USART Stops Receiving Characters

[sayzer]

Any scheme to post here?
PIC #
Osc Type and speed, crystal

It is good to see that it is not only me still using traditional ways, even very ancient ways, to find answers.

But Steve, may be your CrystalBall have limited data base.

I use the Genie in the picture and I get anything I ask her!
The bad thing is that I can only ask three questions per weekend!



----------------------------------

[mister_e]

time for a change

Just ask here to have more than 3/week... it's still a wish

[breesy]

PIC18F2525 running at 20Mhz with a ceramic resonator.

The Rx line is fed directly from the XBee Tx, Tx (if relevent) goes through a voltage divider to give 3.3v input to the XBee..

Initialisation:

DEFINE OSC 20

' ---- Setup Hardware for USART ----
DEFINE HSER_BAUD 9600
DEFINE HSER_RCSTA 90h
DEFINE HSER_TXSTA 24h
DEFINE HSER_CLROERR 1

' ---- Setup Hardware for ADC ----
DEFINE ADC_BITS 8 ' Set number of bits in result
DEFINE ADC_CLOCK 3 ' Set clock source (rc = 3)
DEFINE ADC_SAMPLEUS 20 ' Set sampling time in microseconds

INCLUDE "variables.bas" 'Define Variables

' ---- Initialisation ----
Init:
Pause 10 'Safe Start Up Delay

ADCON1 = 14 ' All pins are digital, except AN0 (RA0)
CMCON = 7 ' Turn off comparators
INTCON2.7 = 1 ' Turn off PORT B pull ups

'Timer 0 is used for Input Pulse Measurement
TMR0L = 0 'clear Timer 0 low byte
T0CON = %11000101 'prescale = /64
INTCON.5 = 0 'disable TMR0 interrupt

'Timer 1 is used for the internal game clock
T1CON.4 = 1
T1CON.5 = 1 '8 prescaler
TMR1ON = 0 'Stop the timer, enable once game running

'Timer 2 is used for HPWM, is it really?

Init_Ports:
TRISA = %00000000
TRISB = %00000000
TRISC = %00000000

PORTA = %00000000
PORTB = %00000000
PORTC = %00000000

Input Rx
Output Tx

Input Serial_In
Input Menu
Input Battery
Input Mercury

'No PWM output when pin is input
Input Backlight
HPWM 1,50,40000

Output Serial_Out
Low Serial_Out
Init_Proceedure:

For i = 0 To 200
Pause 1
Next i

GoSub Update_LED
GoSub Update_LCD

HSEROUT ["+"]

Init_Interrupts:
RCIE = 1 'Enable USART Rx Interrupt
TMR1IE = 1 'Enable Timer 1 Interrupt
INTCON2.6 = 0 'INT0 on Falling Edge
INTCON = %11010000 'Global, Peripheral, INT0 Enable

ON Interrupt Goto Interrupt_Handler

Main_Loop:

If Menu Then
Input Backlight
Else
Output Backlight
EndIf

'Motion, Report If Requested.
If (Report_Mercury = 1) AND (Status_Mercury <> Mercury) Then
Report_Mercury = 0
Status_Mercury = Mercury

HSEROUT ["F"]
EndIf

Goto Main_Loop


Interrupt:

' ---- Interrupts ----

DISABLE

Interrupt_Handler:
If RCIF Then Goto Int_Rx
If INT0IF Then Goto Int_Hit
If TMR1IF Then Goto Int_Time

Interrupt_Exit:
INT0IF = 0
While RCIF
t = RCREG ' trash leftovers to clear RCIF before return
Wend
RESUME

'-------

Int_Rx:
If RCSTA.1 Then
HSEROUT ["Overrun"]
Pause 6
EndIf

HSERIN 1, Interrupt_Exit, [PacketID, PacketCheckSum, str Buffer\20\Sentinel]
CheckSum = 0

If PacketID > 0 Then
For i = 0 To 20
CheckSum = CheckSum + Buffer[i]
Next i
EndIf

If (PacketID > 0) AND (PacketCheckSum != (255 - CheckSum)) Then 'Failed To Receive Correctly
HSEROUT ["\", PacketID]
Pause 6
Else
Select Case Buffer[0]
'Do Stuff
End Select

Pause 6
HSEROUT ["/", PacketID]
Pause 6
EndIf


Goto Interrupt_Exit


[keithdoxey]

Does it work if you remove the wireless link and have a direct cable connection?

If not then there is a code problem with the PIC

If it works then for some reason the radio link is dying.

[Archangel]

PIC18F2525 running at 20Mhz with a ceramic resonator.


INCLUDE "variables.bas" 'Define Variables

Hi Breezy,
no one can compile without variables.bas
JS

[breesy]

Hi,

Problem solved with addition of 33pF cap between the line and ground..

I am at a loss to explain why... Could there have been a high frequency ripple that I could not see on the scope since the probe is arresting it?