Very Simple ICSP Programmer

Closed Thread
Results 1 to 40 of 130

Hybrid View

  1. - 6th May 2010, 00:00 #1
    togum2000's Avatar
    togum2000
    togum2000 is offline Junior Member
    Join Date
    May 2010
    Posts
    2

    Did you find this post helpful? Yes | No

    Default

    I have Problems of error in winpic, the programmer that I use is JDM2, I mounted 4 models jdm of different authors from the web, all the same error.

    Operating system Microsoft Windows XP Professional
    Version 5.1.2600 Service Pack 3 Compilation 2600
    I model of the system KM400-8235
    Processor x86 Family 6 Model 7 Stepping 0 AuthenticAMD ~1100 Mhz
    Total physical memory 512,00 MB
    Available physical memory 300,13 MB
    Total virtual memory 2,00 GB
    Available virtual memory 1,96 GB
    I space of the pagination file 1,22 GB

    Wx Pic

    15:29:48.187 Info: Loading definitions for "PIC16F84A" from C:\Arquivos de programas\WxPic\devices.ini .
    15:29:48.187 Info: PIC16F84A added and tested by FENG3
    15:29:48.187 Parsed "C:\Arquivos de programas\Microchip\MPLAB IDE\Device\PIC16F84A.dev" : found 10 bit combinations in 4 configuration bit groups .
    15:29:48.390 Initialising PIC-Programmer: Success.
    Testing: delay(500ms) took 0.50 seconds, timer_freq=3.5795 MHz ... ok
    15:31:39.765 Programming...
    15:31:39.765 Erasing ("bulk" or "chip") ...
    15:31:40.218 Programming and Verifying CODE, 0x000000..0x000121
    15:31:40.437 Verify Error: 000000: read 003FFF, wanted 00018C
    15:31:40.453 Verify Error: 000001: read 003FFF, wanted 00019D
    15:31:40.468 Verify Error: 000002: read 003FFF, wanted 00018F
    15:31:40.484 Verify Error: 000003: read 003FFF, wanted 000190
    15:31:40.546 Verify Error: 000004: read 003FFF, wanted 000191
    15:31:40.562 Verify Error: 000005: read 003FFF, wanted 000192
    15:31:40.578 Verify Error: 000006: read 003FFF, wanted 000193
    15:31:40.609 Verify Error: 000007: read 003FFF, wanted 000194
    15:31:40.625 Verify Error: 000008: read 003FFF, wanted 000195
    15:31:40.640 Verify Error: 000009: read 003FFF, wanted 000196
    15:31:40.656 Verify Error: 00000A: read 003FFF, wanted 000198
    15:31:40.671 Verify Error: 00000B: read 003FFF, wanted 000199
    15:31:40.687 Verify Error: 00000C: read 003FFF, wanted 00019A
    15:31:40.703 Verify Error: 00000D: read 003FFF, wanted 001683
    15:31:40.718 Verify Error: 00000E: read 003FFF, wanted 003010
    15:31:40.734 Verify Error: 00000F: read 003FFF, wanted 000085
    15:31:40.750 Verify Error: 000010: read 003FFF, wanted 003000
    15:31:40.750 Programming aborted after 17 errors.
    15:31:40.953 Programming CONFIG, 0x002000..0x002007
    15:31:41.187 Verify Error: 002007: read 003FFF, wanted 003FF1
    15:31:41.406 ERROR: Programming FAILED !

    Simulate only ( Ignore Hardware )

    15:33:13.593 Info: Loading definitions for "PIC16F84A" from C:\Arquivos de programas\WxPic\devices.ini .
    15:33:13.593 Info: PIC16F84A added and tested by FENG3
    15:33:13.593 Parsed "C:\Arquivos de programas\Microchip\MPLAB IDE\Device\PIC16F84A.dev" : found 10 bit combinations in 4 configuration bit groups .
    15:33:13.796 Initialising PIC-Programmer: Success.
    Testing: delay(500ms) took 0.50 seconds, timer_freq=3.5795 MHz ... ok
    15:34:12.00 Programming...
    15:34:12.00 Erasing ("bulk" or "chip") ...
    15:34:12.00 Programming and Verifying CODE, 0x000000..0x000121
    15:34:16.578 Programming CONFIG, 0x002000..0x002007
    15:34:16.703 Programming finished, no errors.

    WinPic DL4YHF

    Info: Loading definitions for "PIC16F84A" from C:\Arquivos de programas\WinPic\devices.ini .
    Info: PIC16F84A added and tested by FENG3
    Parsed "C:\Arquivos de programas\Microchip\MPLAB IDE\Device\PIC16F84A.dev" : found 10 bit combinations in 4 configuration bit groups .
    Initialising PIC-Programmer: Success.
    Testing: delay(500ms) took 0.50 seconds, timer_freq=3.5795 MHz ... ok
    Programming...
    Erasing ("bulk" or "chip") ...
    Programming and Verifying CODE, 0x000000..0x000121
    Verify Error: 000000: read 003FFF, wanted 00018C
    Verify Error: 000001: read 003FFF, wanted 00019D
    Verify Error: 000002: read 003FFF, wanted 00018F
    Verify Error: 000003: read 003FFF, wanted 000190
    Verify Error: 000004: read 003FFF, wanted 000191
    Verify Error: 000005: read 003FFF, wanted 000192
    Verify Error: 000006: read 003FFF, wanted 000193
    Verify Error: 000007: read 003FFF, wanted 000194
    Verify Error: 000008: read 003FFF, wanted 000195
    Verify Error: 000009: read 003FFF, wanted 000196
    Verify Error: 00000A: read 003FFF, wanted 000198
    Verify Error: 00000B: read 003FFF, wanted 000199
    Verify Error: 00000C: read 003FFF, wanted 00019A
    Verify Error: 00000D: read 003FFF, wanted 001683
    Verify Error: 00000E: read 003FFF, wanted 003010
    Verify Error: 00000F: read 003FFF, wanted 000085
    Verify Error: 000010: read 003FFF, wanted 003000
    Programming aborted after 17 errors.
    Programming CONFIG, 0x002000..0x002007
    Verify Error: 002007: read 003FFF, wanted 003FF1
    ERROR: Programming FAILED !

    Simulate only ( Ignore Hardware )

    Info: Loading definitions for "PIC16F84A" from C:\Arquivos de programas\WinPic\devices.ini .
    Info: PIC16F84A added and tested by FENG3
    Parsed "C:\Arquivos de programas\Microchip\MPLAB IDE\Device\PIC16F84A.dev" : found 10 bit combinations in 4 configuration bit groups .
    Initialising PIC-Programmer: Success.
    Testing: delay(500ms) took 0.50 seconds, timer_freq=3.5795 MHz ... ok
    Programming...
    Erasing ("bulk" or "chip") ...
    Programming and Verifying CODE, 0x000000..0x000121
    Programming CONFIG, 0x002000..0x002007
    Programming finished, no errors.

    WinPic800

    ERROR- Writing address 0x000000
    Written: 0x018C Read: 0x3FFF

    Icprog

    Verify Failed at address 0000h
  2. - 10th May 2010, 08:27 #2
    malc-c's Avatar
    malc-c Guest

    Did you find this post helpful? Yes | No

    Default JDM errors

    It does look like hardware issues. How are you connecting the JDM programmer.

    1) - USB to RS232 converters can be problematical and don't always work.
    2) - Serial ports on laptops (mainly older generations) tend not to be able to generate the voltages required to get the PIC into programming mode

    Are you selecting the correct chip in the Winpic options ?
    Have you tried Winpic800 (I'll let you google that one) or a different programmer that has support for JDM hardware.
  3. - 11th May 2010, 05:46 #3
    togum2000's Avatar
    togum2000
    togum2000 is offline Junior Member
    Join Date
    May 2010
    Posts
    2

    Did you find this post helpful? Yes | No

    Default

    Hello Malcolm


    I already tested all of the programs of Pic (Winpic, winpic800, wxpic, icprog,.... ) and all with the same problem, My Motherboard is a MSI KM4M-V ( VIA KM400+8237 Chipset ) the Processor is an AMD DURON 1.1Ghz. As to select the correct options of the chip, this everything correct. I hope somebody can help myself with the solution of the problem
  4. - 11th May 2010, 10:33 #4
    Gusse's Avatar
    Gusse
    Gusse is offline Member
    Join Date
    Dec 2007
    Location
    Finland
    Posts
    191

    Did you find this post helpful? Yes | No

    Default

    How much voltage you will have on MCLR/VPP pin when you enable Vpp (+13V) from Interface Test (Interface sheet)?
    With JDM and standalone PIC I have 10.4V and with ICSP (PIC on applicatio board) 9.3V and it is still working. Sometimes ICSP needs more flashing trials to avoid errors. I think it is because of lower VPP voltage..., but not sure.
    When it says "Initialising PIC-Programmer: Success." is should have all setting correct.

    BR,
    -Gusse-
« Previous Thread | Next Thread »

Similar Threads

  1. Melabs U2 Programmer Command Line Options
    By Robert Wells in forum General
    Replies: 5
    Last Post: - 3rd July 2009, 03:11
  2. Soic Icsp
    By earltyso in forum mel PIC BASIC Pro
    Replies: 4
    Last Post: - 13th September 2008, 20:51
  3. Need a programmer? And, ICSP - Effects on rest of circuit?
    By Rifraf in forum Schematics
    Replies: 1
    Last Post: - 11th December 2007, 00:57
  4. problems with USB programmer
    By malc-c in forum General
    Replies: 7
    Last Post: - 10th May 2007, 21:14
  5. USB programmer problems
    By uiucee2003 in forum USB
    Replies: 2
    Last Post: - 16th August 2006, 00:47

Members who have read this thread : 0

You do not have permission to view the list of names.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules