Remote Control I/R TSOP4138 Help


Closed Thread
Results 1 to 4 of 4
  1. #1
    Join Date
    May 2012
    Location
    Merseyside, UK
    Posts
    237

    Default Remote Control I/R TSOP4138 Help

    Hi thank you for reading.

    I have the circuit as below....All software is working fine.

    However I am aware the IP Pin on my Processor (16F627A) is being spiked by mains EMI and causing issues. I know this and I can repeat it by jigging a light switch (Fridge and Oven Stat also do same). The circuit is battery powered by a 12v alarm battery then a LDO 5v Regulator. So no physical connection with mains.

    The 5v supply has decouplers on in and out as per data sheet.... Also there is a 100nf cap in the socket of the 16f627A.


    Any help in stopping my circuit getting spiked welcome.

    See attached AndyCad sketch for circuit.

    AndyName:  IMG_20200320_133855.jpg
Views: 1058
Size:  169.9 KBName:  IMG_20200320_133855.jpg
Views: 1058
Size:  169.9 KB

  2. #2
    Join Date
    Mar 2003
    Location
    Commerce Michigan USA
    Posts
    1,166


    Did you find this post helpful? Yes | No

    Default Re: Remote Control I/R TSOP4138 Help

    Andy, I would place a 10uF ceramic cap across the processor after the 100 Ohm resistor. I would also replace the 100 Ohm with a 10 Ohm. I have to ask what are you doing with the remaining pins on the processor? Also, what other circuits are you powering from the LDO? I am assuming the regulator is somewhere on the left of the schematic?
    Last edited by Dave; - 20th March 2020 at 15:42.
    Dave Purola,
    N8NTA
    EN82fn

  3. #3
    Join Date
    May 2012
    Location
    Merseyside, UK
    Posts
    237


    Did you find this post helpful? Yes | No

    Default Re: Remote Control I/R TSOP4138 Help

    A Little bit more :-

    The unused pins are set as outputs Using TRISA=00000000 and TRISB=00010000 (RB3 is the i/p for the InfraRed)

    Only other cct is a clock DS1307 on RB1 and RB2 (SDA and SCL)

    LDO is LM2931

    Andy

  4. #4
    Join Date
    Mar 2003
    Location
    Commerce Michigan USA
    Posts
    1,166


    Did you find this post helpful? Yes | No

    Default Re: Remote Control I/R TSOP4138 Help

    Andy, What do you mean by " is being spiked by mains EMI and causing issues."? Please explain... What is it doing wrong?
    Dave Purola,
    N8NTA
    EN82fn

Similar Threads

  1. Remote control help
    By paulthegulll in forum mel PIC BASIC Pro
    Replies: 1
    Last Post: - 2nd November 2010, 10:01
  2. Help with remote control
    By Clodoaldo in forum mel PIC BASIC Pro
    Replies: 3
    Last Post: - 8th July 2009, 00:24
  3. IR/RF Remote Control
    By jhorsburgh in forum General
    Replies: 2
    Last Post: - 6th February 2008, 03:23
  4. RF Remote control
    By eralp in forum General
    Replies: 3
    Last Post: - 11th January 2007, 00:15
  5. Remote control
    By Radiance in forum General
    Replies: 2
    Last Post: - 6th August 2003, 16:13

Members who have read this thread : 0

You do not have permission to view the list of names.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts