PCB Supplier

[Pic_User]

I got a Trojan Virus Scan Alert from McAfee when I went to the above Pelcore site.

But maybe that's just me?

Added Edit: Google says: "This site may harm your computer?"
Searched on george88 got 2,960 hits

[george68]

Hello,Pic user

Thank you very much for your attention for our site.Maybe that's only
from your computer because I can access to our website without any
virus remind.Anyway,we'll have our web administrator to check our
website again for that.

Thank you again for attention to our company.

Have a nice day!

[Pic_User]

Hi George,

Sorry, but the Virus Scan is updated to the last minute. It tells me there is a Trojan each time I click onto the Pelcore site.

Google gives a “This site may harm your computer” flag too.

I am sure it is just something your web administrator has added to check traffic or log where people have been or where they have gone. I would get them to remove anything that might scare the customers away.

Your company looks like a great place to get circuit boards made.
-Adam-

[savnik]

I got a Trojan Virus Scan Alert from McAfee when I went to the above Pelcore site.

But maybe that's just me?

Added Edit: Google says: "This site may harm your computer?"
Searched on george88 got 2,960 hits

I got the same alert

[george68]

Hello Pic-User,Savnik

Thank you very much for your attention to our website.I'm glad to
tell you that our website is now ok and can access without any
problem after checking by our administrator.I really appreciate your
kind remind and support to our company.Now,you can browse our website www.pelcore.com at any time without problem.Thanks!

Best regards,

George
Pelcore Electronics
Mail:[email protected]
Http://www.pelcore.com

[Pic_User]

Hi George,
There is no longer a warning from the virus checking software.

I first went to your site in 04-25-2006:
http://www.pcbstandards.com/forums/s...ead.php?t=2512
Found the warning, and stopped there.
There’s probably a lot customers that were scared away too.

Glad you have fixed the problem.
We would like to know what it was, if you know.

Does your company accept Eagle (*.brd) files directly?
-Adam-

[george68]

Hi George,
There is no longer a warning from the virus checking software.

I first went to your site in 04-25-2006:
http://www.pcbstandards.com/forums/s...ead.php?t=2512
Found the warning, and stopped there.
There’s probably a lot customers that were scared away too.

Glad you have fixed the problem.
We would like to know what it was, if you know.

Does your company accept Eagle (*.brd) files directly?
-Adam-

Hi,Pic-User

Thank you again for your confirmation to our website.After checking by
our administrator,it's a kind of code attached to our website which is
not freindly.Now,it has been deleted by our administrator.

For the pcb file format,we cannot read *.brd files.We prefer gerber format
files sent to us which is most convenient for us.Moreover,the files generated
from protel,powerpcb is also ok for us.If you have any other pcb format files,
it's better if you can convert them into the above format.

Best regards,

George
Pelcore Electronics
Mail:[email protected]
Http://www.pelcore.com

[T.Jackson]

That's the only problem with Eagle - it's non industry standard, most manufactures should be able to do everything except actually "drill" the boards if it has been designed in Eagle. I use variant of Protel for most of my designs, but I tend to do things in (metric)

[Ron Marcus]

That's the only problem with Eagle - it's non industry standard, most manufactures should be able to do everything except actually "drill" the boards if it has been designed in Eagle. I use variant of Protel for most of my designs, but I tend to do things in (metric)

I have found very few manufacturers who accept Eagle format. You have to convert them using the Gerber274 program in the CAM section. There is also an Excellon subroutine for the drill information. I have a guy in Utah who does my double sided boards, and we worked through the sequences. One wierd quirk with Eagle though...One of the files gets overwritten when doing multiple board layers. You need to do one layer, save it to a separate file, then do the next,or rename the files with top, bottom, etc. I would switch PCB programs, but I have more custom footprints than a Sasquatch fan club!

Ron

[savnik]

Hello Pic-User,Savnik

Thank you very much for your attention to our website.I'm glad to
tell you that our website is now ok and can access without any
problem after checking by our administrator.I really appreciate your
kind remind and support to our company.Now,you can browse our website www.pelcore.com at any time without problem.Thanks!

Best regards,

George
Pelcore Electronics
Mail:[email protected]
Http://www.pelcore.com

now it's ok