DSPIC Support

Closed Thread
Results 1 to 15 of 15

Thread: DSPIC Support

  1. - 19th February 2006, 03:09 #1
    GeoJoe's Avatar
    GeoJoe
    GeoJoe is offline Junior Member
    Join Date
    Feb 2006
    Location
    Arvada Colorado
    Posts
    31

    Default DSPIC Support

    I have been using PBP for only 5 months. I love the ease of use and so does my boss. I can crank out test fixtures, special controller orders, good user interfaces, etc... However, I can see the future. I will need DSPIC support sooner than later. I'll have to either wash the bad 'C' tasted out of my mouth or get the new version of PBP that supports DSP's. The huge growth of Microchip PIC MCU's would suggest that eventually MELabs will support 'ALL' of the PIC MCU's. Please please please (Shameless begging) support DSPIC's soon.
  2. - 19th February 2006, 07:43 #2
    Normnet's Avatar
    Normnet
    Normnet is offline Contributor
    Join Date
    Oct 2004
    Posts
    440

    Did you find this post helpful? Yes | No

    Default

    Anyone tried the following?

    Development board:
    http://www.circuit-ed.com/easydspic2.htm

    BASIC compiler for dsPIC towards bottom of page
    http://www.circuit-ed.com/product1.html

    Norm
  3. - 9th March 2006, 12:05 #3
    lab310's Avatar
    lab310 Guest

    Did you find this post helpful? Yes | No

    Default

    And what a rip-off that is...

    http://www.mikroelektronika.co.yu/en...ols/etools.htm

    http://www.mikroelektronika.co.yu/en...uct/compilers/
  4. - 9th March 2006, 18:59 #4
    languer's Avatar
    languer
    languer is offline Member
    Join Date
    Jul 2003
    Location
    USA - Arizona
    Posts
    156

    Did you find this post helpful? Yes | No

    Default

    Why is this exactly a rip-off? I see there's a 30% discount on the mikroelektronika site, but that only applies if you buy a development system with it.
  5. - 11th March 2006, 01:19 #5
    GeoJoe's Avatar
    GeoJoe
    GeoJoe is offline Junior Member
    Join Date
    Feb 2006
    Location
    Arvada Colorado
    Posts
    31

    Did you find this post helpful? Yes | No

    Default Rip off?

    Why is Mikro a rip off? It seems quite comperable to PBP. They have quite a few sweet features on the demo boards. Did you check out the demo software? I did only for a few minutes. It is very similar to PBP.

    I've been busting my hump and have not had time to fully investigate Mikro. I wish someone from PBP would respond or publish their intensions.
  6. - 13th March 2006, 08:38 #6
    lab310's Avatar
    lab310 Guest

    Did you find this post helpful? Yes | No

    Default

    You misunderstood me, I have nothing to say against Mikroelektronika, I was talking about circuit-ed site , as they are selling Mikroelektronika's board and compilers at prices 30-40% higher (169$ against 115$ for EasyPic3 board, for example). They are willing to give 30% discout on compilers withouth bying a developement board, just contact them by mail (at least they did that for me).
    I have 4 different boards and 2 compilers made by them, and they are extraordinary value for money. But be aware, transfering from PBP to Mikroelektronika's Basic is anything but straightforward, since M Basic has a more Pascal than Basic way of "thinking". Now, I only use there Basic for DSPic since there isn't any alternative on the current market, and for "regular Pics PBP and Proton. I would rate Mikroelektronika's development board a pure A, but compilers not more than B. ( just for comparasion, I would rate PBP with B and Proton with A)
    Last edited by lab310; - 13th March 2006 at 09:18.
  7. - 14th March 2006, 02:44 #7
    GeoJoe's Avatar
    GeoJoe
    GeoJoe is offline Junior Member
    Join Date
    Feb 2006
    Location
    Arvada Colorado
    Posts
    31

    Did you find this post helpful? Yes | No

    Default Dspic

    I see now Lab what you are saying. What type of development are you using these tools for? Are you developing any motor controllers or DC to DC converters? Have you used any touch screens for your projects?
    Have you used Hi Tech C? It is looking very attractive and robust. I'm thinking I MUST get familiar with C. www.htsoft.com
    Anyway thanks for the reply and the direction for MB. For the short term I'll still be using PBP and beating my head against MPASM.
  8. - 14th March 2006, 02:59 #8
    mister_e's Avatar
    mister_e
    mister_e is offline Contributor
    Join Date
    Sep 2004
    Location
    montreal, canada
    Posts
    6,898

    Did you find this post helpful? Yes | No

    Default

    Hi Tech C is certainely good. I have it but use but used it rarely... worst now

    The only thing is just that it's a bit expensive.

    To be honnest, i used some DSPic in the past and convert the same stuff to 18F... no big difference... just harder to figure out how to.

    Be really sure that you need a DSPic before spending your cash on it. 18F are really capable... if you mind to give your brain a few hour/week/month intensive thinking.
    Steve

    It's not a bug, it's a random feature.
    There's no problem, only learning opportunities.
  9. - 14th March 2006, 04:00 #9
    Normnet's Avatar
    Normnet
    Normnet is offline Contributor
    Join Date
    Oct 2004
    Posts
    440

    Did you find this post helpful? Yes | No

    Default

    Rip-off?

    CircuitED:
    Easy dsPic3 board includes GLCD,LCD, & DS1820 $174.00
    Compiler when purchased with above $99.00
    Shipping FREE USA, USA distributor.
    Total Circuit Ed $273.00

    Mikroelektronika:
    Easy dsPic3 board $119.00
    Compiler when purchased with above $99.00
    GLCD $17.00
    LCD & DS1820 $15.00
    Shipping worldwide $25.00
    (Yugoslavia shipping could take weeks)
    Total Mikroelektronika $275.00

    Norm
  10. - 3rd May 2006, 23:24 #10
    fanie's Avatar
    fanie Guest

    Did you find this post helpful? Yes | No

    Default

    Mister-e

    >>To be honnest, i used some DSPic in the past and convert the same stuff to 18F... no big difference... just harder to figure out how to

    The real difference would of course be the peripherals and the 40 mips you'd have to overcome with an 18 series. I bet Norm here would agree with this...
  11. - 4th May 2006, 03:13 #11
    mister_e's Avatar
    mister_e
    mister_e is offline Contributor
    Join Date
    Sep 2004
    Location
    montreal, canada
    Posts
    6,898

    Did you find this post helpful? Yes | No

    Talking

    Fanie,
    Just a little example... how many times we saw, see and we will see in the future, people using 20 mhz or higher speed crystal for simple task where 4MHZ is often too much or just enough? How many time we see here some task that should be done without any PIC...

    Same for DsPIC i guess. Yeah they're great, Fast, quite reliable about the pricing, and have tons of ring and bells (a few much than 18F). But thinking never killed anybody on this earth when capable of. Few cents, dollars much on a single parts when you build few thousand/millions units... Same for extra i/o, pcb design ... you know.

    So unless i really need for extreme speed for a really specific task, i'll use them... but they're also young on the market for now. I just leave other having problems with before

    Oh, how about future DsPIC support in your other compiler?

    LMAO!!!!
    Last edited by mister_e; - 4th May 2006 at 03:19.
    Steve

    It's not a bug, it's a random feature.
    There's no problem, only learning opportunities.
  12. - 5th May 2006, 00:09 #12
    fanie's Avatar
    fanie Guest

    Did you find this post helpful? Yes | No

    Default

    Hallo Steve,

    >>Oh, how about future DsPIC support in your other compiler?

    Seems it's going to be a while still - keep in mind it's not even supported by the C's yet...
  13. - 5th May 2006, 02:23 #13
    mister_e's Avatar
    mister_e
    mister_e is offline Contributor
    Join Date
    Sep 2004
    Location
    montreal, canada
    Posts
    6,898

    Did you find this post helpful? Yes | No

    Default

    It seems you need an update. Yeah it's support by some C compiler. If it wasn't i'd never ever waste my time in assembler... I used Hi-Tech C in the past.

    http://www.htsoft.com/products/dspicccompiler.php

    http://www.iar.com/index.php?show=98...7/p987_eng.php

    http://www.microchip.com/stellent/id...&part=SW006012

    I think some other crap one support them but i'll never say their name. Oh OK, just the the first 3 letter MIK.
    Steve

    It's not a bug, it's a random feature.
    There's no problem, only learning opportunities.
  14. - 5th May 2006, 05:00 #14
    GeoJoe's Avatar
    GeoJoe
    GeoJoe is offline Junior Member
    Join Date
    Feb 2006
    Location
    Arvada Colorado
    Posts
    31

    Did you find this post helpful? Yes | No

    Default Dsp

    I mangaged to get my project running with assembler. It took a lot of effort and time. In fact, I hated it.
    I guess what I want from a development platform is the security of knowing that I have invested time and money into something that will carry me into the future. Microcontroller technology will continue to grow. I'd like to not learn a new system every time a new controller comes out. I'd rather concentrate on implementing the advanced features of the micro. That's better than de-bugging new code. Does anyone think that new micro's get a bad rap for some time when they come out (Silicon bugs aside) because people don't know how to use them?
  15. - 5th May 2006, 15:47 #15
    mister_e's Avatar
    mister_e
    mister_e is offline Contributor
    Join Date
    Sep 2004
    Location
    montreal, canada
    Posts
    6,898

    Did you find this post helpful? Yes | No

    Default

    The Microchip C compiler may be free but give real limitation and i'm not a fan of that one... as some here.

    In fact, if someone should learn only one language that cover every PIC in the whole Microchip familly and have all the cash to spend on a compiler for support and upgrade, Hi-Tech C PICC Enterprise Edition would be the smart choice. BUT as most here use 12F, 16F,18F and sometime 10F... i bet Melabs PicBasic, or some other, is more than enough.

    Assembler is free, but a real pain to code with. Well at least i can't imagine to do some 32K or more ONLY in assembler
    Steve

    It's not a bug, it's a random feature.
    There's no problem, only learning opportunities.
« Previous Thread | Next Thread »

Similar Threads

  1. PBP PIC32 series support?
    By foss in forum mel PIC BASIC Pro
    Replies: 2
    Last Post: - 18th August 2008, 12:10
  2. Melabs PIC Basic Pro - 16 bit devices support
    By rod27cn in forum PBP Wish List
    Replies: 10
    Last Post: - 21st November 2007, 08:21
  3. PicBasic Pro CAN Support?
    By RMUTR in forum mel PIC BASIC Pro
    Replies: 3
    Last Post: - 18th November 2006, 00:19
  4. support for pic18f4520
    By vaidyasp1 in forum mel PIC BASIC Pro
    Replies: 4
    Last Post: - 28th April 2006, 13:05
  5. cell phone support text mode
    By microkam in forum mel PIC BASIC Pro
    Replies: 1
    Last Post: - 23rd July 2005, 10:05

Members who have read this thread : 0

You do not have permission to view the list of names.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules