having problems with Hantronix 20x4 lcd

[MikeTamu]

How about you post your code?

[Luciano]

Hi,

I was talking about your problem with the LCD.

Yesterday, before posting, I went through your previous threads
and I saw amongst other threads "problem with LCD" and "xtal problem".

The timing is important for a HD44780-based LCD, especially during its initialization.

The purpose of my test was to check the oscillator frequency. (SW & HW).
After all, your post was saying "I can not get anything out of it".

Post your code.

Best regards,

Luciano

[Rhatidbwoy]

luciano.
thanks for the concern for everything that i have posted on this forum. I got many things to work since I started to write to this forum. xtal problem i fixed with INTRC. The first lcd problem I got to work with the contrast setting. The seond lcd is a hantronix and that is were I am having problems.

The hantronix screen that I have is the hdm-20416h. The contrast should be controlled with either a single or dual power source. I tried the single and that did not work. I am now working with a dual power source for the contrast and that works. It is not much that it needs dual power source but that it need to have more than 5volt to work. The second problem that I have with the hantronix screen is that the line address is not correct. Line 1 starts with $00 but to go any further into the line i can not do. Line 2 threw 4 is not to what the hantronix reccomend, but it is $C0, $94, $D4 . Those are the line addresses that I have figured out and what I have gotten to work so far. I am having a time trying to figure out what is happenning with line 1, but that is nothing more than the other problems that I had. Time will tell in getting it to work.

Thank you again for suggestion that I could use for figuring out timing issues.

The code that I am using is as follows:

' PicBasic program to demonstrate operation of an LCD in 4-bit mode
' PIC16F628
' LCD should be connected as follows:
' LCD PIC
' DB4 PortA.0
' DB5 PortA.1
' DB6 PortA.2
' DB7 PortA.3
' RS PortA.4 (add 4.7K pullup resistor to 5 volts)
' E PortB.3
' RW Ground
' Vdd 5 volts
' Vss Ground
' Vo 20K potentiometer (or ground)
' DB0-3 No connect

Pause 1000 ' Wait for LCD to startup
CMCON = 7

loop: Lcdout $fe, 1 ' Clear LCD screen

lcdout $FE, $00 + 0, "LINE 1"
lcdout $FE, $C0 + 0, "LINE 2"
lcdout $FE, $94 + 0, "LINE 3"
lcdout $FE, $D4 + 0, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
lcdout $FE, $00 + 1, "LINE 1"
lcdout $FE, $C0 + 1, "LINE 2"
lcdout $FE, $94 + 1, "LINE 3"
lcdout $FE, $D4 + 1, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
lcdout $FE, $00 + 2, "LINE 1"
lcdout $FE, $C0 + 2, "LINE 2"
lcdout $FE, $94 + 2, "LINE 3"
lcdout $FE, $D4 + 2, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
lcdout $FE, $00 + 3, "LINE 1"
lcdout $FE, $C0 + 3, "LINE 2"
lcdout $FE, $94 + 3, "LINE 3"
lcdout $FE, $D4 + 3, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
lcdout $FE, $00 + 4, "LINE 1"
lcdout $FE, $C0 + 4, "LINE 2"
lcdout $FE, $94 + 4, "LINE 3"
lcdout $FE, $D4 + 4, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 5, "LINE 1"
lcdout $FE, $C0 + 5, "LINE 2"
lcdout $FE, $94 + 5, "LINE 3"
lcdout $FE, $D4 + 5, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 6, "LINE 1"
lcdout $FE, $C0 + 6, "LINE 2"
lcdout $FE, $94 + 6, "LINE 3"
lcdout $FE, $D4 + 6, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 7, "LINE 1"
lcdout $FE, $C0 + 7, "LINE 2"
lcdout $FE, $94 + 7, "LINE 3"
lcdout $FE, $D4 + 7, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 8, "LINE 1"
lcdout $FE, $C0 + 8, "LINE 2"
lcdout $FE, $94 + 8, "LINE 3"
lcdout $FE, $D4 + 8, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 9, "LINE 1"
lcdout $FE, $C0 + 9, "LINE 2"
lcdout $FE, $94 + 9, "LINE 3"
lcdout $FE, $D4 + 9, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 10, "LINE 1"
lcdout $FE, $C0 + 10, "LINE 2"
lcdout $FE, $94 + 10, "LINE 3"
lcdout $FE, $D4 + 10, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 11, "LINE 1"
lcdout $FE, $C0 + 11, "LINE 2"
lcdout $FE, $94 + 11, "LINE 3"
lcdout $FE, $D4 + 11, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 12, "LINE 1"
lcdout $FE, $C0 + 12, "LINE 2"
lcdout $FE, $94 + 12, "LINE 3"
lcdout $FE, $D4 + 12, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 13, "LINE 1"
lcdout $FE, $C0 + 13, "LINE 2"
lcdout $FE, $94 + 13, "LINE 3"
lcdout $FE, $D4 + 13, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 14, "LINE 1"
lcdout $FE, $C0 + 14, "LINE 2"
lcdout $FE, $94 + 14, "LINE 3"
lcdout $FE, $D4 + 14, "LINE 4"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 15, "LINE "
lcdout $FE, $C0 + 15, "LINE "
lcdout $FE, $94 + 15, "LINE "
lcdout $FE, $D4 + 15, "LINE "

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 16, "LINE"
lcdout $FE, $C0 + 16, "LINE"
lcdout $FE, $94 + 16, "LINE"
lcdout $FE, $D4 + 16, "LINE"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 17, "LIN"
lcdout $FE, $C0 + 17, "LIN"
lcdout $FE, $94 + 17, "LIN"
lcdout $FE, $D4 + 17, "LIN"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 18, "LI"
lcdout $FE, $C0 + 18, "LI"
lcdout $FE, $94 + 18, "LI"
lcdout $FE, $D4 + 18, "LI"

pause 2000
Lcdout $fe, 1 ' Clear LCD screen
'lcdout $FE, $00 + 19, "L"
lcdout $FE, $C0 + 19, "L"
lcdout $FE, $94 + 19, "L"
lcdout $FE, $D4 + 19, "L"
PAUSE 250

GOTO LOOP

[Luciano]

Hi,

Add 80h to the character address (set bit 7) to make
the Display Data RAM Address Set command.

$80 -> 1st line
$c0 -> 2nd line
$94 -> 3rd line
$d4 -> 4th line

Best regards,

Luciano

[Rhatidbwoy]

the thing about $80 for the first line is that it does not even register on the screen. I have it at 00 right now and that is the only thing that has anything registered on the screen

$80 does nothing. The funny part to me is that the spec sheet for this screen says that:

line1 $00
line2 $40
line3 $14
line4 $54

nothing is even close

[Luciano]

$00 + $80 = $80
$40 + $80 = $c0
$14 + $80 = $94
$54 + $80 = $d4

Luciano

[Rhatidbwoy]

tell me if this is not funny.

For the hantronix hdm-20416h row1 column1 is $00. Row1 column2 is $80. Then anything to follow row1 column2 is $80 + what ever column that I want it to fall under. I found this out at 5:47pm central time on 18 dec 05. took me one week to figure out all my problems.

[Luciano]

Hi

When you power-up the LCD, its cursor position is on line 1 position 1.
The LCD does that automatically. Also when you clear the LCD the
cursor will go back to line 1 position 1.

So if just after LCD power-up or after a LCD clear you write the PicBasic code ....

Lcdout "test"

... the word "test" will be displayed one line 1 and will use the first 4 locations on line 1.

* * *

To input instructions to the LCD module, such as clear screen, go to line 2, etc., you
must prefix the instruction with 254 (0xFE). The byte following prefix is seen and
treated as a instruction code. After the instruction code, the LCD automatically returns
to text mode. Every instruction code must be sent with its own 254 prefix (0xFE).

Cursor position on a four lines LCD:

To move the cursor to the beginning of the first line and display a text you will need
to send the prefix $FE, the instruction code $80 and the text to be displayed.

Example:
LCDOUT $FE,$80, "Hello on line 1"

To move the cursor to the beginning of the second line and display a text you will need
to send the prefix $FE, the instruction code $C0 and the text to be displayed.

Example:
LCDOUT $FE,$C0, "Hello on line 2"

To move the cursor to the beginning of the third line and display a text you will need
to send the prefix $FE, the instruction code $94 and the text to be displayed.

Example:
LCDOUT $FE,$94, "Hello on line 3"

To move the cursor to the beginning of the fourth line and display a text you will need
to send the prefix $FE, the instruction code $D4 and the text to be displayed.

Example:
LCDOUT $FE,$D4, "Hello on line 4"

* * *


In your program, just after LCD power-up or just after a display clear you send:

lcdout $FE, $00 + 0, "LINE 1"

With the above code you just send a NOP instruction ($0) to the LCD controller.
(NOP = Short for No OPeration). The LCD controller ignores your NOP instruction and
will stay on line 1 position 1 and the output text "LINE 1" will go
on line 1 position 1 because you don't have changed the LCD cursor position.

Try to write a text on line 2 and then, without clearing line 2, go to line 1 and write a text on line 1.
If you tray that you will understand the purpose of the PicBasic code
LCDOUT $FE,$80, "Hello on line 1".

Best regards,

Luciano