Pic16f57 + lcdout=error

**pedja089** · - 6th October 2010, 19:55

When I try to compile I get this:

Code:

ERROR: Macro LCDOUTCOUNT?C not found in macro file.
ERROR: Macro LCDOUTNUM?W not found in macro file.
ERROR: Macro LCDOUTDEC? not found in macro file.

All Done, PCB, soldering. Project must be finished tomorow

Does anybody know why this happens and how to solve this problem?
I'm using PBP 2.60A & MCS 4.0
Is there any hope for this project to be completed on time?

**ScaleRobotics** · - 6th October 2010, 20:36

Can you give any more information? I put a simple lcdout command in pbp 2.60a for a 16F57 (MCS 3.0.0.5), and just got a crossing page boundary warning. No errors.

There is always hope.....

**pedja089** · - 6th October 2010, 21:48

Yes of course.
All comments are in Serbian.
Programm:

Code:

'@ DEVICE XT_OSC,WDT_OFF,PROTECT_ON
'DEFINE LCD_BITS 4
'DEFINE LCD_DREG PORTB
'DEFINE LCD_DBIT 0
'DEFINE LCD_RSREG PORTB
'DEFINE LCD_RSBIT 4
'DEFINE LCD_EREG PORTB
'DEFINE LCD_EBIT 5
'DEFINE LCD_LINES 2

DEFINE LCD_BITS 4
DEFINE LCD_DREG PORTB
DEFINE LCD_DBIT 0
DEFINE LCD_RSREG PORTA
DEFINE LCD_RSBIT 2
DEFINE LCD_EREG PORTA
DEFINE LCD_EBIT 3
DEFINE LCD_LINES 2    
    Tz var word
    Tt Var Word         
    Set var byte        
    Ton var byte
    Toff var byte
    Mode var byte
 
    CR Var Byte         
         
    
    Sn var byte
    Ss var byte
    
    Znak1 var byte
    Znak2 var byte
    Znak3 var byte
    Znak4 var byte

    I var byte
    
    symbol DQ = portb.4          
    symbol Tmode= portb.5
    symbol Tp=portb.6
    symbol Tm=portb.7
    symbol Rele=porta.1
    
    SYMBOL SCL = portc.4     
    SYMBOL SDA = portc.5
    
    input tmode
    input tp
    input tm
    output rele
    'adcon1=7
    clear
ss = tm         
rele=0
set=0
i=0
pause 100
lcdout $fe,1, " ....."
Lcdout $fe, $C0," www.....hr"
pause 2000
I2Cread SDA,SCL,$A0,0,[tz.lowbyte,tz.highbyte,toff,ton]
if tz>600 then tz=200
if toff=>100 then toff=5
if ton=>100 or ton=0 then ton=5

Pocetak:
sn = tmode
 if sn<ss then  set= set + 1
    
  if set>3 then 
   set = 0
  endif 
       
ss=sn
select case set
    CASE 0
     znak1=" "
     znak2=" "     
     znak3=" "
     call izmeri
     i=0  
    
    CASE 1 
     znak1=">"
     znak2=" " 
     znak3=" "
     if tp=0 and tz<600 then 
      tz=tz+5
      i=0
     endif 
     if tm=0 and tz=>5 then 
      tz=tz-5 
      i=0  
     endif
      I2CWrite SDA,SCL,$A0,0,[tz.lowbyte,tz.highbyte]
    
    CASE 2
     znak1=" "
     znak2=">"
     znak3=" "
     if tp=0 and ton<100 then 
      ton=ton+5
      i=0
     endif 
     if tm=0 and ton=>5 then 
      ton=ton-5
      if Ton=0 and toff=0 then ton=5
      i=0  
     endif
     I2CWrite SDA,SCL,$A0,3,[ton]
     
    CASE 3 
     znak1=" "
     znak2=" " 
     znak3=">"
     if tp=0 and toff<100 then 
      toff=toff+5
      i=0
     endif 
     if tm=0 and toff=>5 then
      toff=toff-5 
      if Ton=0 and toff=0 then toff=5
      i=0  
     endif
     I2CWrite SDA,SCL,$A0,2,[toff]
     
END SELECT 

 if tz+ton<=tt and set=0 and znak4="+" then 'ako je zadata temp manja od trenutne 
  rele=1                    'ukljuci rele
 endif                      
 if (tz=>toff and tz-toff=>tt and znak4="+") or (tz<toff and toff-tz<=tt and znak4="-" ) or set>0 then             'ako je zadata temperatura veca od trenutne ili si usao u meni
  rele=0
 endif
 
   
 i=i+1
 if i >100 then set = 4 'izadji iz menija

call prikazi
pause 150
goto pocetak





Prikazi:           
       Lcdout $fe,1,znak1,"+",DEC2 (tz / 10), ".",#(tz dig 0),223, "C"
       if set=0 then lcdout $fe,$89,znak4,DEC2 (tt / 10), ".",#(tt dig 0) ,223, "C" '178
       Lcdout $fe, $C0, znak2,"+",DEC2 (ton / 10), ".",#(ton dig 0),223, "C",znak3,"-",DEC2 (toff / 10), ".",#(toff dig 0),223, "C"        
return

Izmeri:

 OWOut DQ, 1, [$CC, $44]      ' Start merenja temperature
 Cekaj:    OWIn DQ, 4, [cr]     ' Provera da li jos traje
        If cr = 0 Then Cekaj
        
        OWOut DQ, 1, [$CC, $BE]      ' Procitaj izmerenu temperaturu
        OWIn DQ, 0, [tt.LOWBYTE, tt.HIGHBYTE]', Skip 4, cr, cpc]
        
        If tt.bit15=1 then
         znak4="-"
         tt = abs(tt)
        else
         znak4="+"
        endif
        tt=(tt>>1)*10+tt.0*5        
return

It's simple thermostat with hysteresis.
I tested it on easypic5 and PIC16F877, everything works great,but when I tried to compile for the PIC16F57, I got errors...
When I remove LCDOUT comands, then I get this:

Code:

Called Adresses must Reside in Lower Half of Page

I tried to reorganize the code, remove LCDOUT, but then i get an error when using I2C commands...

Code:

'@ DEVICE XT_OSC,WDT_OFF,PROTECT_ON
'DEFINE LCD_BITS 4
'DEFINE LCD_DREG PORTB
'DEFINE LCD_DBIT 0
'DEFINE LCD_RSREG PORTB
'DEFINE LCD_RSBIT 4
'DEFINE LCD_EREG PORTB
'DEFINE LCD_EBIT 5
'DEFINE LCD_LINES 2

DEFINE LCD_BITS 4
DEFINE LCD_DREG PORTB
DEFINE LCD_DBIT 0
DEFINE LCD_RSREG PORTA
DEFINE LCD_RSBIT 2
DEFINE LCD_EREG PORTA
DEFINE LCD_EBIT 3
DEFINE LCD_LINES 2    
    Tz var word
    Tt Var Word         
    Set var byte        
    Ton var byte
    Toff var byte
    Mode var byte
 
    CR Var Byte         
         
    
    Sn var byte
    Ss var byte
    
    Znak1 var byte
    Znak2 var byte
    Znak3 var byte
    Znak4 var byte

    I var byte
    
    symbol DQ = portb.4          
    symbol Tmode= portb.5
    symbol Tp=portb.6
    symbol Tm=portb.7
    symbol Rele=porta.1
    
    SYMBOL SCL = portc.4     
    SYMBOL SDA = portc.5
    
    input tmode
    input tp
    input tm
    output rele
    'adcon1=7
    clear
ss = tm         
rele=0
set=0
i=0
pause 100
'lcdout $fe,1, "....."
'Lcdout $fe, $C0," www....r"
pause 2000
'I2Cread SDA,SCL,$A0,0,[tz.lowbyte,tz.highbyte,toff,ton]
if tz>600 then tz=200
if toff=>100 then toff=5
if ton=>100 or ton=0 then ton=5

Pocetak:
sn = tmode
 if sn<ss then  set= set + 1
    
  if set>3 then 
   set = 0
  endif 
       
ss=sn
select case set
    CASE 0
     znak1=" "
     znak2=" "     
     znak3=" "
     'call izmeri
     OWOut DQ, 1, [$CC, $44]   ' Start merenja temperature
     OWOut DQ, 1, [$CC, $44]      ' Start merenja temperature
 Cekaj:    OWIn DQ, 4, [cr]     ' Provera da li jos traje
        If cr = 0 Then Cekaj
        
        OWOut DQ, 1, [$CC, $BE]      ' Procitaj izmerenu temperaturu
        OWIn DQ, 0, [tt.LOWBYTE, tt.HIGHBYTE]', Skip 4, cr, cpc]
        
        If tt.bit15=1 then
         znak4="-"
         tt = abs(tt)
        else
         znak4="+"
        endif
        tt=(tt>>1)*10+tt.0*5   
     i=0  
    
    CASE 1 
     znak1=">"
     znak2=" " 
     znak3=" "
     if tp=0 and tz<600 then 
      tz=tz+5
      i=0
     endif 
     if tm=0 and tz=>5 then 
      tz=tz-5 
      i=0  
     endif
      'I2CWrite SDA,SCL,$A0,0,[tz.lowbyte,tz.highbyte]
    
    CASE 2
     znak1=" "
     znak2=">"
     znak3=" "
     if tp=0 and ton<100 then 
      ton=ton+5
      i=0
     endif 
     if tm=0 and ton=>5 then 
      ton=ton-5
      if Ton=0 and toff=0 then ton=5
      i=0  
     endif
     'I2CWrite SDA,SCL,$A0,3,[ton]
     
    CASE 3 
     znak1=" "
     znak2=" " 
     znak3=">"
     if tp=0 and toff<100 then 
      toff=toff+5
      i=0
     endif 
     if tm=0 and toff=>5 then
      toff=toff-5 
      if Ton=0 and toff=0 then toff=5
      i=0  
     endif
     'I2CWrite SDA,SCL,$A0,2,[toff]
     
END SELECT 

 if tz+ton<=tt and set=0 and znak4="+" then 'ako je zadata temp manja od trenutne 
  rele=1                    'ukljuci rele
 endif                      
 if (tz=>toff and tz-toff=>tt and znak4="+") or (tz<toff and toff-tz<=tt and znak4="-" ) or set>0 then             'ako je zadata temperatura veca od trenutne ili si usao u meni
  rele=0
 endif
 
   
 i=i+1
 if i >100 then set = 4 'izadji iz menija

'call prikazi
       'Lcdout $fe,1,znak1,"+",DEC2 (tz / 10), ".",#(tz dig 0),223, "C"
       'if set=0 then lcdout $fe,$89,znak4,DEC2 (tt / 10), ".",#(tt dig 0) ,223, "C" '178
       'Lcdout $fe, $C0, znak2,"+",DEC2 (ton / 10), ".",#(ton dig 0),223, "C",znak3,"-",DEC2 (toff / 10), ".",#(toff dig 0),223, "C"        
    
pause 150
goto pocetak

If uncomment I2C or LCDOU, I get an error...
Sorry for bad English...

**Darrel Taylor** · - 7th October 2010, 01:48

The 16F57 is a 12-bit core, which only has 2 stack levels.
This puts restraints on what PBP can do.

Therefore you cannot use modifiers like DEC HEX STR etc. in your LCDOUT statements.
And I2C commands can only use fixed pins that are declared with DEFINE's.

DEFINE I2C_SCL PORTA,1
DEFINE I2C_SDA PORTA,0

You can do it by tomorrow ... maybe

**pedja089** · - 7th October 2010, 02:06

Thanks Darrel.
I read a datasheet, and again I have not paid attention to the MCU ...

I made a new PCB, the 16LF76, and works great ... now that I know what the problem is, I try to write a program that runs on 16F57. Now it should not be a problem.
Thanks again.

**mackrackit** · - 7th October 2010, 02:21

Maybe...
You can use SHIFTIN/OUT in place of I2C
http://www.picbasic.co.uk/forum/cont...-EEPROM-Part-1

**Darrel Taylor** · - 7th October 2010, 02:28

You can use the I2C statements with 12-bit cores.
You just need to DEFINE the SCL and SDA pins.

They still need to be specified in the I2C statements, but can't be changed at run-time.

**pedja089** · - 7th October 2010, 02:36

mackrackit,very nice explanation. I did not know exactly how I2C works, now I know.

It is easier to use and I2CREAD I2CWRITE, but this is also useful.

Thread: Pic16f57 + lcdout=error

Thread Tools

Search Thread

Display

Pic16f57 + lcdout=error

Members who have read this thread : 0

Bookmarks

Bookmarks

Posting Permissions