Wireless modules FCC approved

[Michael]

Also -- If you had a choice, everything else being equal....

In a typical modern office building with a lot of steel construction etc would you...

2.4ghz at 50mw

or

900mhz at 100mw

?

What's the general consensus on that?

A real difference or 6 to 1?

[dhouston]

AFAIK, anything sold assembled and ready to use requires FCC testing. The testing is expensive which (in part) explains the high cost of pre-approved modules. Even receivers require testing - it's not only transmitters. You really need to read the Part 15 documentation.

• http://www.fcc.gov/oet/info/rules/

Her's a link with some data on indoor propagation.

• http://sss-mag.com/indoor.html

[Archangel]

Higher the Frequency, the more line of sight the signal becomes, lower the power the shorter the range, that said the higher Frequency units might be a little less affected by noise.

[Bruce]

Even if you toss a pre-certified module into your product, it will most likely still need FCC
cert before you can sell it. Contact one of the certified test labs if you aren't 100% sure.

These guys are one of the best http://www.celectronics.com/

The finished product (even if it uses a pre-certified module), may still need final certification
of the finished product before you can legally sell it.

An FCC certified test facility will tell you straight-up if your product needs further FCC cert.

They will tell you without charging you for the info, and it's worth the effort.

[earltyso]

I have looked into FCC testing myself, only 3-5k if you've got spare change.
Linx Technologies has got some great material on the subject.

After looking through LINX technologies website and making my list of (should have learned this in college EE Communications) questions I called LINX to ask the same kinds of questions you have been asking. Everything posted so far sounds in line with what I was told my the antenna factory/ linx rf modules guys.

One thing to consider is what kind of data are you sending?

Continuous? Intermittent?

900Mhz alows for continuous data but 433-434 Mhz does not. If you are just using rf modules for hobby work or you don't care about FCC rules (you obviously do) you can just send continuous data in a loop at lower freq with lower cost modules from Linx.

Also most of the rf modules require line of sight applications to get the full range advertised by the companies making them.

I admit that I have limited knowledge as I have only been designing with rf for a few years now. So far I have used the LINX KH2-xxx-xx & LR-xxx-xx modules both at 433Mhz. I was cheap and did not buy the prebuilt development boards. So to save my time/money/heartache from a wasted prototype.... I called LINX with LOTS of questions about laying out my ground planes, rp coax connections, etc before having my PCB's made. Taking my time and calling their tech support was worth it. I

totally recommend reading all you can from their FCC dowloads, rf for tech challenged, antenna theory manuals and give em a call. The last guy I spoke with (at linx) was an rf communications vet of 25 years in IRAN, IRAQ, CANADA with military and non military rf design experience. They know their stuff! Hope this helps!

[earltyso]

Just thought I would throw in a plug for Bruce @ Rentron,
I bought my first RF modules in college (4 years ago) from their website and I was very impressed with the service I recieved and variety of low cost rf parts/ examples they offered.
Great job guys!

[greensasquatch]

I know most people are biased against products made in China but I've been using some from an ebay seller http://stores.ebay.com/e-MadeinCHN for a while now, they work great (haven't tried serial yet, just controls).
They have great customer service and I'm pretty sure they are FCC approved. They have a website at http://www.e-madeinchn.com/

Much cheaper than most wireless modules I've found.

hope this helps

[Archangel]

I know most people are biased against products made in China but I've been using some from an ebay seller http://stores.ebay.com/e-MadeinCHN for a while now, they work great (haven't tried serial yet, just controls).
They have great customer service and I'm pretty sure they are FCC approved. They have a website at http://www.e-madeinchn.com/

Much cheaper than most wireless modules I've found.

hope this helps

99% of everything is made in China! Here is what ticks me off . . . you buy Chinese cheapie, it's made in China, You buy a name brand, likely it's made in China, especially true when buying for the machine shop, now the Chinese know their electronics, but their non electronic items are all over the place, from trash to treasure. Buying from China on eBay just cuts out the (Your Country's Name Here) dealers and sales taxes. So if you buy there be sure the price is much, much lower, < wholesale, otherwise in the long run, you are losing, 'cause when your local dealers go away, the Chinese prices will go up, up, up. The eBay sellers will negotiate their prices, believe me.
JS