PIC16F690 - 24LC08B: they won't talk...

[sayzer]

First things at first look.

1. You set your OSC at 8Mhz. This is for your PIC. You must DEFINE OSC speed to the compiler also. Have DEFINE OSC 8.

2. For PIC16F690, SDA should be RB4 and SCL should be RB6.

[xnihilo]

First things at first look.

1. You set your OSC at 8Mhz. This is for your PIC. You must DEFINE OSC speed to the compiler also. Have DEFINE OSC 8.

2. For PIC16F690, SDA should be RB4 and SCL should be RB6.

hi.

why rb4 and rb6? i thought i2cwrite was 'bit banging' and it did not matter on which pin it is used???

i'm not using hardware i2c support. then is my connexion still wrong?

[xnihilo]

Sayzer,

There IS a
DEFINE OSC 8
in my program, i just forgot to paste it...

Here are some things i will have to check/do:

- solder a 8 pins socket on a protoboard instead of breadboard and solder connexions

- use 2k wpu only on sda instead of a 4.7k wpu on each scl and sda

- swap with another pic16f690 in case the one i use is defect

- swap with another 24lc08b in case the one i use is defect

- try a huge pause 50 instead of pause 5 after the i2cwrite in case it is a timing problem

- declare the eeprom address variable as a word instead of as a byte

- declare "eep_address" instead of "ep_address" (i wonder how i didn't see this typing error!)

- try to program a specific value in byte 0 of the eeprom using my pic-pg2 programmer and see if i get this value back with an i2cread

besides this i don't se what i can do...

[skimask]

- declare the eeprom address variable as a word instead of as a byte

See pages 7 and 10 of this datasheet:
http://ww1.microchip.com/downloads/e...Doc/21710H.pdf

EDIT: I get the feeling that you're doing a lot of 'thinking out loud' and not a lot of 'doing' (as indicated by the post below).
Not a good way to go about things...

[sayzer]

Sayzer,

There IS a
DEFINE OSC 8
in my program, i just forgot to paste it...

Here are some things i will have to check/do:

- solder a 8 pins socket on a protoboard instead of breadboard and solder connexions

- use 2k wpu only on sda instead of a 4.7k wpu on each scl and sda

- swap with another pic16f690 in case the one i use is defect

- swap with another 24lc08b in case the one i use is defect

- try a huge pause 50 instead of pause 5 after the i2cwrite in case it is a timing problem

- declare the eeprom address variable as a word instead of as a byte

- declare "eep_address" instead of "ep_address" (i wonder how i didn't see this typing error!)

- try to program a specific value in byte 0 of the eeprom using my pic-pg2 programmer and see if i get this value back with an i2cread

besides this i don't se what i can do...

How did you NOT get an error then?

Also, when you change your code after you asked some questions about it, it is difficult to follow.

Paste a new one with your modifications, so that we can see what the difference was.

[xnihilo]

"ep_address" instead of "eep_address" didn't generate an error because it is a paste error only. I selected the block starting from the 2nd chara of the line, so it is alright, the variable name is right.

I changed slightly the code:

eep_address VAR WORD
instead of BYTE

and:

I added:

ADCON0.0 = 0 'turn adcon off


Things I wanted to do:

- solder a 8 pins socket on a protoboard instead of breadboard and solder connexions
-> DONE

- use 2k wpu only on sda instead of a 4.7k wpu on each scl and sda
-> DONE, but I used 2K on each of the SCL and SDA pins

- swap with another pic16f690 in case the one i use is defect
-> DONE

- swap with another 24lc08b in case the one i use is defect
-> DONE

- try a huge pause 50 instead of pause 5 after the i2cwrite in case it is a timing problem
-> DONE

- declare the eeprom address variable as a word instead of as a byte
->DONE

- declare "eep_address" instead of "ep_address" (i wonder how i didn't see this typing error!)
-> DONE, no error there in fact

code is:

    'routine that checks if the external eeprom (the mag) is connected to the supplier
    'it writes than reads back the test value (33)
    checkwrite = 33
    eep_address = 0     'use storage byte 1 of 255 fo rthe test
    
    LCDOUT $fe,1,"CTRLbyte:",#eep_control
    PAUSE 2000
    
    I2CWRITE PORTC.6,PORTC.7,eep_control,eep_address,[checkwrite]    'store maxitem value in the mag external EEPROM
    PAUSE 50        'hadware dependent
    
    LCDOUT $FE,1,"Wrote:",#checkwrite,"@",#eep_address
    PAUSE 2000
    
    I2CREAD PORTC.6,PORTC.7,eep_control,eep_address,[checkwrite]    'store maxitem value in the mag external EEPROM
    
    LCDOUT $fe,1,"Read:",#checkwrite,"@",#eep_address
    PAUSE 2000
    
    IF (checkwrite != 33) then
        LCDOUT $fe,1,"couldn't write"
        PAUSE 4000
        checkwrite = 0
        GOTO endofroutine
    ENDIF
    checkwrite = 66

----------------------


RESULTS:

The output on LCD is:

"wrote:33@0"
"read:0@0"
"couldn'twrite"


So, back to the starting point but this time I have no idea what I could change.
Is it the wires length? Did I failed to set some registers? ...
I'm lost... And angry.
My circuit is useless if I can't write to external eeprom...

[skimask]

And pin 7 on the eeprom is connected to _______________

[mister_e]

EEP_ADDRESS MUST be a byte... Something change in the ControlByte when you want to access the other EEPROM Page (Banks). Page 6 of the above data sheet

One more, you haven't disable AN<9:8> yet, and it's your I2C lines... check ANSELH settings.... probably THE MAIN reason why you always have 00 as results. If it was the WP pin of the EEPROM, you would probably have FF all the time. if the device is already blank.

[xnihilo]

And pin 7 on the eeprom is connected to _______________

to gnd of course. i do not want to write protect the chip.