PIC18F45K22 Not working

[Ioannis]

Simple LED test but no joy. Cannot see why it is not working.

On PortB(0-3) there are 4 LEDs connected to ground and LED1 and LED2 are faint ON, rest OFF.

#CONFIG
    CONFIG  FOSC = INTIO67        ; Internal oscillator block
    CONFIG  PLLCFG = ON           ; PLL Control
    CONFIG  PRICLKEN = OFF        ; Primary clock can be disabled by software
    CONFIG  FCMEN = OFF           ; Fail-Safe Clock Monitor disabled
    CONFIG  IESO = OFF            ; Oscillator Switchover mode disabled
    CONFIG  PWRTEN = OFF          ; Power up timer disabled
    CONFIG  BOREN = SBORDIS       ; Brown-out Reset enabled in hardware only (SBOREN is disabled)
    CONFIG  BORV = 190            ; VBOR set to 1.90 V nominal
    CONFIG  WDTEN = OFF            ; WDT is always enabled. SWDTEN bit has no effect
    CONFIG  WDTPS = 32768         ; 1:32768
    CONFIG  CCP2MX = PORTC1       ; CCP2 input/output is multiplexed with RC1
    CONFIG  PBADEN = OFF          ; PORTB<5:0> pins are configured as digital I/O on Reset
    CONFIG  CCP3MX = PORTB5       ; P3A/CCP3 input/output is multiplexed with RB5
    CONFIG  HFOFST = ON           ; HFINTOSC output and ready status are not delayed by the oscillator stable status
    CONFIG  T3CMX = PORTC0        ; T3CKI is on RC0
    CONFIG  P2BMX = PORTD2        ; P2B is on RD2
    CONFIG  MCLRE = INTMCLR       ; MCLR pin disabled, RE3 input pin enabled
    CONFIG  STVREN = ON           ; Stack full/underflow will cause Reset
    CONFIG  LVP = OFF             ; Single-Supply ICSP disabled
    CONFIG  XINST = OFF           ; Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
    CONFIG  DEBUG = OFF           ; Disabled
    CONFIG  CP0 = OFF             ; Block 0 (000800-001FFFh) not code-protected
    CONFIG  CP1 = OFF             ; Block 1 (002000-003FFFh) not code-protected
    CONFIG  CP2 = OFF             ; Block 2 (004000-005FFFh) not code-protected
    CONFIG  CP3 = OFF             ; Block 3 (006000-007FFFh) not code-protected
    CONFIG  CPB = OFF             ; Boot block (000000-0007FFh) not code-protected
    CONFIG  CPD = OFF             ; Data EEPROM not code-protected
    CONFIG  WRT0 = OFF            ; Block 0 (000800-001FFFh) not write-protected
    CONFIG  WRT1 = OFF            ; Block 1 (002000-003FFFh) not write-protected
    CONFIG  WRT2 = OFF            ; Block 2 (004000-005FFFh) not write-protected
    CONFIG  WRT3 = OFF            ; Block 3 (006000-007FFFh) not write-protected
    CONFIG  WRTC = OFF            ; Configuration registers (300000-3000FFh) not write-protected
    CONFIG  WRTB = OFF            ; Boot Block (000000-0007FFh) not write-protected
    CONFIG  WRTD = OFF            ; Data EEPROM not write-protected
    CONFIG  EBTR0 = OFF           ; Block 0 (000800-001FFFh) not protected from table reads executed in other blocks
    CONFIG  EBTR1 = OFF           ; Block 1 (002000-003FFFh) not protected from table reads executed in other blocks
    CONFIG  EBTR2 = OFF           ; Block 2 (004000-005FFFh) not protected from table reads executed in other blocks
    CONFIG  EBTR3 = OFF           ; Block 3 (006000-007FFFh) not protected from table reads executed in other blocks
    CONFIG  EBTRB = OFF           ; Boot Block (000000-0007FFh) not protected from table reads executed in other blocks
#ENDCONFIG
                         
' Setup PLL for 64 MHZ
OSCCON = %01110000 ; 16 mhz (NOTE: SCS=0 so PLL works)
OSCCON2 = %00000100
OSCTUNE = %01000000 ; PLL enable Mhz * 4 

DEFINE OSC 64

ANSELA = 0
ANSELB = 0
ANSELC = 0
ANSELD = 0
ANSELE = 0

WPUB= 255
 
'Initializing Registers
  porta=0:portb = 255:portc=0:portd=0:porte=0
  trisa = 0
  trisb.5=%00100000
  portc.6=1
  trisc.6=0
  trisd = 0
  trise = 0  

'Variable set
but     var portb.5

latb=0
while 1
latb.0=1:pause 100:latb.0=0:pause 100
wend

end

Ioannis

[Ioannis]

Do not bother... Found the embarrasing stupid mistake that blew the Port B all together!

Marked with bold red on the code above.

Ioannis

[Demon]

That was enough to damage the port?

[Ioannis]

I don't think this is something dangerous. It just did not setup the port properly and of course did not work as an output.

No damage at all.

Still very stupid mistake, not easy to see.

Ioannis