Replacing 16F628A with 16F1827 - need help, please !

[fratello]

Hi all !
I have a montage where I use 16F628A I/P with the settings below. Due to the price that has increased a lot and the unavailability (is it an older generation?) I would like to switch to 16F1827 (or 16F1826), which has the same number and arrangement of ports. I don't use ADC at all !
Can somebody help me with some advice, what exactly should I change in the uC setting part? I looked in the datasheet, but it is (much too) complex for my level...
Thank you in advance for any answer !

On port A 2,3,4 I read if level is high or low, on port B (all) I run 0 or 1 logic according to levels on port A. That's all !

@ __config _INTOSC_OSC_NOCLKOUT & _WDT_OFF & _PWRTE_ON & _MCLRE_ON & _BODEN_ON & _LVP_OFF & _CP_OFF

include "alldigital.pbp"
   DEFINE   OSC 4           ' 4MHz 
   CMCON = 7                ' Disable on-chip comparator, PORTA in digital mode


TRISA = %00011100           
PORTA = %00011100
PORTB = %00000000
TRISB = %11111111

OPTION_REG.7 = 1

[Ioannis]

Here are my settings. Use it as a starting point.

#config
  __config _CONFIG1, _FOSC_INTOSC & _WDTE_ON & _PWRTE_ON & _MCLRE_OFF & _CP_OFF & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_OFF & _FCMEN_OFF
  __config _CONFIG2, _WRT_OFF & _PLLEN_OFF & _LVP_OFF & _STVREN_OFF ;& _BORV_25
#endconfig

DEFINe OSC 32

DEFINE HSER_RCSTA 90h
DEFINE HSER_TXSTA 24h				'9600 baud rate, BRGH=1
DEFINE HSER_BAUD 115200
DEFINE HSER_SPBRG 68
DEFINE HSER_CLROERR 1          

'' Set LCD Data port
'DEFINE LCD_DREG PORTB
'' Set starting Data bit (0 or 4) if 4-bit bus
'DEFINE LCD_DBIT 4
'' Set LCD Register Select port
'DEFINE LCD_RSREG PORTA
'' Set LCD Register Select bit
'DEFINE LCD_RSBIT 6
'' Set LCD Enable port
'DEFINE LCD_EREG PORTA
'' Set LCD Enable bit
'DEFINE LCD_EBIT 7
'' Set LCD bus size (4 or 8 bits)
'DEFINE LCD_BITS 4
'' Set number of lines on LCD
'DEFINE LCD_LINES 2
'' Set command delay time in us
'DEFINE LCD_COMMANDUS 2500
'' Set data delay time in us

DEFINE LCD_DATAUS 50
DEFINE ADC_BITS 10 ' Set number of bits in result (8, 10 or 12)
DEFINE ADC_CLOCK 2 ' Set clock source (FOSC/32=2, RC = 3)
DEFINE ADC_SAMPLEUS 5 ' Channel change pause in μs

OSCCON= %11110000   'PLL enabled, Internal RC-8MHz
 
while !oscstat.6 : wend

'set Pull ups on Port B
WPUB=%11111111

'set pull ups on Port A
WPUA=%00000000

PORTA = 0:PORTB=%00000000
TRISA = %00001111

TRISB = %00000000

ADCON0 = %00000000
ADCON1 = %00000000

ANSELA = %00000000           ' No analog
ANSELB = %00000000           ' RB digital

'APFCON0 = %00000000
'APFCON1 = %00000001

'BAUDCON = %00011000          'Bit 4: 1 Inverted data on Tx, 0 Non inverted

'CCP1CON = %00000000          'Control of CCPx modules
'CCP2CON = %00000000
'CCP3CON = %00000000
'CCP4CON = %00001100

CM1CON0.7=0    'Comparator 1 OFF
CM2CON0.7=0    'Comparator 2 OFF

CPSCON0 = 0    'Cap sense OFF
CPSCON1 = 0    'Cap sense OFF

DACCON0 = 0    'DAC off

FVRCON = 0  'Fixed Voltage reference OFF

OPTION_REG = %01000111  'Tmr0 from 256 presc and Int Clock

;INTEDG set for INTE interrupts
;IOCBP = %00000000           'Disable Positive edge IOC on PortB
;IOCBN = %00000111           'Enable IOC on negative edge
;INTCON = %10001000'%10001000          'Enable global interrupts and IOC

WDTCON = %00010101

INTCON = %00000000      ' Interrupt enable and INTE enable
                       
'PIR1 = 0             ' clear TMR1 int flag                     
'PIE1 = %00000001     ' TMR1 int enabled

'T1CON = %00110000    ' TMR1 1:8 prescale, timer1 off
'  
'DEFINE CCP4_REG PORTA
'DEFINE CCP1_BIT 4    
'DEFINE CCP2_REG PORTB
'DEFINE CCP2_BIT 6

Ioannis

[fratello]

Thank you ! Just tried ... What could cause these two errors?

[DaveP]

It looks like you have a 16F1826 selected instead of 16F1827.

[HenrikOlsson]

Those errors comes from using the wrong syntax for the CONFIG block. The example Ioannis posted compiles just fine.

[fratello]

Yes, the Config block generated errors.
Solved by writing :

ASM
  __config _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_ON & _MCLRE_OFF & _CP_ON & _CPD_ON & _BOREN_OFF & _CLKOUTEN_OFF & _IESO_ON & _FCMEN_ON
  __config _CONFIG2, _WRT_ALL & _PLLEN_ON & _STVREN_ON & _LVP_OFF & _BORV_19 &  _LVP_OFF
ENDASM

Thank you all for your support.
I am going to check if the assembly works correctly.