mixing joy stick

Closed Thread
Results 1 to 18 of 18
  1. - 15th October 2008, 23:21 #1
    Macgman2000's Avatar
    Macgman2000
    Macgman2000 is offline Member
    Join Date
    May 2008
    Posts
    169

    Question mixing joy stick

    I have 2 pots that I am trying to mix at the TX side. The RX side drives standard hobby servos.

    If the joy stick is viewed as 4 compass directions. Moving the stick north and south moves the 2 servos in unison the same amount same direction. But going E and W only moves one that corresponds to East and one that corresponds to West.

    I have tried IF then conditional statements with dead bands to detect the proper mixing conditions but it seems to fall out of these conditions because of the sloppy nature of the pot/joy stick mechanics.

    Does anyone have a cleaver way of finessing these issues?

    Nick
  2. - 16th October 2008, 02:42 #2
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    What is this? A V-tail mixer? Spoilerons?
    So, if your range is 0-999, the middle, say 400-600 from the stick is sloppy, and you need to assume that anything between 400 and 600 is actually 500, and need to 'linearize' the curve off of that 500 center some way leading back to the 'normal' values?
    Jeeze...does that make any sense at all?
  3. - 16th October 2008, 03:03 #3
    Macgman2000's Avatar
    Macgman2000
    Macgman2000 is offline Member
    Join Date
    May 2008
    Posts
    169

    Did you find this post helpful? Yes | No

    Default

    I have only 8bit payload per pot. Actually its like flapperons,I am steering a tank. so to go right it mixes left and right motors in proportions, to steer from large arc to tight arc. To go straight it moves the left and right motor in tandum, same with reverse.
  4. - 16th October 2008, 03:13 #4
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Macgman2000 View Post
    I have only 8bit payload per pot. Actually its like flapperons,I am steering a tank. so to go right it mixes left and right motors in proportions, to steer from large arc to tight arc. To go straight it moves the left and right motor in tandum, same with reverse.
    Ok, tank-tread-erons...
    I'll cook it over in the brain for awhile...
    So then, values run from 0 to 255, 128 in the middle, say +/-16 for slop? 112-144 = no movement? Something along those lines?

    EDIT: done cooking...

    Without some better math (i.e. more bits at the input side), you'll lose some range at the output side of things (i.e. 0-223 vs. 0-255)...
    Code:
    inputvalue var byte
outputvalue var byte
deadband var byte
deadband = 32

if ( input > ( 128 + ( deadband / 2 ) ) ) or ( input < ( 128 - ( deadband / 2 ) ) ) then
     output = 128   'set output to middle value
else
     if input > ( 128 + ( deadband / 2 ) ) then
          input = input - deadband
     endif
endif
    The total range is reduced to the max byte value (255) minus the total deadband (32 in this case) which equals 223, so 0=minimum, 223=maximum.
    But that's just one way to do it...
    Last edited by skimask; - 16th October 2008 at 03:52.
  5. - 16th October 2008, 04:29 #5
    Macgman2000's Avatar
    Macgman2000
    Macgman2000 is offline Member
    Join Date
    May 2008
    Posts
    169

    Did you find this post helpful? Yes | No

    Default

    ok i understand the way you did it. I tried the following and it was iffy.


    ;ADCIN1 mydata1 ; X pot L/R
    ;ADCIN2 mydata2 ;y pot FW/REV
    etc
    .
    if mydata1 > 120 and mydata1 < 130 then
    mydata2 = mydata1
    endif
    here TX out the byte.

    I am looking at the X pot to see if it has moved from center 120~130 if not then make Y the same as X so that left and right motor move in tandum going forward. If the X pot moves outside of the 120~130 range, then skip the conditional statement and load individual values for X and Y. the mechanical slop is so bad it is hard to find the deadband....I guess I need to do something mechanically to stabilize it....since I don't see how to improve it via code.
  6. - 16th October 2008, 04:34 #6
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    Ok, sure, now I smell what you're cooking... I was only shooting for a single channel, one X pot if you will.
    Let me cook on that a bit more... I'm sure it can be done the same way, just have to sort out the deadband issue. Maybe start huge and working your way down until it seems comfortable...
  7. - 16th October 2008, 04:43 #7
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    Code:
    lrinput var byte : frinput var byte : lroutput var byte : froutput var byte
loutput var byte : routput var byte : lrdeadband var byte : frdeadband var byte
lrdeadband = 32 : frdeadband = 32
lrmid var byte : lrmid = 128 - ( lrdeadband / 2 )
frmid var byte : frmid = 128 - ( frdeadband / 2 )
;adcin x
;adcin y

if ( lrinput > ( 128 + ( lrdeadband / 2 ) ) ) or ( lrinput < ( 128 - ( lrdeadband / 2 ) ) ) then
     lroutput = lrmid   'set output to middle value
else
     if lrinput > ( 128 + ( lrdeadband / 2 ) ) then
          lroutput = lrinput - lrdeadband
     endif
endif

if ( frinput > ( 128 + ( frdeadband / 2 ) ) ) or ( frinput < ( 128 - ( frdeadband / 2 ) ) ) then
     froutput = frmid   'set output to middle value
else
     if frinput > ( 128 + ( frdeadband / 2 ) ) then
          froutput = frinput - frdeadband
     endif
endif
    After this bit o' code, left and right should have the deadband taken out, with (in this case) the mid-point of left/right being at 112, and the forward/reverse midpoint is also at 112.
    Now you have to drive the H-bridge...
    What do you have setup for that? Or do you have a separate controller for it or what?
    Then you have to add in some code to find and/or remember the minimum and maximum values ever read for the pot's, sort of like a calibration routine for joysticks on a PC...blah blah blah...but I suppose you can keep adding tricks to the code until it gets unbearable...
  8. - 16th October 2008, 04:53 #8
    Darrel Taylor's Avatar
    Darrel Taylor
    Darrel Taylor is offline Fanatical Contributor
    Join Date
    Jul 2003
    Location
    Colorado Springs
    Posts
    4,959

    Did you find this post helpful? Yes | No

    Default

    Never had a Tank before. But it sounded like an interesting way to spend the evening.

    It might do it all. Or it might blow a loogie.
    Code:
    DeadBandX  CON 10      ; center mechanical Dead Area
DeadBandY  CON 5
JoyX       VAR BYTE    ; A/D values from joystick
JoyY       VAR BYTE
TrimX      VAR BYTE
TrimY      VAR BYTE
Xcorr      VAR WORD    ; corrected values (x-128)
Ycorr      VAR WORD    ;   puts center at 0,0
Left       VAR WORD    ; Left Tread
Right      VAR WORD    ; Right Tread
LeftDir    VAR BIT     ; Tread directions  1 = backwards
RightDir   VAR BIT

Main:
    ADCIN 0, JoyX                            ; get Joystick values
    ADCIN 1, JoyY
    ADCIN 2, TrimX                           ; Joystick Center trims
    ADCIN 3, TrimY                           ;  set to 128 if not used
    
    Xcorr = JoyX - 128 + (TrimX >> 3) - 16   ; adjust center position to 0
    Ycorr = JoyY - 128 + (TrimY >> 3) - 16
    IF ABS(Xcorr) < DeadBandX THEN Xcorr = 0 ; center deadband
    IF ABS(Ycorr) < DeadBandY THEN Ycorr = 0

    Left  = Ycorr + Xcorr                    ; Mix Tread speeds 
    Right = Ycorr - Xcorr
     
    LeftDir = Left.15                        ; Tread Direction
    RightDir = Right.15                      ;  1 = backwards
    
    Left = ABS(Left)                         ; make values positive
    Right = ABS(Right)
    
    if Left > 127 then Left = 127            ; Clamp max outputs 
    if Right > 127 then Right = 127
    
    ; Drive motors here
    ; LeftDir indicates the direction of the Left tread
    ; Left is the Speed of the motor 0 - 127
    ; Same for Right Track
GOTO Main
    DT
  9. - 16th October 2008, 11:48 #9
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Darrel Taylor View Post
    Never had a Tank before. But it sounded like an interesting way to spend the evening.
    It might do it all. Or it might blow a loogie.
    What!?! You live in CA. and never had a tank?
    Slick bit of code...not nearly enough colons in there, but slick nonetheless... I'm hanging on to it for future use.
  10. - 20th October 2008, 21:37 #10
    Darrel Taylor's Avatar
    Darrel Taylor
    Darrel Taylor is offline Fanatical Contributor
    Join Date
    Jul 2003
    Location
    Colorado Springs
    Posts
    4,959

    Did you find this post helpful? Yes | No

    Default

    Here ya go ski. Is this better ...
    Code:
    ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
:DeadBandX  CON 10      ; center mechanical Dead Area                      :
:DeadBandY  CON 5                                                          :
:JoyX       VAR BYTE    ; A/D values from joystick                         :
:JoyY       VAR BYTE                                                       :
:TrimX      VAR BYTE                                                       :
:TrimY      VAR BYTE                                                       :
:Xcorr      VAR WORD    ; corrected values (x-128)                         :
:Ycorr      VAR WORD    ;   puts center at 0,0                             :
:Left       VAR WORD    ; Left Track                                       :
:Right      VAR WORD    ; Right Track                                      :
:LeftDir    VAR BIT     ; Tread directions  1 = backwards                  :
:RightDir   VAR BIT                                                        :
:                                                                          :
::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
:Main:                                                                     :
:    ADCIN 0, JoyX                            ; get Joystick values        :
:    ADCIN 1, JoyY                                                         :
:    ADCIN 2, TrimX                           ; Joystick Center trims      :
:    ADCIN 3, TrimY                           ;  set to 128 if not used    :
:                                                                          :
:    Xcorr = JoyX - 128 + (TrimX >> 3) - 16   ; adjust center position to 0:
:    Ycorr = JoyY - 128 + (TrimY >> 3) - 16                                :
:    IF ABS(Xcorr) < DeadBandX THEN Xcorr = 0 ; center deadband            :
:    IF ABS(Ycorr) < DeadBandY THEN Ycorr = 0 ;                            : 
:                                                                          :
:    Left  = Ycorr + Xcorr                    ; Mix Tread speeds           :
:    Right = Ycorr - Xcorr                                                 :
:                                                                          :
:    LeftDir = Left.15                        ; Tread Direction            :
:    RightDir = Right.15                      ;  1 = backwards             :
:                                                                          :
:    Left = ABS(Left)                         ; make values positive       :
:    Right = ABS(Right)                                                    :
:                                                                          :
:    if Left > 127 then Left = 127            ; Clamp max outputs          :
:    if Right > 127 then Right = 127          ;                            : 
:                                                                          :
:    ; Drive motors here                                                   :
:    ; LeftDir indicates the direction of the Left tread                   :
:    ; Left is the Speed of the motor 0 - 127                              :
:    ; Same for Right Track                                                :
:GOTO Main                                                                 :
::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
    Still compiles.
    DT
  11. - 21st October 2008, 00:09 #11
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    dx con 10:dy con 5:jx var byte:jy var byte:tx var byte:ty var byte:xc var word:yc var word:lt var word:rt var word:ld var bit:rd var bit
    main: adcin 0,jx:adcin 1,jy:adcin 2,tx:adcin 3,ty:xcr=jx-128+(tx>>3)-16:yc=jy-128+(ty>>3)-16:IF ABS(Xc) < dx THEN Xc = 0
    IF ABS(Ycorr) < dy THEN Ycorr = 0
    lt=yc+xc:rt=yc-xc:ld=lt.15:rd=rt.15:lt=abs(lt):rt=abs(rt):if Lt > 127 then Lt = 127
    if Rt > 127 then Rt = 127
    GOTO Main
    That's what I'm talkin' 'bout...
  12. - 21st October 2008, 00:57 #12
    Darrel Taylor's Avatar
    Darrel Taylor
    Darrel Taylor is offline Fanatical Contributor
    Join Date
    Jul 2003
    Location
    Colorado Springs
    Posts
    4,959

    Did you find this post helpful? Yes | No

    Default

    Eeeeuuuwww ...

    Cleanup on Isle #2

    <img src="http://www.picbasic.co.uk/forum/attachment.php?attachmentid=2403" />
    DT
  13. - 21st October 2008, 01:36 #13
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Darrel Taylor View Post
    Eeeeuuuwww ...
    Cleanup on Isle #2
    To quote somebody else...
    Maybe you want a:

    Cleaup on Aisle #2
  14. - 21st October 2008, 01:47 #14
    Darrel Taylor's Avatar
    Darrel Taylor
    Darrel Taylor is offline Fanatical Contributor
    Join Date
    Jul 2003
    Location
    Colorado Springs
    Posts
    4,959

    Did you find this post helpful? Yes | No

    Default

    No, I think you have your own little Island there.

    The Colon Isle.

    Population 1.
    DT
  15. - 21st October 2008, 02:01 #15
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Darrel Taylor View Post
    No, I think you have your own little Island there.
    The Colon Isle.
    Population 1.
    This Isle has been Colon-ized!
    Oh, and population 2.5 (got one that's just over half-way done cookin' in the oven)
  16. - 21st October 2008, 02:24 #16
    Darrel Taylor's Avatar
    Darrel Taylor
    Darrel Taylor is offline Fanatical Contributor
    Join Date
    Jul 2003
    Location
    Colorado Springs
    Posts
    4,959

    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by skimask View Post
    This Isle has been Colon-ized!
    Good one!

    Oh, and population 2.5 (got one that's just over half-way done cookin' in the oven)
    That makes it a "semi-colon" ...
    So it's commented out.
    -0.5
    DT
  17. - 21st October 2008, 03:22 #17
    skimask's Avatar
    skimask Guest

    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Darrel Taylor View Post
    Good one!
    That makes it a "semi-colon" ...
    So it's commented out.
    -0.5
    Well, it's my Isle...2 big hills, a valley, bushes, and a cavern not well tread upon...
  18. - 21st October 2008, 04:46 #18
    Andy Wood's Avatar
    Andy Wood
    Andy Wood is offline Junior Member
    Join Date
    Apr 2007
    Posts
    53

    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Darrel Taylor View Post
    Eeeeuuuwww ...

    Cleanup on Isle #2

    <img src="http://www.picbasic.co.uk/forum/attachment.php?attachmentid=2403" />
    Is this anything like colon cleansing???.......
« Previous Thread | Next Thread »

Similar Threads

  1. Parallax Memory Stick Datalogger using SPI
    By djmachine in forum mel PIC BASIC Pro
    Replies: 3
    Last Post: - 26th March 2009, 03:04
  2. Mixing basic and assembly
    By ManInMotion in forum mel PIC BASIC Pro
    Replies: 1
    Last Post: - 23rd September 2008, 09:48
  3. Displaying messages with only 7 (or 4) LEDs on a stick...
    By flotulopex in forum mel PIC BASIC Pro
    Replies: 15
    Last Post: - 20th May 2007, 08:35
  4. PBP and assembler mixing - weird goings-on?
    By Giulio in forum mel PIC BASIC Pro
    Replies: 2
    Last Post: - 13th November 2006, 21:17
  5. USB memory stick
    By Demon in forum mel PIC BASIC Pro
    Replies: 14
    Last Post: - 12th July 2005, 20:57

Members who have read this thread : 0

You do not have permission to view the list of names.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules