How to use Arrays Using Pic Basic Pro(need help)

[mister_e]

I agree, in general it's a good idea, but like beer, when used with moderation

Not bad...

PORTB=0 : LATB=0 : TRISB=0
    '    OR
SELECT CASE Pouet
    CASE 1 : Gosub MarryHadALittleBoy
    CASE 2 : Gosub DoSomethingElse
    '
    END SELECT

But erm...

CounterA=0 : CounterB = 1234 : TRISB = 0 : OPTION_REG=%10101010 : LCDOUT $FE,1,"Hello dear!" : Gosub KindaLongLine : IF A=0 then : V=1234 : ELSE : q=908 : ENDIF : GOSUB ItsReallyReallyLongNow : PORTA=128 : PORTC=144 : PAUSE 150 : I2CREAD SDA, SCL, ControlByte, Address, [$FF,$EA, 1,2,3,4,5,6,7,8,9,CounterA, CounterB,0,0,0] : LCDOUT $FE,$C0,"Ok i think you see the picture now" : Gosub OKImDone ' Startup thingy :o)

that's a bit too much, not sure if it compile anyway

I don't remind if that syntax was available on that one... ;o}


That's the whole kit with the speech synthesizer module, but without the tape deck... nostalgic now :-(

[Archangel]

I agree, in general it's a good idea, but like beer, when used with moderation

[/img]

I never could get one of those to work . . . could't find the ANY Key
EDIT: DOH TI90 either

[MrSafe]

I still can not get the arrays to work. Look at my program to see what I am doing wrong I haven't tried the other suggestions yet but I will get started on those as soon as i figure out the arrays.

[MrSafe]

In the program when i do

lcdout #key it shoots out the key correctly on the lcd however

when i use

htxt(x) = #key

it says bad expression when i try to compile

also when i use

htxt(x) = key

it works fine however it displays a blank spot on the lcd

[skimask]

In the program when i do
lcdout #key it shoots out the key correctly on the lcd however
when i use
htxt(x) = #key
it says bad expression when i try to compile
also when i use
htxt(x) = key
it works fine however it displays a blank spot on the lcd

htxt(x) = key ------>>>>> lookup key , [ "0123456789ABCDEF" ] , htxt[x]
^get rid of^---------------^^^^^^ replace with ^^^^^^^^^^^

Your turn to figure out why assigning the variable 'key' to htxt(x) and trying to get the LCD to display what is effectively variable 'key' doesn't work.
What is the ASCII character equivalent to 'key', if 'key' = 1? if 'key' = 2? if 'key' = 65?

[MrSafe]

i see ill try thank you for the reply. If you don't mind could you give me an example of that a very simple version of it that I could run with. Im sorry for being so ignorant but arrays is brand spanking new to me.

Your turn to figure out why assigning the variable 'key' to htxt(x) and trying to get the LCD to display what is effectively variable 'key' doesn't work.
What is the ASCII character equivalent to 'key', if 'key' = 1? if 'key' = 2? if 'key' = 65?

I can do that quite effectively ahaha its this damn blasted arrays thats slowing me down I have entire codes already done for that portion its just that I want to be able to loop the message over and over but I need arrays to do that and the message is not predetermined it will be different depending on the user.

[skimask]

i see ill try thank you for the reply. If you don't mind could you give me an example of that a very simple version of it that I could run with. Im sorry for being so ignorant but arrays is brand spanking new to me.

I just did...