Serout problem

[lerameur]

By preconditioning you mean making sure the internal circuitry lets say capacitor will be ready . As in ready I mean not empty or full as to give a 1 instead of a 0 or the other way. BUt is there a start bit ? How does it know where the data start and end. I guess there is not start bit like in network communication, the training session replaces that . As en example, lets say the pic chip receives the 8bit is needs, on the next eight bit, it misses out (for a reason or another) a bit, Will it be taking its eight bit on the next sequence or simply drop the whole byte ? this is what I meant by how does it know the end and start of a byte series. In networking a packet has a lot of overhead, here there is none of that.

k

[skimask]

By preconditioning you mean making sure the internal circuitry lets say capacitor will be ready . As in ready I mean not empty or full as to give a 1 instead of a 0 or the other way. BUt is there a start bit ? How does it know where the data start and end. I guess there is not start bit like in network communication, the training session replaces that . As en example, lets say the pic chip receives the 8bit is needs, on the next eight bit, it misses out (for a reason or another) a bit, Will it be taking its eight bit on the next sequence or simply drop the whole byte ? this is what I meant by how does it know the end and start of a byte series. In networking a packet has a lot of overhead, here there is none of that.

k

When you start training/preconditioning the receiver, you won't get much of a recognizable output, maybe half a byte here and there, with or without start or stop bits,...until the receiver is conditioned. Which is why I keep saying you have to train the receiver first and ignore that data, then send some sort of sync byte to get things going.

In this project's case, we don't need much of anything so far, but with data transmission, you'll need to figure out some sort of packet method of transferring data.

The TXPIC (and therefore transmitter) still sends start and stop bits. It's just that the receiver module doesn't care about any start or stop bits. The PIC (rather the program anyways) still sees the start and stop bits and acts on them accordingly (and remember, a start bit is a low, a stop bit is a high, so that's 50% 1's and 50% 0's, they even themselves out, just like they should with manchester encoding). It's the data in between that ends up encoded.
If the PIC SerIn starts to receive a byte in the middle of it, it won't get the right stop bit, and jump out. If the PIC SerIn statement somehow never receives a full 8 bits and a stop bit, same thing, it'll timeout and jump to whatever you tell it to go to.

I don't know how to explain it to you any farther except to tell you to get online like I told you to do awhile back and do some Google'ing on manchester encoding, 433 transmitter/receiver modules, figure out how they work, why they need to use manchester encoding, etc.
The idea really isn't that hard to wrap your head around. And once you figure it out, you'll be all over it.
JDG

[Agent36]

Hi,

I am having a couple of problems with the above code. I changed it so that I could run it on two 16f628 chips, this works with out any problems.
Happy that I could tx and rx I wanted to tx using a 12f675 chip and rx on a 16f628.

Changing the tx code for a 12f675 and compiling it gave no errors. The leds flash ok and when I put an led on the serout pin I see the data. When I tx the code to the rx 16f628 via a tx the rx wont respond. I then hardwired the 12f675 to the 16f628 removing the tx/rx, it still wont work.
Can someone please check my code or suggest why it wont work.
Here is the code;

@ DEVICE PIC12F675, INTRC_OSC_NOCLKOUT
' System Clock Options (Internal)
@ DEVICE PIC12F675, WDT_ON
' Watchdog Timer
@ DEVICE PIC12F675, PWRT_ON
' Power-On Timer
@ DEVICE PIC12F675, MCLR_OFF
' Master Clear Options (Internal)
@ DEVICE PIC12F675, BOD_OFF
' Brown-Out Detect
@ DEVICE PIC12F675, CPD_OFF
' Data Memory Code Protect
@ DEVICE PIC12F675, PROTECT_ON

'PICBASIC PROGRAM

ANSEL = 0
CMCON = 7
TRISIO =%001000


INCLUDE "modedefs.bas"


txout VAR GPIO.4 : Output txout : dataout VAR BYTE
ledcount VAR BYTE
led1 VAR GPIO.0 : Output led1 : led2 VAR GPIO.1 : Output led2
led3 VAR GPIO.2 : Output led3 : led4 VAR GPIO.5 : Output led4
key VAR GPIO.3 : Input key 'push button on gpio.3
'1K-10K resistor from portb.0 to ground (pulldown)
'push button is wired between portb.0 and +5v
'initial LED check
led1 = 1 : Pause 500 : led1 = 0 : led2 = 1 : Pause 500 : led2 = 0
led3 = 1 : Pause 500 : led3 = 0 : led4 = 1 : Pause 500 : led4 = 0

mainloop:

IF key = 0 Then 'button not pressed
GoTo mainloop
EndIF
IF key = 1 Then
Pause 50 'wait 50ms for switch to debounce then check again
IF key = 1 Then 'if it's still pressed, then increment the count
ledcount = ledcount + 1
dataout = $55 '($55 = manchester encoded $0)
'train the receiver by sending 5 each of the $55's, may need more
'just copy the line below to make it send out more characters
SerOut txout, n2400, [ dataout, dataout, dataout, dataout, dataout ]
EndIF
EndIF

IF ledcount = 0 Then 'all leds off
dataout = $66 'manchester encoded $5, use because $0 is reserved
SerOut txout, n2400, [ dataout ]
'may have to send data more than once depending on how well the receiver
'can capture the data. Shouldn't have a problem sending it once
led1 = 0 : led2 = 0 : led3 = 0 : led4 = 0
EndIF

IF ledcount = 1 Then '1st led on
dataout = $56 'manchester encoded $1
SerOut txout, n2400, [ dataout ]
led1 = 1 : led2 = 0 : led3 = 0 : led4 = 0
EndIF

IF ledcount = 2 Then '2nd led on and so on and so on down the line....
dataout = $59 'manchester encoded $2
SerOut txout, n2400, [ dataout ]
led1 = 0 : led2 = 1 : led3 = 0 : led4 = 0
EndIF

IF ledcount = 3 Then
dataout = $5a 'manchester encoded $3
SerOut txout, n2400, [ dataout ]
led1 = 0 : led2 = 0 : led3 = 1 : led4 = 0
EndIF

IF ledcount = 4 Then
dataout = $65 'manchester encoded $4
SerOut txout, n2400, [ dataout ]
led1 = 0 : led2 = 0 : led3 = 0 : led4 = 1
EndIF

IF ledcount = 5 Then 'reset led count, roll it back to 0
ledcount = 0 'and turn leds off since count is back to 0
dataout = $66 'manchester encoded $5 (same thing as ledcount = 0 above)
SerOut txout, n2400, [ dataout ]
led1 = 0 : led2 = 0 : led3 = 0 : led4 = 0
EndIF

GoTo mainloop

End

I am using the two 16f628's with internal clock selected with no problem

thanks Nick

[skimask]

The internal clock on the 12F675 is probably too far off (i.e. 12F675 transmitting at 2350 baud, 16F628 receiving at 2400 baud, something like that).
Try slowing down the baud rate or moving the OSCCAL value on the 12F675 around a bit and see what happens.

[mister_e]

If the calibration data is still intact, you try to add

DEFINE OSCCAL_1K 1

Before ANSEL=0

[Agent36]

Hi,
thanks for the replys, I thought it might be something to do with the internal osc. Tried the program code on a 16f819 worked fine.
So i got a brand new 12f675, checked the osc cal and band gap values, loaded the code and rechecked them. I did this because I have had other timing issues with these 12f675's. Some of which were down to me I think.
I like to stick with an 8 pin chip because I aim to fit the board into a keyfob, so space is tight.
First I will try the soloutions you have offered.

Thanks for your time.

Nick

[Agent36]

Hi,

Thanks for the info regarding the DEFINE OSCCAL_1K 1
Adding that to the program code has solved my little problem.

I have found referances about this define in the pbp manual, for some reason I thought that DEFINE OSC 4mhz was correct.

I assume that DEFINE OSCCAL_1K 1 means

org 0
movwf OSCCAL

Thanks for your time........Nick