pot command

[peterdeco1]

Hi Lerameur. I have an 'F88 and this program works. The 'F88 has 5 ADC's which are better than using the pot command. I connected pin 17 (ana 0) to the center terminal of a 1 meg pot. The CCW terminal to ground, CW terminal to B+.

OSCCON = $60 'SET INT OSC TO 4MHZ
ANSEL = 0 'SELECT ANALOG INPUTS 0 = NONE AND ALL DIGITAL
ADCON0 = 0 'AD MODULE OFF & CONSUMES NO CURRENT
CMCON = 7 'COMPARATORS OFF
TRISA = %11111111 'PORTA INPUTS
TRISB = %00000000 'PORTB OUTPUTS
X VAR BYTE 'VARIABLE TO PUT POT VALUE
PORTB = 0 'ALL OUTPUTS LOW

START:
ADCIN 0, X 'READ VALUE ON ANA 0
IF X > 0 AND X <= 50 THEN LED1
IF X > 50 AND X <= 100 THEN LED2
IF X > 100 AND X <= 200 THEN LED3
IF X > 200 THEN LED4
GOTO START

LED1:
HIGH PORTB.0
PAUSE 1000
LOW PORTB.0
GOTO START

LED2:
HIGH PORTB.1
PAUSE 1000
LOW PORTB.1
GOTO START

LED3:
HIGH PORTB.2
PAUSE 1000
LOW PORTB.2
GOTO START

LED4:
HIGH PORTB.3
PAUSE 1000
LOW PORTB.3
GOTO START

[lerameur]

I am going to try this today thanks.
I am following John Iovine,s book, he usesa F84a pic. He always uses the portB by default, I wanted to try using port A , but on a F88.
Also I was reading the command CMCON=7 meaning th three first bit are set to one. When I read the legend it says 1 is for Setting th bit, I would of first thought setting would be for setting for comparator mode.

k

[Archangel]

I am going to try this today thanks.
I am following John Iovine,s book, he usesa F84a pic. He always uses the portB by default, I wanted to try using port A , but on a F88.
Also I was reading the command CMCON=7 meaning th three first bit are set to one. When I read the legend it says 1 is for Setting th bit, I would of first thought setting would be for setting for comparator mode.

k

Hi Lerameur,
I have his book too, I thought that was where you got that code. He , in my opinion, left too many loose ends in his code as he neglected to put in all the needed little setup routines, like the trisa and trisb etc. he relies on pbp defaults
and that sorta leaves beginners out in the cold, if you do not rely on defaults and write in everything your code will always be usable and only require minor tweaking to port to other PICs
Cheers
JS

[lerameur]

yes thats what I am beginning to realize too , lots of stuff missing in the book, then when you use another chip, I'm screwed.
Abou tthe A/D, doesn't that read a voltage ? whereas the Pot read a resistance ?

[lerameur]

both cde works,
i am trying to figure out one thing now.

I am replacing this command line:
HIGH PORTB.0
PAUSE 1000
LOW PORTB.0

by this one:
serout 2,n9600,(2)

i am getting errors:
C:\PBP\POT_TRY.BAS ERROR Line 39: Bad expression.
C:\PBP\POT_TRY.BAS ERROR Line 33: ID LED2 is not a LABEL.
C:\PBP\POT_TRY.BAS ERROR Line 34: ID LED3 is not a LABEL.
C:\PBP\POT_TRY.BAS ERROR Line 35: ID LED4 is not a LABEL.

suddenly my labels are not labels ??

[keithdoxey]

Sometimes the error messages bear no relation to the actual error.

Try changing serout 2,n9600,(2)

to serout 2,n9600,[2]

[lerameur]

yes thanks,

those french keyboards...

k