this works for me

Code:
#CONFIG
  CONFIG  FOSC = INTIO67
  CONFIG  PLLCFG = OFF
  CONFIG  PRICLKEN = OFF
  CONFIG  FCMEN = OFF
  CONFIG  IESO = OFF
  CONFIG  PWRTEN = OFF
  CONFIG  BOREN = SBORDIS
  CONFIG  BORV = 190
  CONFIG  WDTEN = ON
  CONFIG  WDTPS = 32768
  CONFIG  CCP2MX = PORTC1
  CONFIG  PBADEN = OFF
  CONFIG  CCP3MX = PORTB5
  CONFIG  HFOFST = ON
  CONFIG  T3CMX = PORTC0
  CONFIG  P2BMX = PORTB5
  CONFIG  MCLRE = EXTMCLR
  CONFIG  STVREN = ON
  CONFIG  LVP = OFF
  CONFIG  XINST = OFF
  CONFIG  DEBUG = OFF
  CONFIG  CP0 = OFF
  CONFIG  CP1 = OFF
  CONFIG  CP2 = OFF
  CONFIG  CP3 = OFF
  CONFIG  CPB = OFF
  CONFIG  CPD = OFF
  CONFIG  WRT0 = OFF
  CONFIG  WRT1 = OFF
  CONFIG  WRT2 = OFF
  CONFIG  WRT3 = OFF
  CONFIG  WRTC = OFF
  CONFIG  WRTB = OFF
  CONFIG  WRTD = OFF
  CONFIG  EBTR0 = OFF
  CONFIG  EBTR1 = OFF
  CONFIG  EBTR2 = OFF
  CONFIG  EBTR3 = OFF
  CONFIG  EBTRB = OFF
#ENDCONFIG
  
  
        ;INCLUDE "modedefs.bas"
        ;INCLUDE"ALLDIGITAL.pbp"
        ;INCLUDE "HomeAutomationVars.bas"  'Open with PBP editor
        INCLUDE "DT_INTS-18.bas"     ; Base Interrupt System
        INCLUDE "ReEnterPBP-18.bas"     ; Include if using PBP interrupts

    define OSC 8
    
    
    DEFINE DEBUG_REG PORTB  
    DEFINE DEBUG_BIT 7
    DEFINE DEBUG_BAUD 9600 
    ' Set Debug mode: 0 = true, 1 = inverted
    DEFINE DEBUG_MODE 0
    x var word
    rxflag   var bit
    rxchar var byte
ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
 INT_Handler    RX1_INT ,    _read_serial,   PBP,  no
 endm
 INT_CREATE             ; Creates the interrupt processor
ENDASM 
OSCCON = $60   ;  OSC 8
anselc = 0
RCSTA  = $90   ' Enable serial port & continuous receive
TXSTA  = $20   ' Enable transmit, BRGH = 0
SPBRG  = 51    ' 9600 Baud @ 8MHz, 0.16%
SPBRGH = 0
BAUDCON.3 = 1  ' Enable 16 bit baudrate generator
baudcon1= baudcon1&%11001111  ;invert tx/rx polarity   for usb-tty adapter
TRISB.7 = 0  ;DEBUG
LATB.7  = 1  ;DEBUG

   
@   INT_ENABLE   RX1_INT     ; enable external (RX) interrupts    
debug "running",13,10      
Main:
    debug "."    
    for x = 1 to 1000
      if rxflag then
         Debug 13,10,"got !! asc chr ",#rxchar,13,10
         rxflag=0
      endif 
      pauseus 1000
    next x 
     
Goto main   
    
    
read_serial:
    rxflag = 1
    rxchar = rc1reg  
@   INT_RETURN

this is much better , get rid of all those nasty pauses and goto's


Code:
 ;pic18f26k22 rx1 int demo
#CONFIG
  CONFIG  FOSC = INTIO67
  CONFIG  PLLCFG = OFF
  CONFIG  PRICLKEN = OFF
  CONFIG  FCMEN = OFF
  CONFIG  IESO = OFF
  CONFIG  PWRTEN = OFF
  CONFIG  BOREN = SBORDIS
  CONFIG  BORV = 190
  CONFIG  WDTEN = ON
  CONFIG  WDTPS = 32768
  CONFIG  CCP2MX = PORTC1
  CONFIG  PBADEN = OFF
  CONFIG  CCP3MX = PORTB5
  CONFIG  HFOFST = ON
  CONFIG  T3CMX = PORTC0
  CONFIG  P2BMX = PORTB5
  CONFIG  MCLRE = EXTMCLR
  CONFIG  STVREN = ON
  CONFIG  LVP = OFF
  CONFIG  XINST = OFF
  CONFIG  DEBUG = OFF
  CONFIG  CP0 = OFF
  CONFIG  CP1 = OFF
  CONFIG  CP2 = OFF
  CONFIG  CP3 = OFF
  CONFIG  CPB = OFF
  CONFIG  CPD = OFF
  CONFIG  WRT0 = OFF
  CONFIG  WRT1 = OFF
  CONFIG  WRT2 = OFF
  CONFIG  WRT3 = OFF
  CONFIG  WRTC = OFF
  CONFIG  WRTB = OFF
  CONFIG  WRTD = OFF
  CONFIG  EBTR0 = OFF
  CONFIG  EBTR1 = OFF
  CONFIG  EBTR2 = OFF
  CONFIG  EBTR3 = OFF
  CONFIG  EBTRB = OFF
#ENDCONFIG
  
  
INCLUDE "DT_INTS-18.bas"     ; 

define OSC 8
DEFINE DEBUG_REG PORTB  
DEFINE DEBUG_BIT 7
DEFINE DEBUG_BAUD 9600 
DEFINE DEBUG_MODE 0
x         var  byte bank0
flag      var  byte bank0
rxflag    var flag.7
dotflag   var flag.0 
rxchar    var byte
ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
 INT_Handler    RX1_INT  , _read_serial,asm,no
 INT_Handler    TMR1_INT , _TOCK,asm,no
 endm
 INT_CREATE             ; Creates the interrupt processor
ENDASM  
clear  
OSCCON = $60   ;  OSC 8
anselc = 0
RCSTA  = $90   ' Enable serial port & continuous receive
TXSTA  = $20   ' Enable transmit, BRGH = 0
SPBRG  = 51    ' 9600 Baud @ 8MHz, 0.16%
SPBRGH = 0
BAUDCON.3 = 1  ' Enable 16 bit baudrate generator
T1CON=1         ;32mS tick
TRISB.7 = 0  ;DEBUG
LATB.7  = 1  ;DEBUG
baudcon1= baudcon1&%11001111  ;invert tx/rx polarity   for usb-tty adapter
pause 2000    ;give me time to setup debug
@   INT_ENABLE   RX1_INT     ; enable external (RX) interrupts    
debug 13,10 ,"listening "
@ INT_ENABLE  TMR1_INT
x=31
while 1
    if rxflag then
         ;Debug 13,10,"got asc chr ",#rxchar,13,10
         tx1reg = rxchar     ;echo back
         rxflag = 0
    endif 
    if dotflag then
        debug "."                                   
        dotflag=0
    endif 
wend 
end    
read_serial:
ASM
    bsf _flag ,7
    MOVE?BB RC1REG,_rxchar    
    INT_RETURN    
ENDASM
TOCK:
asm
    DECFSZ  _x,F    
    BRA BREXIT
    movlw 31    
    bsf _flag ,0 
    movwf _x         
BREXIT 
    BCF PIR1 ,0 
    INT_RETURN 
ENDASM