I want to get two consecutive bytes from one "Hello!" string. How more clear I can say this in other way?


I'll try once again. I need output of this kind from Hello!
A=H
B=e
A=l
B=l
A=o
B=!
easy as

Code:
;----[16F886 Hardware Configuration]--------------------------------------------#CONFIG
cfg1 = _INTRC_OSC_NOCLKOUT    ; INTOSCIO oscillator: I/O function on RA6/OSC2/CLKOUT pin, I/O function on RA7/OSC1/CLKIN
cfg1&= _WDT_ON                ; WDT enabled
cfg1&= _PWRTE_OFF             ; PWRT disabled
cfg1&= _MCLRE_OFF             ; RE3/MCLR pin function is digital input, MCLR internally tied to VDD
cfg1&= _CP_OFF                ; Program memory code protection is disabled
cfg1&= _CPD_OFF               ; Data memory code protection is disabled
cfg1&= _BOR_OFF               ; BOR disabled
cfg1&= _IESO_ON               ; Internal/External Switchover mode is enabled
cfg1&= _FCMEN_ON              ; Fail-Safe Clock Monitor is enabled
cfg1&= _LVP_OFF               ; RB3 pin has digital I/O, HV on MCLR must be used for programming
cfg1&= _DEBUG_OFF             ; In-Circuit Debugger disabled, RB6/ICSPCLK and RB7/ICSPDAT are general purpose I/O pins
  __CONFIG _CONFIG1, cfg1




cfg2 = _BOR40V                ; Brown-out Reset set to 4.0V
cfg2&= _WRT_OFF               ; Write protection off
  __CONFIG _CONFIG2, cfg2




#ENDCONFIG




'chip configs
TRISA=%00000000  'SET A TO OUTPUT   1=input
TRISC=%00001101   'set half C for in/out
TRISB=%00011000   'set PortB to output
ANSELH=%00000000   ' ADC OFF B
ANSEL=%000000000 'configure PortA as digital except first 2
ADCON1=%10000000  'adc justify
OSCCON=%01110101  'SET FREQUENCY TO 8MHZ
WPUB=%00000000    'turn off Pullups
CM1CON0=0         'DISABLE COMPARATORS
CM2CON0=0         'SAME HERE
'CCP1CON=%01000000 ' configure pwm
'PSTRCON=%00010110 'disable C pwm




DEFINE OSC 8   
DEFINE ADC_BITS 10
DEFINE ADC_CLOCK 3
DEFINE ADC_SAMPLEUS 50
'lcd config
pause 1000 
' Set LCD Data port 
DEFINE LCD_DREG PORTC  
DEFINE LCD_DBIT 4  
DEFINE LCD_RSREG PORTB  
DEFINE LCD_RSBIT 0  
DEFINE LCD_EREG PORTB  
DEFINE LCD_EBIT 1  
DEFINE LCD_BITS 4  
DEFINE LCD_LINES 2  
DEFINE LCD_COMMANDUS 2000  
DEFINE LCD_DATAUS 44
lcdout $fe, $1,  "ready "
pause 1000


DPIN Var PORTA.2       ' I2C data pin
CPIN Var PORTA.1       ' I2C clock pin
B   Var word
B0   Var byte
B1   Var byte
lcdwbuf var word[10]
@lcdBuf = _lcdwbuf
lcdBuf    Var byte ext






 arraywrite lcdBuf ,["Hello World",0 ]
 
 lcdout $fe, $1,  str  lcdBuf
 
 b0 = lcdwbuf[0]
 b1 = lcdwbuf[0] >> 8
  lcdout $fe, $c0,b0," : ", b1
  b0= lcdwbuf[3]
 b1= lcdwbuf[3]  >> 8
 pause 1000
   lcdout $fe, $c0,b0," : ", b1