How to drive the Vinculum VDIP1 in UART mode

Closed Thread
Results 1 to 40 of 42

Hybrid View

  1. - 30th January 2010, 13:12 #1
    Bogs1217's Avatar
    Bogs1217
    Bogs1217 is offline Junior Member
    Join Date
    Jan 2010
    Posts
    4

    Did you find this post helpful? Yes | No

    Default

    Hi Dave,

    I can not share it right now, its a bit of confidential, not until of course after I finish it. I'll share it soon. Thanks a lot!

    Best regards!
  2. - 30th January 2010, 14:18 #2
    mackrackit's Avatar
    mackrackit
    mackrackit is offline SuperMod
    Join Date
    Nov 2003
    Location
    Wellton, U.S.A.
    Posts
    5,924

    Did you find this post helpful? Yes | No

    Default

    Ok...
    I was just wondering. I see so many say they are working on a school project. I can get that.
    But when someone says they are working on a thesis I have always wondered how hardware and the "basic" code that all came from some place else works in.

    Do not get me wrong. I am not saying you are copying anything and maybe this is just a small part of a larger project.

    Good luck!!!

    Maybe you and newbie from the other thread can get together...
    Dave
    Always wear safety glasses while programming.
  3. - 31st January 2010, 03:17 #3
    Bogs1217's Avatar
    Bogs1217
    Bogs1217 is offline Junior Member
    Join Date
    Jan 2010
    Posts
    4

    Did you find this post helpful? Yes | No

    Smile

    Hi Dave,

    Yes it was just a little part of the whole, I just need to make that module work. I've been doing my research for about a year now, and I was already implementing it.

    Thanks!

    And oh! I am not interfacing the module to a PIC microcontroller.
    Last edited by Bogs1217; - 31st January 2010 at 03:20.
  4. - 31st January 2010, 04:29 #4
    mackrackit's Avatar
    mackrackit
    mackrackit is offline SuperMod
    Join Date
    Nov 2003
    Location
    Wellton, U.S.A.
    Posts
    5,924

    Did you find this post helpful? Yes | No

    Default

    I get it now..

    Again, good luck! Glad I could help.
    Dave
    Always wear safety glasses while programming.
  5. - 26th February 2010, 02:25 #5
    page101's Avatar
    page101
    page101 is offline Junior Member
    Join Date
    Feb 2010
    Posts
    2

    Did you find this post helpful? Yes | No

    Thumbs up Question

    Hello guys, I've been searching around, and finally got here. I am also using VDIP1.

    Does anyone tried to send a file from the USB flash drive to the Microcontroller?
    I am trying to get a file from my flash drive, a jpg file and I wanted to send it to the monitor or to the UART of the VDIP1. I guess I am having a difficulty which command I will use. I tried to use "RD" command to send the whole content of the JPG file and got lots of values and it lasts for about 10 mins to finish and my VDIP1 hangs up after it so I need to restart it.

    And lastly I want to send again the jpg file to the UART of VDIP1 and send it to my flash drive. I can do it for txt file but that involves four steps, OPW, WRF, Content, CLF. I want to try different file types and not anymor txt files.

    Does anyone knows what to do about these or just an experience relating to these??? Thanks
  6. - 13th April 2010, 05:09 #6
    madhur's Avatar
    madhur
    madhur is offline Junior Member
    Join Date
    Mar 2010
    Posts
    4

    Did you find this post helpful? Yes | No

    Angry

    Hi.I am pre-final year engineering student from India.
    Our project is to copy data from one USB stick to another without use of PC.
    I searched a lot about it and I found that VNC1L is suitable for that.
    But i don't know from where i should start?
    Can anyone please help me??
  7. - 13th April 2010, 05:18 #7
    mackrackit's Avatar
    mackrackit
    mackrackit is offline SuperMod
    Join Date
    Nov 2003
    Location
    Wellton, U.S.A.
    Posts
    5,924

    Did you find this post helpful? Yes | No

    Default

    I tried helping a couple of others get started on the same thing here
    http://www.picbasic.co.uk/forum/showthread.php?t=10241
    I do not know if they had any luck, you might contact them and see.

    I wonder if all of you attend the same school? Seems to be a common homework assignment these days.
    Dave
    Always wear safety glasses while programming.
  8. - 18th May 2010, 02:27 #8
    ANANT PAL's Avatar
    ANANT PAL Guest

    Did you find this post helpful? Yes | No

    Smile

    hey, can you send me the circuit how you connected VDIP1 to PIC ?

    Quote Originally Posted by page101 View Post
    Hello guys, I've been searching around, and finally got here. I am also using VDIP1.

    Does anyone tried to send a file from the USB flash drive to the Microcontroller?
    I am trying to get a file from my flash drive, a jpg file and I wanted to send it to the monitor or to the UART of the VDIP1. I guess I am having a difficulty which command I will use. I tried to use "RD" command to send the whole content of the JPG file and got lots of values and it lasts for about 10 mins to finish and my VDIP1 hangs up after it so I need to restart it.

    And lastly I want to send again the jpg file to the UART of VDIP1 and send it to my flash drive. I can do it for txt file but that involves four steps, OPW, WRF, Content, CLF. I want to try different file types and not anymor txt files.

    Does anyone knows what to do about these or just an experience relating to these??? Thanks
  9. - 20th May 2010, 18:58 #9
    Jacques's Avatar
    Jacques
    Jacques is offline Junior Member
    Join Date
    May 2010
    Posts
    5

    Did you find this post helpful? Yes | No

    Default VDIP Doesnt connect to flash drive

    Hi Guys, I have a issue which is driving me nuts...

    When I connect either one of my flash drives to the VDIP module, nothing happens...

    When I apply VCC 5V to the device the leds blinks alternating then stops this happens when i start the module in spi or FIFO mode with or witout my flash drives. However when i start the module in UART the led's blinks continuously even when i connect my flash drives.

    1) Both my flash drives are not working with the VDIP, because they work perfectly on the pc
    2) my VDIP is blown, but also unlikely because i can re flash is using my rs323rl board.

    Does anyone had this led issue or what to do when vdip does not recognize your flash drives.

    Help will be greatly appreciated
« Previous Thread | Next Thread »

Similar Threads

  1. VDIP1 (Vinculum - FTDI) problems
    By BrianT in forum mel PIC BASIC Pro
    Replies: 12
    Last Post: - 20th August 2013, 13:51
  2. MPASM Path & File Name Length Limtation
    By Brian J Walsh in forum mel PIC BASIC Pro
    Replies: 7
    Last Post: - 14th June 2008, 15:48
  3. Oscillator stops when touching with a wire
    By Wilbert Ingels in forum mel PIC BASIC Pro
    Replies: 23
    Last Post: - 25th April 2008, 08:51
  4. USB-FTDI[UM232R] with PIC16f877a
    By bjox in forum USB
    Replies: 1
    Last Post: - 23rd February 2008, 22:40
  5. PIC newbie - took ages to program and i still have bugs
    By Trickae in forum mel PIC BASIC
    Replies: 14
    Last Post: - 26th September 2007, 05:41

Members who have read this thread : 0

You do not have permission to view the list of names.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules