Free Project - 245 LED Display

[magu]

The led doesen`t blink coreclty. It toggle, then stay lit 3 sec, blink again and so on. Maybe the pic is not good or the crystal.?

[Luciano]

Hi Magu,

This the reason why we are testing with this LED 1 blink program.
With this program you can verify if the PIC and its 10 MHz crystal oscillator work.

Try that: (In order)

- On the socket of IC1 solder a 100nF capacitor between the pin 14 (VDD) and pin 5 (GND).
(You should already have one close to the PIC, solder a second one on the above pins).

- Test if the LED 1 blinks.

- Replace the two 22pF capacitors.

- Test if the LED 1 blinks.

- Replace the 10 MHz crystal.

- Test if the LED 1 blinks.

- Replace the PIC. (Program a new PIC with MBLINK.HEX).

- Test if the LED 1 blinks.

- Use a different +5V power supply. (Make one with a voltage regulator 7805).

- Test if the LED 1 blinks.

* * *

When you program the PIC with the program IC Prog follow the steps visible in picture below:

Do not modify the fuses which are automatically set by the file MBLINK.HEX.



The PIC is programmed OK only if the VERIFY step is successful!

Best regards,

Luciano

[magu]

I made o small board showd in the picture attach and it works fine but the led stay lit. doesen`t blink foverer. And the led with the res doese`nt need to be conneted to Ra3 ? . I can`t find the datasheet for the crystal....

[Luciano]

Hi Magu,

This circuit will work with our program MBLINK.BAS.



Please seek help locally, find a PIC expert in your country willing to help you.

Good luck!

Best regards,


Luciano

[magu]

Hi Magu,

This circuit will work with our program MBLINK.BAS.



Please seek help locally, find a PIC expert in your country willing to help you.

Good luck!

Best regards,


Luciano

ok i understand. i will buil this circuit and then i will give my results. best regards.

[Luciano]

Hi Trent,

Far as I'm concerned this thread has been completely hijacked with 4 pages of junk carrying
a user rating of 1.8 out of 5.

Yes, this is a bad habit. All this discourages people from posting.

I don't consider the cries for help to be even the slightest bit genuine. That's the sickening part.

There were three people reporting a problem with this project and indeed there was a problem
with the schematic and we managed to find it.

Are Magu's cries for help genuine?
In my opinion yes.

Look at the picture posted by Magu:


(Click to enlarge the picture).

CPU board: (Picture)

Magu is not an expert, the decoupling capacitors were added in
a second time despite this was the second board he made.

Display board: (Picture)

The alignment of the LEDs, transistors and resistors was done with
great care. (All the components were soldered perpendicular).

What are my conclusions?

Little theoretical knowledge, but good perseverance.
The same can be said for his posts in this thread.

* * *

I was able to help him to partially test the board he made.
I have never used PicBasic before and I have never developed anything
using PIC microcontrollers. All I know about PicBasic and PIC microcontrollers
is based on personal researches done while evaluating them.

This is why I had to suggest him to find somebody in his town
willing to help him program the chip and test the board.

Best regards,

Luciano

[magu]

i`m very sorry for the delay but i was in vacantion, later i will post the result of the PIC...

[magu]

you are the kindest man on this thread. IT FINALLYY WORKS !!! . the problem has when i buyed the 2 caps (22pF). They give me one 22pF and one 223pF . the 223pF it was the problem . Good bless you and have good luck in live.