I did explain the theory and operation on this thread...
http://www.picbasic.co.uk/forum/showthread.php?t=1761
Schematic appended.
|
I did explain the theory and operation on this thread...
http://www.picbasic.co.uk/forum/showthread.php?t=1761
Schematic appended.
|
Hi Melanie,Originally Posted by Melanie
I just took a look at the thread you referenced and got a strange feeling of Deja Vu.
Reading the start of the thread I got the feeling I had read it before, then I realised.
Both threads were started by the same person asking exactly the same question (apart from one extra sentence)!
Aside from that, can I ask how you remember what you have typed before and in what thread. I know you are a dab hand with the search function but remembering which of your post is which is a pretty impressive feat!
Keith
www.diyha.co.uk
www.kat5.tv
|
Ah... in this case it was easy...
MegaAdy earlier today asked me for a schematic off-list reminding me of that thread... as I was about to reply I noticed he had posted the question again on-list as well, so I posted the schematic publicly. So no great feat of mental prowess in this instance... and all this from a girl who mislays her car keys a dozen times a week!
|
Just looking at that schematic, it may be necicary to note that you will get a voltage drop accross the R1 resistor as well as a voltage drop across the diode. You would want to make sure the voltage getting to the slave pic is sufficient.
As for the large capacitor, you can get 5v, 0.047F (or 47000uF) caps. They are small, quite cheap, and will maintain power for your PIC for a number of seconds.
Last edited by Kamikaze47; - 23rd November 2005 at 20:59.
|
Don't worry Melanie, we can fix your car keys problem...
|
Surgically implanted obviously! Great idea. Now all I got to do is get all the locks in my life changed to be chip proximity activated.
Kamikaze...
The Voltage drop across R1 will be negligible once C1 has charged since the micropower PICs draw only a few uA. However I do have issue with Caps that size... they'll take forever to charge and the voltage rise-time at the Slave end will be so slow that the PIC will not initialise for the best part of a minute! Just work out the CR time constant!
|
You disappoint me Melanie
After all those superb code examples, I thought you had some magical formula for finding previously written information
Good to know you suffer from the same problems as the rest of us.
I have lost count of the number of times I have put down a screwdriver and two minutes later when I go to pick it up it isnt there!
Nice solution to the problem BTW. My initial thoughts were for a choke at each end and use a carrier to modulate a tone onto the power rail. Much higher component count and cost.
Regards
Keith
www.diyha.co.uk
www.kat5.tv
|
Thank you for schematic Melanie ! You were right, I posted this question some months ago. You didn't understand my setup here. So, once again,
I have two devices ( not pics ). A master device, and a slave device that get power from the slave (5v, 3-400 mA ). Now, I want to put a PIC in the slave device which should send to the pic I put in the master device a few bytes ( 1200 baud ). The problem is the power consumption of the slave ( 4-500mA). And I can not use too big caps like ... 4700u@25v. I can not test the schematic right now, but I got the ideea. But do you thing it will work in the context I explained you ? The power on that slave device ( and the transmitting pic also ) should be kept as close as it can to 5V. Thank you .
|
If your Slave device is power hungry, then the only way is to modulate a signal onto the Power Supply lines as suggested by Keith. The schematic I've posted would not be appropriate in that instance.
|
hm ... can you please be more specific ?
Members who have read this thread : 0You do not have permission to view the list of names.
Posting Permissions
Bookmarks