RF12 module need to convert some C to Basic

[davewanna]

This is mostly just an excercise for a project of mine. The way the module is toted, is that it can output a clock signal for the pic, so only the crystal on the module is needed, and not 2 seperate oscillators. The examples I have seen of this module being used in the real world have had the osc out line connected to the pic. I have now got this part working though, and it is not a problem.

Cheers

[dhouston]

Do you have to reset the registers each time the RF12 starts or are they non-volatile so that the clock frequency will always be 10MHz (or whatever) once set? In my experience, registers like these are usually non-volatile.

[Bruce]

uchar RGIT=0; unsigned char RGIT = 0
uint temp=0xB800; unsigned int temp = B800 hex
temp|=DATA; temp = temp ORed with the value in DATA

[davewanna]

dhouston,

So far the registeres are reset when the power is removed. i.e. everytime I restart the module, the OSC is back to 1MHz.

I did read in one of the datasheets, but I can't find it now, something along the lines of that you have to reset the module after changing settings for them to be stored. Not 100% sure of this right now. But I haven't had any luck attempting it so far.


Bruce,

What do you mean ORed?

I'm struggling to get the over-all picture of what it sends here.

From my understanding.. to actually send data.. I must use the "WriteCMD loop from earlier, to send first $b8, and then another 8bits of data.

Which I have done by...

WriteFSKbyte:
...
temp = $b8
SCK = 0
SDI = 1
nSEL = 1
dout.highbyte = temp
dout.lowbyte = dat
gosub writecmd

Now currently there is what I presume is a preamble..

  dout = $8228            'open PA
  gosub writecmd
  pauseus 4
  dout = $8238            'something to do with transmit register
  gosub writecmd
  pauseus 2
  dat = $AA
  gosub writefskbyte    'send $B8AA
  gosub writefskbyte    'send $B8AA
  dat = $2D
  gosub writefskbyte    'send $B82D
  dat = $D4
  gosub writefskbyte    'send $B8D4

That should actually transmit.... "$AAAA, $2DD4 " ????????

Suffering from severe lack of experience in RF and/or serial transmission, when should I send the pre-amble? Before every transmission?

i.e.
Preamble,
Transmit data, - Several 16bit segments...
Pause
do whatever else..
Preamble
Transmit data
etc??

[skimask]

I did read in one of the datasheets, but I can't find it now, something along the lines of that you have to reset the module after changing settings for them to be stored. Not 100% sure of this right now. But I haven't had any luck attempting it so far.

Don't see anything about that.

What do you mean ORed?

Logical OR'ing. It's in the manual, or look it up on Wiki under Boolean logic.

I must use the "WriteCMD loop from earlier, to send first $b8, and then another 8bits of data.

ShiftIn/ShiftOut will work just fine with this chip, no need to reinvent the wheel as you have been doing.

[davewanna]

I knew I was in above my head, and would do something stupid like try to re-invent the wheel. Oh well, at least I'm learning..

To counter that last statement though, would you believe I took "ORed" as "O-Red" and thought it was some C statement I didn't know about.. Really quite obvious now... stupid me.

I think I will just keep re-inventing the wheel until it's almost as good as the one we got now, then chuck it out and go with the tried and tested. At least by then I might know more about the module, and might have more luck trying the shiftout commands...

[Wirecut]

Hi davewanna

at the end; what about your project.

Are you satisfied about the RFM12.

I have just ordered some of that modules to make some RF trial; as I'm a novice in RF and SPI interfacing.

I have in plan to use this module with a 16F877 just to make experience before use it on a real project.

After reading the full tread, I have now a gray view of the problem that I will encounter to make the RF connection working. From your experience and your point of view, do you have any helpfull suggestions about PBP and the RFM12 module interfacing?

Ciao

Leo

[Archangel]

I think I will just keep re-inventing the wheel until it's almost as good as the one we got now, then chuck it out and go with the tried and tested. At least by then I might know more about the . . .

My God, Dave, that's brilliant ! That exactly describes the HUMAN LEARNING PROCESS ! I have never seen it put just that way. I really mean it, Good Job.