Well I was able to write a test code for the clock function if anyone is intrested. Works very good!
|
Well I was able to write a test code for the clock function if anyone is intrested. Works very good!
Last edited by Original; - 14th November 2003 at 06:17.
|
Re: Hdsp 21xx display
Hi friends,
I know that this is a really old topic, but, last week I got 3 of this display for free from a friend.
They are nice, bright, and has a good "retro" looking.
I did many many tests and I was unable to get a stable result from the display. They are brand new, never used.
I test the Rentron´s Hello moving message an the clock published here.
Both, I get ramndom characters and a strange behavior.
I´m using a 16F877 @ 10 Mhz (I did tests @ 20 Mhz also)
I´m using the wiring suggested by rentron :
'* // Display connections * //'
' PortB Display | PortA Display | PortC Display
' B0 #19 | A0 #3 | C0 #13
' B1 #20 | A1 #4 | C1 #6
' B2 #23 | A2 #5 | C2 #1
' B3 #24
' B4 #25
' B5 #26
' B6 #27
' * // Display GND, VCC and N.C. [no connection] * //'
' GND 15,16,17,28
' VCC 2,7,8,9,10,11,14,18
' N.C. 12
and the source code :
Code:DEFINE OSC 10 ' 4MHz oscillator @ ERRORLEVEL -306 ; Retira o erro de crossing page boundary ;@ __CONFIG _CP_OFF & _DEBUG_OFF & _CP_OFF & _CPD_OFF & _LVP_OFF & _BODEN_OFF & _PWRTE_ON & _WDT_OFF & _HS_OSC @ __CONFIG _HS_OSC & _CP_OFF & _DEBUG_OFF & _CPD_OFF & _LVP_OFF & _PWRTE_ON & _WDT_OFF TRISA = 0 ' Setup PortA = output for Address Bus TRISB = 0 ' Setup PortB = output for Data Bus TRISC = 0 ' RC.7 = input, rest outputs [used for loader] ADCON1 = 7 ' A/D OFF A_Bus VAR PORTA D_Bus VAR PORTB ' PortB = Data Bus W_Pin VAR PortC.0 ' HDSP-2112 write strobe pin #13 A3 VAR PortC.1 ' HDSP-2112 mode select pin #6 FL VAR PortC.4 'Flash mode select RST VAR PortC.2 ' HDSP-2112 reset pin #1 Digit VAR BYTE[8] ' 8-byte digit array DigPat VAR BYTE ' Digit pattern from lookup table LP_Cnt VAR BYTE ' Loop counter LowDig VAR BYTE ' Holds "low" digit # to lookup LowDig = 0 ' 1st digit = 0 HiDig VAR BYTE ' Holds "high" digit # to lookup HiDig = 7 ' Last digit = 7 J VAR BYTE ' Array index pointer J = 0 ' 1st byte in array S_Speed VAR WORD ' Holds display scroll speed S_Speed = 200 ' Set display scroll speed here Low D_Bus.7 ' Set display for normal operation EOM CON "~" ' Character used as "End of Message" marker hour VAR BYTE ' Define hour variable dhour VAR word ' Define display hour variable minute VAR BYTE ' Define minute variable second VAR BYTE ' Define second variable ticks VAR BYTE ' Define pieces of seconds variable update VAR BYTE ' Define variable to indicate update of LCD second10 var byte min10 VAR BYTE hour10 VAR BYTE i var word ADCON1 = 7 second10 = 0 hour = 0 ' Set initial time to 01:00:00 hour10 = 6 minute = 0 min10 = 0 second = 0 ticks = $00 update = 0 OPTION_REG = $55 ' Set TMR0 configuration and enable PORTB pullups INTCON = $a0 ' Enable TMR0 interrupts On Interrupt GoTo tickint ' '* // Initialize display - then set brightness * //' Init_Display: ' * // Initialize Display Here * //' High W_Pin : Low RST : Pause 20 : High RST : High FL : Pause 20 ' * // Set Display Brightness Here * //' ' To change display brightness ' D_Bus = | 0 | 1 | 2 | 3 | 4 | 5 | 6 | ' Bright =| 100% | 80% | 53% | 40% | 27% | 20% | 13% | ' ' Set 27% | mode.bit | strobe settings into display | D_Bus = %0001100 : Low A3 : Low W_Pin : High W_Pin High A3 ':HIGH FL' A3 used only for setting display brightness '* // Get 8 digits into "Digit Array" for display * //' GetDig: For LP_Cnt = LowDig TO HiDig LookUp LP_Cnt,[" : : "],DigPat Digit[J] = DigPat ' Load all 8 digits into array J = J + 1 ' Increment array index pointer Next ' Loop until we have all 8 digits loaded J=0 ' Re-set array index pointer LowDig = LowDig ' Increment to next "low" digit HiDig = HiDig ' Increment to next "high" digit '* // Display 8 digits on display then return for more // *' DisplayDigit: For LP_Cnt = LowDig TO HiDig ' Scroll right-to-left A_Bus = LP_Cnt ' Place digit address on address bus D_Bus = Digit[J] ' Place digit data on data bus Low W_Pin : High W_Pin' Strobe data into display J = J + 1 ' Increment array pointer to next digit DigPat = DigPat Next J = 0 chkup: 'While hour = 1 and hour10 = 3 ' hour = 0 ' hour10 = 1 ' wend A_Bus = 7 D_Bus = 48 + second10 Low W_Pin : High W_Pin Pause 10 A_Bus = 6 D_Bus = 48 + second Low W_Pin : High W_Pin Pause 10 A_Bus = 4 D_Bus = 48 + min10 Low W_Pin : High W_Pin Pause 10 A_Bus = 3 D_Bus = 48 + minute Low W_Pin : High W_Pin Pause 10 A_Bus = 1 D_Bus = 48 + hour10 Low W_Pin : High W_Pin Pause 10 A_Bus = 0 D_Bus = 48 + hour Low W_Pin : High W_Pin Pause 10 IF update = 1 Then update = 0 endif Goto chkup Disable tickint: ticks = ticks + 1 ' Count pieces of seconds IF ticks < 165 Then tiexit ' One second elasped - update time ticks = 0 second10 = second10 + 1 IF second10 >= 10 Then second10 = 0 second = second + 1 IF second >= 6 Then second = 0 min10 = min10 +1 IF min10 > 9 THEN min10 = 0 minute = minute + 1 IF minute >= 6 Then minute = 0 hour10 = hour10 + 1 IF hour10 > 9 THEN hour10 = 0 hour = hour + 1 IF hour > 2 Then hour = 0 ENDIF ENDIF EndIF EndIF EndIF ENDIF update = 1 ' Set to update LCD tiexit: INTCON.2 = 0 ' Reset timer interrupt flag Resume End
Have someone here ever used this kind of display ?
thanks !
Sérgio
|
Re: Hdsp 21xx display
Hi friends !
I did find my problem.
I was using a really noisy power supply.
Afeter changing it to another one, everything is working fine !
Thank you !
Members who have read this thread : 0You do not have permission to view the list of names.
Posting Permissions
Bookmarks