Holtek Decoder

[Bruce]

The attached code example will decode the Holtek HT640.

Download the Linx .PDF below for details of the 640 data
structure.

http://www.linxtechnologies.com/Docu...datastruct.pdf

[George]

Hey thanks Bruce exactly what I was looking for

[Bruce]

Hey George,

You're most welcome. It's pretty old, but it's simple & it works.

You can improve the synch bit check part by replacing it with this;

IF PBIT[0] <= PBIT[1] THEN Begin
IF PBIT[1] >= PBIT[2] THEN Begin
IF PBIT[2] <= PBIT[3] THEN Begin

And you can remove this part; IF Loops > 2 THEN Begin

I stripped a lot of code out before posting it, but missed that line. It's bits &
peices of a much larger program that was a first go at decoding the Linx
hand-held.

[richb20b]

Having spent a couple of hours decoding the output from a Holtek HT600 encoder (in a Micromark wireless burglar alarm system), using the voltage divider / sound card / audacity method, I decided to post the specs to save anybody else the trouble...

01 01 0 - 5 bit header
01 01 01 01 01 - A0 A1 A2 A3 A4
01 01 01 01 01 - A5 A6 A7 A8 A9 (note A5 doesn't exist and is always 01)
01 01 01 01 01 - NA AD11 AD12 AD13 AD14
01 01 01 - AD15 NA NA

As noted, there is no A5 pin on the chip - this results in 01 always being present in this field. I'm not sure what the final four bits do, they always seem to be 01.

Hope this helps. I'm hoping Bruce's code will decode this - otherwise I've got the info to write my own :-)

[richb20b]

Having spent a couple of hours decoding the output from a Holtek HT600 encoder (in a Micromark wireless burglar alarm system), using the voltage divider / sound card / audacity method, I decided to post the specs to save anybody else the trouble...

The pulse train looks like this:

01 01 0 - 5 bit header
01 01 01 01 01 - A0 A1 A2 A3 A4
01 01 01 01 01 - A5 A6 A7 A8 A9 (note A5 doesn't exist and is always 01)
01 01 01 01 01 - NA AD11 AD12 AD13 AD14
01 01 01 - AD15 NA NA

0 (pin pulled low) is encoded as 00
1 (pin pulled high) is encoded as 11
- (pin left floating) is encoded as 01

A[0-9] is the address pin (these are connected to DIP switches on my alarm), AD[11-15] are the data pins - these are connected to other switches corresponding to the data that should be sent. As noted, there is no A5 pin on the chip - this results in 01 always being present in this field. I'm not sure what the final four bits do, they always seem to be 0, 1, 0, 1.

Between A9 and AD11 there appears to be two sync bits. These appear to be always 01.

Hope this helps. I'm hoping Bruce's code will decode this - otherwise I've got the info to write my own :-)

[tekart]

Bruce,
Just wanted to thank you for posting that Holtek Decoder code. Really nice job and extremely well documented. I had a job up and running using the Linx CMD-KEY keyfob transmitter in minutes thanks to you. Much appreciated.
Guy

The attached code example will decode the Holtek HT640.

Download the Linx .PDF below for details of the 640 data
structure.

http://www.linxtechnologies.com/Docu...datastruct.pdf

[Bruce]

Hi Guy,

You're very welcome, and thank you too. I'm glad you found a good use for it.

Edit: If you ever need to create your own PIC chip to emulate the Holtek 8-bit encoder too, I posted a pretty cool project for the Crownhill Amicus board here http://www.myamicus.co.uk/content.ph...Remote-Control with code for one.

And PC software to control the PIC, so you have a PC-based encoder to control your PIC-based decoder. Pretty fun stuff...

[khong20]

the code work great.

i there i am newbie in this forum and also at Picbasic pro, i need help in this code as well. the other PIC cannot receive every single bits , pls help
thanks alot

CLEAR
@ device pic16F876A, HS_OSC, wdt_on, lvp_off, protect_off
DEFINE OSC 20

ADDRESS VAR WORD ' Holds 10-bit address
DAT_OUT VAR BYTE ' Holds 8-bit data byte
BITS VAR BYTE ' Bit index for address & data bit pointer
LOOPS VAR BYTE ' Loop var for encode routine
LEDGreen var PORTC.4

' Use this timing for a Holtek HT640 @3V, 390K osc resistor
LONGB CON 732 ' 732uS for long bit & inter-bit delay
SHORTB CON 382 ' 382uS for short bit & inter-bit delay

' Use this timing for a Holtek HT640 @5V, 390K osc resistor
'LONGB CON 861 ' 861uS for long bit & inter-bit delay
'SHORTB CON 431 ' 431uS for short bit & inter-bit delay

SYMBOL E_OUT = PORTB.5 ' Assign encoder data out (to RF module) pin here

' Bank 1 Hardware initialization
'OPTION_REG = 128 ' Pull-ups = off, GPIO.2 = I/O, prescaler to Timer1

' Bank 0 Hardware initialization
PORTB = 0 ' Data output to RF transmitter idles low
TRISB=%00000000 ' all outputs

' sending A#2#3#64 with MCS terminal turns ON relay #1 at address #2
' #3 is sent since the FCTN-RLY4-xxx has the upper 2 address bits of the
' 10-bit decoder address left open (floating).

MAIN:
;DEBUGIN 5000,MAIN,[WAIT("A"),ADDRESS.LOWBYTE,ADDRESS.HIGHBYTE,DAT_OUT]
ADDRESS = $31F '1100011111
DAT_OUT = $99 '10011001

ENCODE_640:
high LEDGreen

FOR LOOPS = 1 TO 8 ' 8 data packet bursts per transmit period
' to simulate user button presses. |
' now do synch period & synch bits _ __ _ __ _|
HIGH E_OUT : PAUSEUS SHORTB ' | | | | | | | | | |
LOW E_OUT : PAUSEUS SHORTB ' | | | | | | | | | |
HIGH E_OUT : PAUSEUS LONGB ' | | | | | | | | | |
LOW E_OUT : PAUSEUS LONGB ' | | | | | | | | | |
HIGH E_OUT : PAUSEUS SHORTB ' | | | | | | | | | | ADDRESS | DATA
LOW E_OUT : PAUSEUS SHORTB ' | | | | | | | | | | 10-BIT | 8-BIT
HIGH E_OUT : PAUSEUS LONGB ' | | | | | | | | | |
LOW E_OUT : PAUSEUS LONGB ' 14mS | | | | | | | | | |
HIGH E_OUT : PAUSEUS SHORTB '_____ | |_| |__| |_| |__| |
' SYNCH BITS |
' now encode/send address
FOR BITS = 0 to 9 ' send 10-bit address
IF ADDRESS.0[BITS] = 1 THEN ' a 1 indicates the address bit is floating. NOT 1
LOW E_OUT : PAUSEUS LONGB
HIGH E_OUT : PAUSEUS SHORTB
LOW E_OUT : PAUSEUS LONGB
HIGH E_OUT : PAUSEUS SHORTB
ELSE
LOW E_OUT : PAUSEUS SHORTB
HIGH E_OUT : PAUSEUS LONGB
LOW E_OUT : PAUSEUS SHORTB
HIGH E_OUT : PAUSEUS LONGB
ENDIF
NEXT BITS

' now encode/send data
FOR BITS = 0 to 7 ' 8-bit data
IF DAT_OUT.0[BITS] THEN
LOW E_OUT : PAUSEUS LONGB
HIGH E_OUT : PAUSEUS SHORTB
LOW E_OUT : PAUSEUS LONGB
HIGH E_OUT : PAUSEUS SHORTB
ELSE
LOW E_OUT : PAUSEUS SHORTB
HIGH E_OUT : PAUSEUS LONGB
LOW E_OUT : PAUSEUS SHORTB
HIGH E_OUT : PAUSEUS LONGB
ENDIF
NEXT BITS
LOW E_OUT ' start synch period @ start of 2nd data packet
PAUSE 14 ' 14mS to 15mS synch period
NEXT LOOPS ' Close loop
LOW E_OUT ' Disable transmitter (turn off carrier)

low LEDGreen
pause 1000
GOTO Main

END

[khong20]

Any Help Pls.. i does received the data but not what i set in

ADDRESS = $31F '1100011111
DAT_OUT = $99 '10011001

[shahidali55]

Try the HT648L. This will decode data from the HT640.
Just make sure you select the same address as the one selected on the encoder (HT640)

[Megahertz]

Just to make sure I am getting it correctly (Bruce's code), is the Frequency of the operation of Holtek 640 in the above example 79Khz (appx) ?