from VB?

[gadelhas]

Thanks guys. I think I've found my issues.

One more question for now though, is the data within the byte transmitted msb first or lsb first from VB?

The answer to your question is in the code in post #1 and #2.

[Wirecut]

Hi.

I have tried to compile the source code that is present on the first page of this thread and I obtain the following error message:

Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 301 : Overwriting previous address contents (0000)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 301 : Overwriting previous address contents (0001)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 302 : Overwriting previous address contents (0000)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 302 : Overwriting previous address contents (0001)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 303 : Overwriting previous address contents (0002)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 303 : Overwriting previous address contents (0003)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 304 : Overwriting previous address contents (0002)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 304 : Overwriting previous address contents (0003)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 305 : Overwriting previous address contents (0004)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 305 : Overwriting previous address contents (0005)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 306 : Overwriting previous address contents (0006)
Error[118]   C:\PIC\MEL\PBP3061\18F4550\USB\PICUSB\PICUSB.ASM 306 : Overwriting previous address contents (0007)

the content of the file into the working directory is:

24/01/2011  02:45            22.213 DT_HID260.pbp
04/11/2009  11:41            28.721 DT_INTS-18.bas
04/04/2013  10:03             7.665 firmware.zip
04/04/2013  11:52            84.061 PICUSB.ASM
04/04/2013  11:52             1.368 PiCUSB.ERR
04/04/2013  11:52         1.112.440 PiCUSB.LST
04/04/2013  11:52            10.855 PICUSB.MAC
04/04/2013  11:52             4.917 PiCUSB.pbp
21/06/2012  03:06            96.199 usb_dev.asm
21/06/2012  03:06             6.290 usb_dev.inc
21/06/2012  03:06            26.203 usb_hid.asm
21/06/2012  03:06             6.378 usb_hid.inc
21/06/2012  03:06             6.403 usb_mem.asm

I'm using:
Win 7 Ultimate
A 18F4550 that will be run on the PICDEM FSUSB
PBP 3.0.6.1
MCS 5.0.0.3

I have the trial version (15 gg left - I'm waiting to solve some administrative trouble before buy the upgrade)

Attached please find the Directory contents.

Any suggestion will be more appreciate.

Ciao

Leo

[Demon]

Search for OVERWRITING, you get a ton of threads. Start with this one:

http://www.picbasic.co.uk/forum/show...ht=overwriting

Robert

[Wirecut]

Hi,

I have commented all of that:

;--- if you un-comment these, you must comment the ones in the .inc file ---
'ASM  ; 18F2550/4550, 8mhz crystal
' commented all to run , otherwize some error arise
'   __CONFIG    _CONFIG1L, _PLLDIV_2_1L & _CPUDIV_OSC1_PLL2_1L & _USBDIV_2_1L
'   __CONFIG    _CONFIG1H, _FOSC_HSPLL_HS_1H
'   __CONFIG    _CONFIG2L, _PWRT_ON_2L & _BOR_OFF_2L & _VREGEN_ON_2L
'   __CONFIG    _CONFIG2H, _WDT_ON_2H & _WDTPS_512_2H
'   __CONFIG    _CONFIG3H, _PBADEN_OFF_3H
'   __CONFIG    _CONFIG4L, _LVP_OFF_4L & _XINST_OFF_4L
'ENDASM

and all begin to work.

But there are some conceptual doubt that I have explained on a different thread:

http://www.picbasic.co.uk/forum/showthread.php?t=17877

[Wirecut]

Hi,

thanks to the suggestion of Henrik Ollson on the thread:

http://www.picbasic.co.uk/forum/show...740#post119740

I have substitute the ASM/ENDASM to #CONFIG/#ENDCONFIG as:

#CONFIG  ; 18F4550, 20mhz crystal 
   __CONFIG    _CONFIG1L, _PLLDIV_5_1L & _CPUDIV_OSC1_PLL2_1L & _USBDIV_2_1L
   __CONFIG    _CONFIG1H, _FOSC_HSPLL_HS_1H
   __CONFIG    _CONFIG2L, _PWRT_ON_2L & _BOR_OFF_2L & _VREGEN_ON_2L
   __CONFIG    _CONFIG2H, _WDT_ON_2H & _WDTPS_512_2H
   __CONFIG    _CONFIG3H, _PBADEN_OFF_3H
   __CONFIG    _CONFIG4L, _LVP_OFF_4L & _XINST_OFF_4L
#ENDCONFIG

and now "automagically" all works! GREATH!!!!

[nicjo]

Hi all,

I'm trying to use TMR0 however USB does not seem to communicate. I saw in past threads that TMR0 was used for USB polling, I've been examining all files related DT-INTS, DT-HID and soforth, TMR0 does not appear, so I don't know why using this timer would stop things. I'm not using DT-INTS on overflow just monitoring the int flag. By itsself i.e. no USB this little routine works fine. I'm outputing a 50msec (mark) pulse on portB then a second delay of around 300 msec (space). Goal is to adjust the space to vary stepper motor speed.

advice appreciated

Cheers

John

[nicjo]

Heres some of the code, this all works fine using simple delay or other timer

Main:
; Check for incomming USB data while waiting
@ ON_USBRX_GOSUB _HandleRX
lcdout $FE, 1, dec Size
pause 2000
if portB.0=1 OR Run=1 then
high porta.3
T0CON.7=1 'start TMR0
mark:
if not match01 then goto mark 'match01 var INTCON.2 '50msec delay
T0CON.7=0 'stop timer
match01=0 'clear interupt flag
INTCON.5=0 'set interupt enable to 0
low porta.3
if plugged then ARRAYWRITE USBTXBuffer, [Size,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0] ;send position
GOSUB WaitToSend
time=time+1
lcdout $FE, 1, dec time 'use to check whats happening here
TMR0H=$C9 '300msec
TMR0L=$10
T0CON.7=1 'start TMR0
space:
if not match01 then goto space
T0CON.7=0 'stop timer
match01=0 'clear interupt flag
INTCON.5=0 'set interupt enable to 0
TMR0H=$F6 '50msec pulse
TMR0L=$D8
endif
goto Main

[jmgelba]

Getting back to USB basics after a 3 year absence. I cant seem to get the code in the first post to run on a 18F2550. I get: ERROR Line 25: Bad BANK number. (DT_HID260.pbp) Apparently this issue didn't exist the first time I ran the code all that time ago.

Any pointers?