Any Simple ASM interupt code examples out there?

[George]

The PIC is a 16F676 so it's pretty tight with code space and variables (have tried DT's code but it runs out of variables), I'm just trying to exit from a serin command where there is always noise coming into the port (AM reciever module) just to increment a timer - and turn device off after a predetermined time.

[mister_e]

Can you post your code here?

To me a PIC with a USART would be more interesting in this case.

[sougata]

Hi,

Even if you are not using interrupts the timer0 rollover (INTCON.2, T0IF) gets set. So you can periodically check if the flag is set. To get proper timeout your main body loop should not execute for more than the timer0 rollover period. Even if it does then you miss a few ticks but still get some dirty timing. So here is how it goes

    OPTION_REG = %11000111     ' SET PRESCALE HERE 256 (Datasheet PAGE 14)
    ' @4MHz AND PRESCALE TIMER0 ROLLSOVER IN ABOUT 65.5 mS
    TIME_COUNTER VAR WORD      ' MAY BE A BYTE ALSO
    
    INTCON = 0
    TIME_COUNTER = 0
    MAIN_LOOP:
    
    ' DO WHATEVER
    IF INTCON.2 = 1 THEN       ' CHECK IF TIMER ROLLED OVER
       INTCON.2 = 0            ' CLEAR THE HARDWARE FLAG
       TMR0     = 0            ' CLEAR TIMER0 IF YOU WISH
       TIME_COUNTER = TIME_COUNTER + 1 ' INCREMENT YOUR COUNTER
    ENDIF
       IF TIME_COUNTER > PRESET THEN QUIT_LOOP
       

    GOTO MAIN_LOOP
       
    QUIT_LOOP:
    
    ' TIME OVER DO WHATEVER

PRESET is hard coded. In your main routine when you receive a valid signal don't forget to clear (Reset) the timer_counter variable and any pending ticks i.e., INTCON.2
Hope this helps

[George]

Thanks sougata, that'll be a handy piece of code for some other timing projects of mine - I havn't used the timer in a project before, just a crude timing loop instead.

I need to interupt to get out of serin command when there is static on the line, tho I'll prolly end up using the RSSI on the module and squelch it, would just be nice to have done this as a sample for learning.

How do you put code snippets in the little box on this forum? Mine is pasted below sofar

@ DEVICE PIC16F676, INTRC_OSC_NOCLKOUT, MCLR_OFF, PROTECT_OFF, BOD_ON, CPD_OFF


Define OSCCAL_1K 1
DEFINE OSC 4

TRISA = %001000
TRISC = %000000


ANSEL = 0 'disable analog
T1CON = %00000100
VRCON = 0 ' A/D Voltage reference disabled
CMCON = 7 'Disable comparitor

timesw var PortA.5
gosw var PortA.3
stopsw var PortA.4
LED1 var PortA.0
timeset var byte
display var byte
'time var word
b0 var byte
b1 var bit
b2 var byte

clear
timeset = 1
PortA = 0
PortC = 0

Begin: 'start sequence

display = (1 << b0) - 1
PORTC = display
pause 100
if b0 < 7 then
b0 = b0 + 1
goto begin
Else
Pause 1000
b0 = 0
portC = b0
Endif

Start:

serin PORTA.3,0,1,time,["READY"], timeset, b1 'Read receiver
gosub disply

time:
if timeset = 0 then b1 = 0
PortA.0 = b1
goto start

disply:

display = (1 << timeset) 'Set display to be bar type
PORTC = display 'output LEDs
' PORTA.0 = b1

return

'INTERUPT_SNIP ON TIMING INTERUPT

' if b1 = 1 then
' time = time + 1
' else
' time = 0
' endif

' if time > 200 and b1 = 1 then
' time = 0
' timeset = timeset - 1
' endif

'RTN FRM INT

[George]

Any idea's on squelch circuit? I was thinking about using an LM358 opamp putting the RSSI and a threshold into one amp then the output of that (maybe thru a divider) to the input of the other amp alongside data to get a squelched output?

I think MELabs should modify their code for the serin timeout and supply a timeout feature that will timeout if the qualifier isn't met within the timeout period I realise this would be more difficult - but I've spent hours fluffing around on what should be such a simple project - monitoring an RF receiver and counting down the time - i can't exit from the serin cos the static noise on the line resets the timer in the serin command, i can't use Darryl's wonderful interupt file cos it chews up all my variables, i can use an asm interupt cos I'm not really advanced enough to figure it out. Hopefully the squelch will work albeit with what probably is a significant reduction in range.

I do like Mister_e's concept of looking at a USART - I might have a quick look in2 that before I build my squelch

[skimask]

Any idea's on squelch circuit? I was thinking about using an LM358 opamp putting the RSSI and a threshold into one amp then the output of that (maybe thru a divider) to the input of the other amp alongside data to get a squelched output?

I think MELabs should modify their code for the serin timeout and supply a timeout feature that will timeout if the qualifier isn't met within the timeout period I realise this would be more difficult - but I've spent hours fluffing around on what should be such a simple project - monitoring an RF receiver and counting down the time - i can't exit from the serin cos the static noise on the line resets the timer in the serin command, i can't use Darryl's wonderful interupt file cos it chews up all my variables, i can use an asm interupt cos I'm not really advanced enough to figure it out. Hopefully the squelch will work albeit with what probably is a significant reduction in range.

I do like Mister_e's concept of looking at a USART - I might have a quick look in2 that before I build my squelch

Definetely use the hardware USART...many advantages...not to mention you learn a bit about. A bit of a steep learning curve...not too bad though...
The op-amp...somehow I get the feeling that the op-amp idea will pick up just as much noise as the raw data stream itself and you'll be getting loads of false interrupts.

[George]

Just looking through the site here looks like HSERIN will give just as many if not more headaches - so might pass on that

[sougata]

Hi,

As far as I understood that you need to monitor the serial input lines for your system to get "READY" as your qualifier. You can always do the qualifier checking manually. Looking for a "R", if found then "E" if not then again "R" and so on. Thus you (your PIC) would not be sitting inside the receive subroutine. Also the b1 variable used in your code is a BIT variable. I have no idea how a bit variable is treated in the serin ?? Also your pseudo code for the interrupt makes no sense. I thought "time" was a label but your code increments it
Please give me a little more detail on the receiver module, a datasheet pointer perhaps and exactly what you are trying to achieve in plain english. 16F676 does not have a hardware USART. Using it saves you the headache of polling the serial pin quite often so that you don't miss a bit. But you need to use USART interrupt then.