How to go forward?

[mackrackit]

The software that comes with PICKIT 1 only imports or exports a pre compiled hex file. So you will need MPLAB, but remember the PICKIT 1 will only work for a few chips (8 and 14 pins) so you may want to look at the PICKIT 2.

Here is a link to instructions to set PIC BASIC up with MPLAB.
http://www.melabs.com/support/mplab.htm

I agree with mister_e, get the PRO version of PIC BASIC if you can.

[Archangel]

Hello TheMadMan,
Cheap JDM programmers available on eBay, just search for JDM programmer, I saw one with a start bid of 99 cents US, that is all I have ever used, works great using I C Prog 1.05D available free on the web. Write some small programs, compile with demo PBP until you get a feel for what you want to do.

[TheMadMan]

Hi All
Thanks for the feedback!

<b><u>MicroCode Studio</u></b>
Downloaded and installed it and played around a bit. Seems a bit buggy in that gives strange errors.
&lt;Code&gt;<font color=blue><b>
x var byte
x = 1
SELECT CASE x
CASE 1
y = 10
CASE 2, 3
y = 20
CASE IS > 5
y = 100
CASE ELSE
y = 0
END SELECT
</b></font>&lt;/Code&gt;

Errors on the "SELECT CASE x" line.
Copied and pasted straight out of the manual document.

Also, does not give many of the most popular chips.
List of chips available from the dropdown list is
<font color=blue><b>
12C671, 12C672, 12CE673, 12CE674
14000, 14C000
16C554, 16C558
16C61, 16C62, 16C620, 16C620A, 16C621, 16C621A, 16C622, 16C622A, 16C62A, 16C62B, 16C63, 16C63A, 16C64, 16C642, 16C64A, 16C65, 16C65A, 16C65B, 16C66, 16C662, 16C67
16C71, 16C710, 16C711, 16C712, 16C715, 16C716, 16C717, 16C72, 16C72A, 16C73, 16C73A, 16C73B, 16C74, 16C74A, 16C74B, 16C76, 16C77, 16C770, 16C771, 16C773, 16C774
16C84
16C923, 16C924
16CE623, 16CE624, 16CE625
16F627, 16F628
16F73, 16F74, 16F76, 16F77
16F83, 16F84, 16F84A, 16F870, 16F871, 16F872, 16F873, 16F874, 16F876, 16F877
17C42A, 17C43, 17C44
17C752, 17C756, 17C756A, 17C762, 17C766
18C242, 18C252
18C442, 18C452
18C658, 18C858
PS1, PS1_2K, PS2, PS2_2K, PS3, PS3_2K, PS4, PS4_2K</b></font>

Maybe it was a faulty install or something, has anyone else had similar problems?

... but remember the PICKIT 1 will only work for a few chips (8 and 14 pins)

I've heard that if you make up a 14 pin to 40 pin adapter board you can use the PICKit 1 to burn the 40 pin range. Is this true? If so, does anyone have the pin connections?

Cheap JDM programmers available on eBay, just search for JDM programmer, I saw one with a start bid of 99 cents US, ...

Looks like a nice unit - fancy chip holder - US$49.00 + postage is a bit steep when you are not in America and not earning US$.
Found the circuit for the JDM Programmer (evidently done by Ludipino) at http://www.geocities.com/CapeCanaver...6/ludipipo.zip . Very low component count. 1 zener, 1 diode, 1 cap, 4 resistors, serial plug and ic socket. See it uses the fancy one - maybe thats the big price item.
There is a warning that it doesnt like laptops and must be plugged directly into the com port.

Found his site at http://www.jdm.homepage.dk/newpic.htm

Question: looks like the programmer puts the incoming signal into pins 12 and 13. If I use these pins as input/output in my app/board, wont the signals be "programmed" into the PIC?

works great using I C Prog 1.05D available free on the web.

Site at http://www.ic-prog.com - now at version 1.05F.
(All that raw machine code is frightening!)

...compile with demo PBP until you get a feel for what you want to do.

Just how "cut down" is the demo compiler version?
I do have access to a legal installation of PBP.

Thanks to all for the feedback so far. I'm certain I will have many more "idiotic" questions but I'll keep them for later.

All the best

[Bruce]

Where is Y declared?

x var byte
y var byte
x = 1
y = 0
SELECT CASE x
  CASE 1
   y = 10
  CASE 2, 3
   y = 20
  CASE IS > 5
   y = 100
  CASE ELSE
   y = 0
  END SELECT

Does this compile without errors?

[mister_e]

PICKIT 1 is a ICSP programmer (In Circuit Serial Programming), it only use the PIC dedicated pin to program them. In each and every datasheet you'll find the information. Those you'll need

MCLR/Vpp
Vss
PGD
PGC

Refer to PicKit 1 manual
http://ww1.microchip.com/downloads/e...Doc/40051D.pdf

page 41.

As long your device is in the Pickit 1 list, you should be able to program it. Now, how's the support now for this one since Pickit 2 is on the market? i don't know.

[TheMadMan]

MCLR/Vpp
Vss
PGD
PGC

Handy information

As long your device is in the Pickit 1 list, you should be able to program it. Now, how's the support now for this one since Pickit 2 is on the market? i don't know.

Dont think the 16pin and larger will be there.
Seems like using the PICKit 1 for anything bigger than 14 pins (and older generation types) is a non-starter.

I'll have a look for a generic ICSP board circuit and make up the necessary adapters as I go.
Maybe take the the "Ludipino JDM Programmer" circuit, make the necessary mods and build one for each pin configuration as I need it. There cant be <B>THAT</B> many variations can there.

Dont think that Microchip are idiots. All chips in each pin-count range probably have PGD and
PGC placed on the same pin.

Having said that, I'll probably choose the chip that is the exception to the rule at some time or another and make some smoke.

Thanks for the input mister_e.

All the best.

PS. Like the play on your name on your home page. ;>)

[TheMadMan]

Dont think that Microchip are idiots. All chips in each pin-count range probably have PGD and PGC placed on the same pin.

I see that Microchip dont make any reference to the programing pins in pin reference drawing at the top of the document.
You have to dig for it further down in the detailed list of each pin's functions.
If (like me) you dont really know what you are looking for, you may miss it (as I did).
Oh Well, live and learn.

[TheMadMan]

Where is Y declared?

OOPS!!!
Red Face Moment.
Bit pressed for time right now (5:06am local). Will give it a try.
Thanks.