Bootloader

Can someone please help me i am trying to get a boot loader working(first timer) i use the microchip loader for the 18F4550 over USB

The problem is that everything works the first time but when i open my hex file the loader comes up with a message that the config differs from the board, if i choose to use the board everything keeps on working but when i use the config from the hx file it seems to overite something in the bootloader code. after the chip resets the program works but i can't go back into bootloader mode. here is my code anyone got any ideas?

Code:

---

INCLUDE "MODEDEFS.BAS"

DEFINE LOADER_USED 1
DEFINE RESET_ORG 1000h ' For Microchip USB Bootloader

DEFINE OSC 20                                ' Define crystal as 20Mhz

'Define ACDIN parameters
Define ADC_BITS 10                        ' Set number of bits in result
DEFINE ADC_CLOCK 3                        ' Set clock source ( 3 = RC )
DEFINE ADC_SAMPLEUS 50                ' Set sampling time to micro-seconds

'This Part set PORTA 0-3 an analog inputs,4 as digital
TRISA = %00011111                        'set PORTA 0-5 as inputs
ADCON1 = %00001010                        'ADC use vss and vdd as ref.
ADCON2 = %10000111                        'FRC (clock derived from A/D RC oscillator),Right justify output

TRISC = %10000000
TRISD = %00001111                        'Set port d 0-3 as inputs and 4-7 as outputs
TRISB = %10011000

'**************************************Serial port setup*************************************
'*Serial port Setup 9600 8N1*
DEFINE HSER_BAUD 9600                ; 9600 Baud
DEFINE HSER_RCSTA 90h                ' Enable serial port & continuous receive
DEFINE HSER_TXSTA 24h                ' Enable transmit, BRGH = 1
DEFINE HSER_CLROERR 1                ; Clear overflow automatically
DEFINE HSER_SPBRG 129

'**************************************Variables*********************************************
buffer        Var        Byte[16]
cnt        Var        Byte
LED        Var        PORTD.4


USBInit
Low LED                ' LED off

'**************************************Main Program******************************************

idleloop:
        PORTD.7 = 1
        PAUSE 1000
        PORTD.7 = 0
        PAUSE 1000


        Goto idleloop        ' Wait for next buffer


END

---

The Microchip USB loader expects the CPU core to be running at 48MHz. Just change your
DEFINE OSC to 48, and accept the default config settings - unless you know enough to
modify the USB C loader firmware to operate at a different oscillator speed.

Hi there i have changed my cristal to a 48M but now my bootloader does not work, after mor reading on this forum i came to another link saying the bootloader works on 20M
http://www.picbasic.co.uk/forum/showthread.php?t=5590
if i go back to a 20M everything seems to work the problem seemed to be that the config in the include file (18f4550.inc) and in the microchip main.c needs to be the same.

Now i have another question since i have 48M cristals how do you convert the bootloader to work on 48M??:cool:

I know this is not the c forum but mabe someone can help this is the config i have in the main.c file of the bootloader is this correct and is there other places i have to edit to get it working my PC keeps on poping up with unregognised device

Code:

---

#if defined(PIC18F4550_PICDEM_FS_USB)                // Configuration bits for PICDEM FS USB Demo Board
        #pragma config PLLDIV  = 12        // (48 MHz crystal on PICDEM FS USB board)
        #pragma config CPUDIV  = OSC1_PLL2       
        #pragma config USBDIV  = 2        // Clock source from 96MHz PLL/1
        #pragma config FOSC    = HSPLL_HS
        #pragma config FCMEN    = OFF
        #pragma config IESO    = OFF
        #pragma config PWRT    = OFF
        #pragma config BOR      = ON
        #pragma config BORV    = 3
        #pragma config VREGEN  = ON                //USB Voltage Regulator
        #pragma config WDT      = OFF
        #pragma config WDTPS    = 32768
        #pragma config MCLRE    = ON
        #pragma config LPT1OSC  = OFF
        #pragma config PBADEN  = OFF

---