Circuitry design


Closed Thread
Results 1 to 10 of 10
  1. #1
    Join Date
    Sep 2008
    Posts
    19

    Default Circuitry design

    I have a circuitry with 3 servo motors + pic.

    I am using two parallel 7805 for the motors and one only for the pic.

    Unfortunately I found that a choppy servo motor behaviour is due to not enough current being delivered - ie I am working with interrupts so two servos need current at the same time.

    I found that one (of the parallel) 7805 remains cold while the other one is becoming very hot.

    Should there be one 7805 for each motor + one for the pic, ie 4x7805 or should my current configuration be sufficient but one 7805 is faulty or some other solution?

    Maximum current per 7805 is 1A accord. to the data sheet.

  2. #2
    Join Date
    Nov 2003
    Location
    Wellton, U.S.A.
    Posts
    5,924


    Did you find this post helpful? Yes | No

    Default

    This is easier than getting the load balanced between multiple 7805 regulators.
    http://www.national.com/mpf/LM/LM350.html
    3 amps with heat sink.
    Use the LM350 for the motors and a 7805 for the PIC.

    If you still want to parallel the 7805s, bend the legs so one heat sink can be attached to all of them at the same time (chips side by side) . The legs should be bent enough to allow at least 0.20 inch traces on all legs. Do not use a set of capacitors for each regulator. Put together as stated and you have one big regulator.

    Or you have a bad 7805.
    Dave
    Always wear safety glasses while programming.

  3. #3
    Join Date
    May 2004
    Location
    NW France
    Posts
    3,651


    Did you find this post helpful? Yes | No

    Wink

    Hi Security,

    You also can use a PNP Ballast to boost the 7805 regulator output ...

    See National Datasheets ( Lm 317,350,338 ) AND MC78xx Datasheets for such info.

    Do not forget to use a Large value Low ESR capacitor to allow current "surges" ...

    Alain
    ************************************************** ***********************
    Why insist on using 32 Bits when you're not even able to deal with the first 8 ones ??? ehhhhhh ...
    ************************************************** ***********************
    IF there is the word "Problem" in your question ...
    certainly the answer is " RTFM " or " RTFDataSheet " !!!
    *****************************************

  4. #4
    Join Date
    Sep 2008
    Posts
    19


    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by mackrackit View Post
    This is easier than getting the load balanced between multiple 7805 regulators.
    http://www.national.com/mpf/LM/LM350.html
    3 amps with heat sink.
    As both 7805 are parallel does that mean I can just replace one of them with a LM350 and remove the other one?

  5. #5
    Join Date
    Nov 2003
    Location
    Wellton, U.S.A.
    Posts
    5,924


    Did you find this post helpful? Yes | No

    Default

    Yes, one 350 will take the load of two 7805s. The pin out is different and you need external resistors to set the voltage of the 350 because it is adjustable, so it is not a direct replacement on a PCB.
    Dave
    Always wear safety glasses while programming.

  6. #6
    Join Date
    Sep 2008
    Posts
    19


    Did you find this post helpful? Yes | No

    Default

    I prefer to not redesign my current circuitry. What about other components doing the trick fitting in the position of my 7805?

    PS: If I actually had to redesign my circuitry I would use http://www.elecfree.com/electronic/5...ly-by-tip2955/.

  7. #7
    Join Date
    Nov 2003
    Location
    Wellton, U.S.A.
    Posts
    5,924


    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Security View Post
    PS: If I actually had to redesign my circuitry I would use http://www.elecfree.com/electronic/5...ly-by-tip2955/.
    Yep, that would work to. Just like Alan suggested.
    Dave
    Always wear safety glasses while programming.

  8. #8
    Join Date
    Jul 2003
    Posts
    2,358


    Did you find this post helpful? Yes | No

    Default

    A 78S05 is a 2A version of the 7805.

  9. #9
    Join Date
    May 2004
    Location
    NW France
    Posts
    3,651


    Did you find this post helpful? Yes | No

    Talking Ahhhh, ... inflation ...

    Hi,

    And a 78T05 CT ( Motorola ) is the 3Amps TO 220 model ...

    also the LT 1085 CT 5 ...

    in TO3 case, you have the LM 323 K

    But do not forget the convenient heatsink !!! - what about your transformer and rectifiers ???

    Alain
    Last edited by Acetronics2; - 6th September 2008 at 10:13.
    ************************************************** ***********************
    Why insist on using 32 Bits when you're not even able to deal with the first 8 ones ??? ehhhhhh ...
    ************************************************** ***********************
    IF there is the word "Problem" in your question ...
    certainly the answer is " RTFM " or " RTFDataSheet " !!!
    *****************************************

  10. #10
    Join Date
    Sep 2008
    Posts
    19


    Did you find this post helpful? Yes | No

    Wink Solved

    Good idea Acetronics, that is exactly what I want.

    Problem solved.

    Thread can be closed.

Similar Threads

  1. Propeller Clock Advanced Design
    By Balachandar in forum mel PIC BASIC Pro
    Replies: 6
    Last Post: - 21st June 2022, 20:38
  2. how large and complex firmware you design using pbp?
    By chrdcv in forum mel PIC BASIC Pro
    Replies: 17
    Last Post: - 22nd December 2008, 00:30
  3. PIC16F88 senior design
    By AlaskanEE in forum Serial
    Replies: 71
    Last Post: - 2nd May 2007, 14:06
  4. need advice on selling my design
    By nimonia in forum Off Topic
    Replies: 13
    Last Post: - 2nd March 2007, 23:27
  5. PCB Design Partnership Enquiry;
    By arbel in forum Adverts
    Replies: 0
    Last Post: - 15th February 2007, 08:07

Members who have read this thread : 0

You do not have permission to view the list of names.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts