writing word variables to data memory

[Acetronics2]

Hi, Malc

Did you simply tried to Open the Holy Manual ???

supposing you use the PBP 2.60a Version ... it is at page 175 ...

supposing you use previous version ( 2.50b ) ... it is at page 162 ...

examples for WORDs given.

You also should have a look to $ 4.4 p 25 " Aliases " ... where it is shown how to " slice " your values ...

Alain

[malc-c]

Hi, Malc

Did you simply tried to Open the Holy Manual ???



Alain

http://www.picbasic.co.uk/forum/show...2176#post92176

Just don't quite understand it... (sorry I'm thick ! - care to actually explain how I would do this " Aliases " ... where it is shown how to " slice " your values thing ?)

[Acetronics2]

http://www.picbasic.co.uk/forum/show...2176#post92176

Just don't quite understand it... (sorry I'm thick ! - care to actually explain how I would do this " Aliases " ... where it is shown how to " slice " your values thing ?)

Ok Malc ...

let's make it easy :

The last PBP2.60 Version has introduced a Qualifier that permits you NOT to care with slicing your variables ...
so, if you own a v2.60 ( and You SHOULD ) ... the link you gave me becomes ... obsolete.

as you, NOW, just have to write:

WRITE Location, Word AlarmHigh[1] , Word AlarmHigh[2] , Word AlarmHigh[3] ,...

READ Location, Word AlarmHigh[1], Word AlarmHigh[2] , Word AlarmHigh[3], WA[1],WA[2],WA[3]

BUT remember a word need 2 EEPROM locations ... so,

WRITE Location +6 , Word AlarmHigh[4]
READ Location +6 , Word AlarmHigh[4] ,WA4

Alain

PS: of course, you can keep on using the " old method "

WRITE Location, AlarmHigh[1].Lowbyte
WRITE Location+1, AlarmHigh[1].Highbyte
WRITE Location+2, AlarmHigh[2].Lowbyte
WRITE Location+3, AlarmHigh[2].Highbyte
WRITE Location+4, AlarmHigh[3].Lowbyte
WRITE Location+5, AlarmHigh[3].Highbyte
WRITE Location+6, AlarmHigh[4].Lowbyte
WRITE Location+7, AlarmHigh[4].Highbyte

... but, is it really reasonnable ???

[malc-c]

The part I really find it hard to grasp is the WA[1], WA[2] bit and how to format the two eprom locations

So assuming the start address is 80

Could this then be changed to

For x = 0 to 3
For fn = 0 to 8
Write Word (80+fn) AlarmHigh[fx] highbyte
If fn >= 4 then 
x = 0 
Write Word (80+fn) AlarmHigh[fx] lowbyte
Next fn
Next x

I just can't seem to make this sink in !

[Acetronics2]

[QUOTE=malc-c;92222]

So assuming the start address is 80

Could this then be changed to

For x = 0 to 3
For fn = 0 to 8
Write Word (80+fn) AlarmHigh[fx] highbyte
If fn >= 4 then 
x = 0 
Write Word (80+fn) AlarmHigh[fx] lowbyte
Next fn
Next x

Oh my god ... you really thick ... ( YOU told it, not me ... )

following your explanation:

[code]

For fn = 0 to 3
Write (80+2*fn), Word AlarmHigh[fn+1]
next fn

[code]

LOCATION MUST BE PLACED BEFORE THE DATA !!!

( sorry for other users , but it's the 4 th time I repeat ... )


Business looks to have turned you deaf and blind ...

Alain

[malc-c]

This seems to compile

  for fn = 0 to 3
  write (10*fn + 80),lightsetHR[fn]
  write (10*fn + 82),lightsetMN[fn]
  write (10*fn + 84),lightoffHR[fn]
  write (10*fn + 86),lightoffMN[fn]
  write (10*fn + 88),word droptemp[fn]
  write (10*fn + 90),word normtemp[fn]
  write (10*fn + 92),StartHour[fn]
  write (10*fn + 94),StartMin[fn]
  write (10*fn + 96),StopHour[fn]
  write (10*fn + 98),StopMin[fn]
  write (10*fn + 100),word alarmhigh[fn]
  Write (10*fn + 102),word alarmlow[fn]
  next fn

[Acetronics2]

This seems to compile

  for fn = 0 to 3
  write (10*fn + 80),lightsetHR[fn]
  write (10*fn + 82),lightsetMN[fn]
  write (10*fn + 84),lightoffHR[fn]
  write (10*fn + 86),lightoffMN[fn]
  write (10*fn + 88),word droptemp[fn]
  write (10*fn + 90),word normtemp[fn]
  write (10*fn + 92),StartHour[fn]
  write (10*fn + 94),StartMin[fn]
  write (10*fn + 96),StopHour[fn]
  write (10*fn + 98),StopMin[fn]
  write (10*fn + 100),word alarmhigh[fn]
  Write (10*fn + 102),word alarmlow[fn]
  next fn

Malc,

Yes, It compiles BUT:

IF fn = 1 ...

@ location 110 & 111 you write AlarmHigh[1]

IF fn = 2

location 110 & 111 are overwritten by NormTemp[2]

IF fn = 3

location 110 is overwritten by lighsetHR[3]

and I only give you 3 examples ...

so, ... try

 
 write  80,lightsetHR[1]),lightsetMN[1],lightoffHR[1],lightoffMN[1],word droptemp[1] ,word normtemp[1],StartMin[1],StopHour[1],StopMin[1],word alarmhigh[1],StartHour[1],word alarmlow[1] ; need 16 locations
 
 write  100,lightsetHR[2]),lightsetMN[2],lightoffHR[2],lightoffMN[2],word droptemp[2] ,word normtemp[2],StartMin[2],StopHour[2],StopMin[2],word alarmhigh[2],StartHour[2],word alarmlow[2]
 
 write  120,lightsetHR[3]),lightsetMN[3],lightoffHR[3],lightoffMN[3],word droptemp[3] ,word normtemp[3],StartMin[3],StopHour[3],StopMin[3],word alarmhigh[3],StartHour[3],word alarmlow[3]
 
 
 write  140,lightsetHR[4]),lightsetMN[4],lightoffHR[4],lightoffMN[4],word droptemp[4] ,word normtemp[4],StartMin[4],StopHour[4],StopMin[4],word alarmhigh[4],StartHour[4],word alarmlow[4]

This Way, your EEPROM Map is neat ... and you know where to find What ...
...

What did you tell me by PM ???

I just call that pedagogics ...

Alain

[rsocor01]

This seems to compile

  for fn = 0 to 3
  write (10*fn + 80),lightsetHR[fn]
  write (10*fn + 82),lightsetMN[fn]
  write (10*fn + 84),lightoffHR[fn]
  write (10*fn + 86),lightoffMN[fn]
  write (10*fn + 88),word droptemp[fn]
  write (10*fn + 90),word normtemp[fn]
  write (10*fn + 92),StartHour[fn]
  write (10*fn + 94),StartMin[fn]
  write (10*fn + 96),StopHour[fn]
  write (10*fn + 98),StopMin[fn]
  write (10*fn + 100),word alarmhigh[fn]
  Write (10*fn + 102),word alarmlow[fn]
  next fn

Malcolm,

This code won't work anymore like Alain already mentioned. Now, you have words instead of bytes. Also, now you have 12 variables instead of 10 .

Now, if you try to write 12*2*4=96 bytes at location 80 then you are going to overwrite all the stuff that you wrote at location 150 with your DATA command (from your other post).

I would suggest that you should try first to clear up the mess by organizing the data that you put in EEPROM. It looks like the amount of data that you are putting in memory by doing "Data @0,0 and Data @150" is 58 bytes for each DATA command. So, instead of "Data @0,0 and Data @150" try something like "Data @0,0 and Data @58". Then from location 116 and up you have no data that could get overwritten.

Next, try the same code as above but with the following changes.

for fn = 0 to 3
  write (12*fn + 116),lightsetHR[fn]
  write (12*fn + 118),lightsetMN[fn]
  write (12*fn + 120),lightoffHR[fn]
  write (12*fn + 122),lightoffMN[fn]
  write (12*fn + 124),word droptemp[fn]
  write (12*fn + 126),word normtemp[fn]
  write (12*fn + 128),StartHour[fn]
  write (12*fn + 130),StartMin[fn]
  write (12*fn + 132),StopHour[fn]
  write (12*fn + 134),StopMin[fn]
  write (12*fn + 136),word alarmhigh[fn]
  write (12*fn + 138),word alarmlow[fn]
next fn

I replaced 10 by 12 since now you have 12 variables. I hope that this helps.

Robert