12f675_fuse_about_to_blow!

Quote:

---

Not a stupid question at all :)

---

Cheers mackrackit, I'm feeling better already I hope you are too!

So probably good practice to set VAR_IN_QUESTION = 0 just in case.

Hopefully I'll have moved the program on tomorrow, fingers x'd.

Right, time for me bed.

See you tomorrow.

Dave

Hint
COUNT is for pulses in a time period.

Maybe
if switch goes high
then
var = var + 1

Hi mackrackit,

Question: How long does it take LEDave to wire a push_button_switch to a PIC16F684?

Answer: About 48hrs:eek:

I think the program below should work ok:

Code:

---

Total var word
clear

MAIN:
if PORTA.5 = 0  then  count_up:
IF PORTA.5 = 1  THEN      MAIN:
   
Count_up:
let Total = Total + 1
pauseus 25 
LCDOUT $FE,1
LCDOUT $FE,$C0,DEC Total
PAUSE 500   
GOTO MAIN:

---

LEDave current status: Eyes going, mind boarderline!

Dvae

Quote:

---

Originally Posted by LEDave

I think the program below should work ok:

Code:

---

Total var word
clear

MAIN:
if PORTA.5 = 0  then  count_up:
IF PORTA.5 = 1  THEN      MAIN:
   
Count_up:
let Total = Total + 1
pauseus 25 
LCDOUT $FE,1
LCDOUT $FE,$C0,DEC Total
PAUSE 500   
GOTO MAIN:

---

---

It looks good.

Quote:

---

LEDave current status: Eyes going, mind boarderline!

Dvae

---

Hey, that means you have passed the initiation and are a full codder now. :p

So the next thing it to WRITE 'Total' to EEPROM address, then READ that value and put it back into 'Total'.

The theory is that when the PIC power supply is turned off then restarted last 'Total' reappears on the LCD.

Dave

Yup, that is the mission :)

From the manual:

Code:

---

WRITE Address,Value

---

So looking at the 16F684.PDF it says:

Quote:

---

The PIC16F684 has 256 bytes of data EEPROM
with an address range from 0h to FFh.

---

So would:

Code:

---

WRITE 0h,Total

---

work? Not quite as simple as that he says! For one thing these are EEPROM BYTES and 'Total' is a WORD two BYTES for a starter.

Dvae

You do not need to use HEX numbers for the address, PBP takes care of that.

http://www.melabs.com/resources/samples.htm
Might find the above .... interesting

Mmm. Well I kind of think I know what I have to do, it's break the VAR WORD Total up into two BYTES, allocate them each a memory space B1 & B1+1 (from the prog below) WRITE the BYTES to the memory locations then READ them back.

Code:

---

        INCLUDE "modedefs.bas"          ' Include serial modes

SO      VAR                PORTC.6                                        ' Define serial output pin

B1      VAR    BYTE                                        ' Address variable
W2      VAR    WORD                                        ' Data variable


mainloop: 

                For B1 = 0 To 12 step 2                        ' Step 2 because each word requires 2 bytes of memory
                W2 = B1 + 1000                  ' Add 1000 to address
                Write B1, W2.HIGHBYTE                ' Write high byte of word
                Write B1+1, W2.LOWBYTE                ' Write low byte of word to next address
                Next B1

                For B1 = 0 To 12 step 2                        ' Step 2 to get word size data
                Read B1, W2.HIGHBYTE                ' Read high byte
                Read B1+1, W2.LOWBYTE                ' Read low byte
                SerOut SO,T2400,[#W2," ",10,13]        ' Display the word data
                Next B1
               
        SerOut SO,T2400,[10,13,10,13]        ' Skip 2 Lines

        GoTo mainloop                      ' Forever

---

My reading of the program above is that B1 = 's ( 0,2,4,6,8,10,12) + 1000 this is then written and read from memory location B1 & B1+1 into WORD W2 am I close?

Dave

Quote:

---

Originally Posted by LEDave

My reading of the program above is that B1 = 's ( 0,2,4,6,8,10,12) + 1000 this is then written and read from memory location B1 & B1+1 into WORD W2 am I close?

---

Sounds like you understand it. Have you tried it yet?

Quote:

---

Sounds like you understand it. Have you tried it yet?

---

I'm on it.......

I modified it to run on my LCD and it counts from 1000 to 1012 by adding two, then does it all over again.

So the first loop is WRITING the count to memory and the second is READING and displaying from memory to the LCD. B1 being the high BITS of the BYTE that make up W2 and B1+1 the low bits of W2, is that right?

So to complete our 'mission' should I try and do the same and use a loop or assign BYTES to a WORD (if that makes sense).

Dave

Quote:

---

Originally Posted by LEDave

I modified it to run on my LCD and it counts from 1000 to 1012 by adding two, then does it all over again.

So the first loop is WRITING the count to memory and the second is READING and displaying from memory to the LCD. B1 being the high BITS of the BYTE that make up W2 and B1+1 the low bits of W2, is that right?

---

Yup!

Quote:

---

So to complete our 'mission' should I try and do the same and use a loop or assign BYTES to a WORD (if that makes sense).

Dave

---

????

You have the WORD size var holding the value of how many times the switch was pressed. Use the high byte low byte thing from above for writing every time the switch is pressed. Only need to read the EEPROM when the chip starts.

Something like that:)

Quote:

---

Something like that:)

---

I'll give it a go, not a 100% sure on this one but I'll give it go.

This is brilliant stuff though, cheers mackrackit.

Dave

Mission clarification

Power UP
Read EEPROM
Transfer value from EPROM to VAR

Press Button
VAR adds one to it's self
Display VAR on LCD
Write VAR to EEPROM
Wait for another Button press

This message will self destruct in.....

:):):)

I'm on it boss 'NCIS'.....!

Dave

Hi mackrackit,

I've not been able able to look at the project this weekend due to a family issue.

Will be back 'on mission' tomorrow all being well.

Dave

Yup, family comes first. In the end that is all we got.

Hope things turn out well.

Quote:

---

Yup, family comes first. In the end that is all we got.

---

Never a truer word....

Quote:

---

Hope things turn out well.

---

Thank you and they have I'm very relieved to say.

Back on the case tomorrow after a good nights sleep.

Dave

Hi mackrackit,

Things pretty much back to normal here (panic over):)

So here's the first part of the brief, I think it covers these components:

Quote:

---

Power UP: Read EEPROM: Transfer value from EPROM to VAR: Press Button:
VAR adds one to it's self: Display VAR on LCD

---

I didn't want to try and do any more just in case I'm wildly off track on this, what do you think? I've left out all the DEFINES for clarity.

Code:

---

Total var word        ' Data variable
B1      VAR    BYTE  'Stored DATA address
clear                'Re_set volatile memory to zero (Not EEPROM?)

MAIN:
gosub Power_up        'On Power_up GOTO READ EEPROM subroutine
Start:
if PORTA.5 = 0  then  count_up: 'If button pressed start counting
IF PORTA.5 = 1  THEN    Start: 'If button not pressed loop until it is
   
Count_up:                'Button has been pressed
let Total = Total + 1    'Add one to value of Total taken from EEPROM 
LCDOUT $FE,1              'Clear LCD
LCDOUT $FE,$C0,DEC Total  'Display Total on LCD
PAUSE 500
GOTO Start:

Power_up:                'Power_up subroutine
Read B1, Total.HIGHBYTE          ' Read high byte
Read B1+1, Total.LOWBYTe  ' Read low byte 
LET Total = Total        'Set Total to value set in EEPROM Memory
return

---

Dave

Glad to hear things are back to normal.

A quick look and it looks OK, might want to add a WRITE to EEPROM routine though...

Quote:

---

Glad to hear things are back to normal.

---

Cheers mackrackit, it was a real worry there for a while.....

Quote:

---

might want to add a WRITE to EEPROM routine though...

---

I'm be on it tonight.

Dave

Hi mackrackit,

I've added the WRITE to EEPROM routine. Also @power_up the LCD was blank, so I
added an LCDOUT statement to the Power_up Subroutine which now displays the last stored
EEPROM value.

The whole thing works a treat:):) I can see the merits of being able to write data to a non volatile memory, really,really useful. Thanks for stearing me through this one (as ever) very clever.

Code:

---

Total var word        ' Data variable
B1      VAR    BYTE  'Stored DATA address
clear                'Re_set volatile memory to zero (Not EEPROM?)

MAIN:
gosub Power_up        'On Power_up GOTO READ EEPROM subroutine

Start:
if PORTA.5 = 0  then  count_up: 'If button pressed start counting
IF PORTA.5 = 1  THEN    Start: 'If button not pressed loop until it is
   
Count_up:                'Button has been pressed
let Total = Total + 1    'Add one to value of Total taken from EEPROM
 
LCDOUT $FE,1              'Clear LCD
pause 150
LCDOUT $FE,$C0,DEC Total  'Display Total on LCD
Write B1, Total.HIGHBYTE  ' Write high byte of Total word to EEPROM
Write B1+1, Total.LOWBYTE ' Write low byte of Total word to next address
goto start:
 
Power_up:                'Power_up subroutine
Read B1, Total.HIGHBYTE          ' Read high byte
Read B1+1, Total.LOWBYTe  ' Read low byte 
LET Total = Total        'Set Total to value set in EEPROM Memory
LCDOUT $FE,1              'Clear LCD
pause 150                'Give LCD a chance to Power_up
LCDOUT $FE,$C0,DEC Total  'At Power_up display Total on LCD from EEPROM
                          'Memory which has been stored since Power_down
return

---

Just going to pop around my bench to turn the power back on........Yep still working :)

Dave

COOL!!!!:D

Do you want another mission? :p

Quote:

---

Do you want another mission?

---

You bet, I wanted you to sign me off on the last Mission first though:D

It's one thing me thinking I've done something right, it's another being told I have.

Dave

So far you have been letting PBP take care of the EEPROM address "B1".
Now we want to control where in the EEPROM data is written to as we will be storing and retrieving multiple pieces of data.

Using the same basic scenario as before, part counting on a conveyor.
This time the machine and personnel have been upgraded to run 24/7. The only time the machine will be shut down is for maintenance, scheduled or un-scheduled.

Management still wants to know the total parts ran, and the maintenance department wants to know how many parts are being ran between shut downs, how many shut downs there were and because they are lazy they also want the machine to average the amount of parts ran between each down.

Who says computers and automation cuts jobs? We went from running one shift to three and added coder to the mix along with all of the supply/demand personnel to handle the increased production.

Ok.....Mmm...,

Quote:

---

Now we want to control where in the EEPROM data is written to as we will be storing and retrieving multiple pieces of data.

---

Well for this I'm thinking (although I could be wrong here):

Code:

---

WRITE 5,B0 ' Send value in B0 to EEPROM location 5

---

So we need:

1/ Total parts run

2/ Total parts run before M/C stops for maintenance

3/ How many times M/C shuts down (scheduled + un_scheduled)

4/ The average amount of parts run between each shut down (scheduled + un_scheduled)

I think I've read that right?

Dave

Quote:

---

Originally Posted by LEDave

Code:

---

WRITE 5,B0 ' Send value in B0 to EEPROM location 5

---

---

Yup

Quote:

---

1/ Total parts run

2/ Total parts run before M/C stops for maintenance For each run, need multiple address here too.

3/ How many times M/C shuts down (scheduled + un_scheduled)

4/ The average amount of parts run between each shut down (scheduled + un_scheduled)

---

Remember two address locations for WORD size variables.
Hopefully the machine will run long enough to need a WORD VARs for parts run between shut downs, and if all goes well the machine will not shut down often so a BYTE size VAR should work for "times shut down".

I'm on it, tricky in parts but I'm on it:)

How many EEPROM locations are there on a PIC16F684?

As in:

Code:

---

EEPROM location 5

---

Dave

I think the 684 only has 256, if I remember correctly.

Is that sequential 0-255?

Srub that, it's got to be I'm thinking.

See you tomorrow.

Dave

Hi mackrackit,

I'm busy working on the latest 'mission'. I'll stick at it and only ask a question when I'm stuck and have given it a good go to figure it out myself.

I do have one quick question though:

Can you add or subtract EEPROM memory location values (numbers written to an EEPROM address)? Or do you just give the stored WORD's a name and then subtract the two, something like: Parts_Run = Total - First_Parts_run (if this make sense).

Dave

While the value is in the EEPROM you can not go anything with it. You have to read the value into a variable, do something with it and write it back into the EEPROM.

I think that is what you are asking...

Quote:

---

I think that is what you are asking...

---

Spot on.

Dave

I can almost hear mackrackit tapping his fingers on the table............!;)

Working really hard on this, I know what I want to do, I just need a breakthrough. At the moment I'm going around in circles.

I'll see what I can come up with tonight.


Tap, tap, tap...Stop it mackrackit...lol.

Going around in circles?
You mean stuck in a loop :D

tap tap tap
that is funny :)

Quote:

---

You mean stuck in a loop

---

:)

Yep,exactly that:eek:

If I can't crack it by tomorrow night I'm going to have to ask for a pointer. I was going to ask for one tonight but I think I'm in the right ball park for a small break through (he typed deludedly but hopefully).

Dave

Mmmm,

Quote:

---

You mean stuck in a loop

---

Cryptic I know but are you 'hinting' that the way to do part two of the mission, namely:

Quote:

---

Total parts run before M/C stops for maintenance For each run

---

Is to have the Total count (part one of mission) actually run inside a WORD size loop and Total parts run is actually the loop count itself? So that whenever the loop stops (ie, MC stops) that value is then written to EEPROM as Total parts run?

The thinking would then be that Total count just carries on and parts run ie the loop count resets to zero and then starts again on power up.

Dave

Quote:

---

The thinking would then be that Total count just carries on and parts run ie the loop count resets to zero and then starts again on power up.

---

And writes to a different EEPROM location each time. So if you have five start ups you will have five EEPROM locations (10 actually, 2 per WORD), plus the pair of locations for the TOTAL.

Quote:

---

And writes to a different EEPROM location each time.

---

More to think about there then.All part of the learning process.

Learning how to program these PIC's is like learning a foreign language, doing a crossword puzzle and a Rubick's cube (all at the same time)...:eek:

It'll come with time and practice though (I hope...!)

Dave