SOLVED - Can't get IOC on pin change working

[Demon]

IOC on pin C4 now works after using custom INCLUDE DT_INTS-14_16F1885x-7x.bas:

;---[16F1885x7x]------------------------------------------------------------
; #define IOC_INT      INTCON,IOCIF, INTCON,IOCIE  ;-- Int On Change
  #define IOC_INT      PIR0,IOCIF, PIE0,IOCIE      ;-- Int On Change       *

I need to do more testing to confirm this was all I needed, but at least it picks up the positive edge change on the pin and lights InterruptLED.


EDIT: Complete code:

#CONFIG
    __config _CONFIG1, _FEXTOSC_OFF & _RSTOSC_HFINT32 & _CLKOUTEN_OFF & _CSWEN_OFF & _FCMEN_ON
    __config _CONFIG2, _MCLRE_ON & _PWRTE_OFF & _LPBOREN_OFF & _BOREN_ON & _BORV_LO & _ZCD_OFF & _PPS1WAY_OFF & _STVREN_ON & _DEBUG_OFF
    __config _CONFIG3, _WDTCPS_WDTCPS_11 & _WDTE_ON & _WDTCWS_WDTCWS_7 & _WDTCCS_LFINTOSC
    __config _CONFIG4, _WRT_OFF & _SCANE_available & _LVP_OFF
    __config _CONFIG5, _CP_OFF & _CPD_OFF
#ENDCONFIG

DEFINE OSC 32

include     "C:\PBP Includes\DT_INTS-14_16F1885x-7x.bas"
include     "C:\PBP Includes\ReEnterPBP.bas"

ASM
INT_LIST  macro      ;IntSource,  Label,     Type, ResetFlag? 
        INT_Handler   IOC_INT,    _MyIOCinterrupts,    PBP,  yes
    endm
    INT_CREATE                      ;Creates the interrupt processor
ENDASM

'--------------------------------------------------------------------------
'                           Controlled by DT-INTS
'INTCON = %10000000
'           bit 7   GIE         Global Interrupt Enable bit
'                                   1 = Enables all active interrupts
'           bit 6   PEIE        Peripheral Interrupt Enable bit
'           bit 5-1     Unimplemented: Read as ‘0’
'           bit 0   INTEDG      Interrupt Edge Select bit
'PIE0 = %00010000    ' PERIPHERAL INTERRUPT ENABLE REGISTER 0
'           bit 7-6 Unimplemented: Read as ‘0’
'           bit 5 TMR0IE: TMR0 Overflow Interrupt Enable bit
'           bit 4 IOCIE: Interrupt-on-Change Interrupt Enable bit
'                                   1 = Enables the IOC change interrupt
'           bit 3-1 Unimplemented: Read as ‘0’
'           bit 0 INTE: INT External Interrupt Flag bit
'--------------------------------------------------------------------------

IOCCP = %00010000   ' INTERRUPT-ON-CHANGE PORTC POSITIVE EDGE REGISTER
'           bit 7-0 IOCCP<7:0>  Interrupt-on-Change PORTC Positive Edge Enable bits
'                                   1 = Interrupt-on-Change enabled on the pin
'                                       for a positive-going edge. IOCCFx bit
'                                       and IOCIF flag will be set upon detecting an edge.

IOCCN = %00000000   ' INTERRUPT-ON-CHANGE PORTC NEGATIVE EDGE REGISTER
'           bit 7-0 IOCCP<7:0>  Interrupt-on-Change PORTC Negative Edge Enable bits
'                                   1 = Interrupt-on-Change enabled on the pin
'                                       for a Negative-going edge. IOCCFx bit
'                                       and IOCIF flag will be set upon detecting an edge.

ANSELA = %00000000
ANSELB = %00000000
ANSELC = %00000000
ANSELD = %00000000
ANSELE = %00000000

TRISA = %00000000
TRISB = %00000000
TRISC = %00010000
TRISD = %00000000
TRISE = %00000000

PushSwitch      VAR PortC.4
InterruptLED    VAR LatC.2

ButtonWasPressed VAR byte

    Pause 500                                       ' Let PIC stabilize
    InterruptLED = 0
    ButtonWasPressed = 0
    
@ INT_ENABLE IOC_INT

    IOCCF.4 = 0

Mainloop:

    if ButtonWasPressed = 1 then                    ' Check flag
        InterruptLED = 1
    endif
    
    goto mainloop

MyIOCinterrupts:

    if IOCCF.4 = 1 then
        ButtonWasPressed = 1                        ' set a flag
        IOCCF.4 = 0
'        INTCON.7 = 1        ' 7.1 Operation p. 129
                        ' The following events happen when an interrupt event
                        ' occurs while the GIE bit is set:
                        '   ...
                        '   • GIE bit is cleared
                        '   ...
    endif
@ INT_RETURN
end