Here's the schematic that goes with the code:
|
Here's the schematic that goes with the code:
My Creality Ender 3 S1 Plus is a giant paperweight that can't even be used as a boat anchor, cause I'd be fined for polluting our waterways with electronic devices.
Not as dumb as yesterday, but stupider than tomorrow!
|
Hi Robert,
That's going to be hard. The program is written for an 8051 type processor.
Many of the 8051 directives are similar to the PIC ones, but you'll have to re-write the whole program.
.
DT
|
By the tone of your reply, I take it that it's more than just correcting the command syntax and that the actual coding is affected as well...
Darn, this was the best example I had to manage an Optrex 51553 gLCD. I've scoured Google and found nothing for the SED1565 controller. I've checked out the links posted in here fo gLCDs, but they are all for other types of controllers.
That really sucks 'cause this LCD is really cool; white font over a blue backgound, with backlighting and touch screen. That, and the fact I have 5 on hand and just finally managed to assemble a PCB to receive the 0.5mm pitch flexible film connector.
Robert
My Creality Ender 3 S1 Plus is a giant paperweight that can't even be used as a boat anchor, cause I'd be fined for polluting our waterways with electronic devices.
Not as dumb as yesterday, but stupider than tomorrow!
|
Ok, I'll give it a try.
Darrel, you wouldn't happen to have a link to 8051 syntax? That would cut down on some research time and I'd be certain of looking at the proper code. I'd hate to convert all this wrong.
Should I convert to MPASM or PM? PM is supposed to be faster, but I don't know if it supports all the commands.
Robert
My Creality Ender 3 S1 Plus is a giant paperweight that can't even be used as a boat anchor, cause I'd be fined for polluting our waterways with electronic devices.
Not as dumb as yesterday, but stupider than tomorrow!
|
I've found a nice reference for 8051 here:
http://www.ece.umr.edu/computing/uni...e/tasking/asm/
Now I just have to figure if I need PM or MPASM...
Robert
My Creality Ender 3 S1 Plus is a giant paperweight that can't even be used as a boat anchor, cause I'd be fined for polluting our waterways with electronic devices.
Not as dumb as yesterday, but stupider than tomorrow!
|
This is reassuring:
"PM includes an 8051-style instruction set that is more intuitive than the Microchip mnemonics. For complete information on the PICmicro Macro Assembler, see the PM.TXT file on disk."
Crossing my fingers in hopes that I have enough information to convert this.
Robert
My Creality Ender 3 S1 Plus is a giant paperweight that can't even be used as a boat anchor, cause I'd be fined for polluting our waterways with electronic devices.
Not as dumb as yesterday, but stupider than tomorrow!
|
Hi!
Using a Graphics-Based LCD Module
http://www.circuitcellar.com//librar...c0400cdpdf.pdf
Interfacing to a Hantronix 128 × 64 Chip-On-Glass LCD
(Basic Stamp code - SED1565 controller)
http://www.hantronix.com/down/a12864cog.pdf
Also using the SED1565 controller:
http://sandiding.tripod.com/n7110.html
http://sandiding.tripod.com/nokialcd7110.html
Merry Christmas!
Luciano
Last edited by Luciano; - 24th December 2005 at 09:28.
Members who have read this thread : 0You do not have permission to view the list of names.
Posting Permissions
Bookmarks