A little HELP!!

**aerostar** · - 22nd June 2017, 11:40

Looks likely I can run a partial test on NTSC, I have found the appropriate crystal deep in the odd box, and I have the possible loan of a multi monitor, it is rather old but if it still works it will do NTSC.

I have found the original picbasic files on the web, and that compiles fine for 16F628a. The only thing I have to change are the port numbers to suit my pic/sstv board, all operations will be unchanged.

I do not have a NTSC source, so it would not be a full test, but if text appears, then that should at least prove the NTSC side is working.

It will be a few days before I get the chance to do this.

In the meantime please post if you get your board working on NTSC.

**Ramius** · - 22nd June 2017, 21:48

Hi Aerostar!
I cannot tell how much I appreciate what you are doing! The same as you I have to make some port changes to accommodate wiring. I think I set the TRISB settings correctly and well as the register changes you recommended. This is probably going to sound strange and when I run the code it gets stuck (stops) at "Pause 500"! not sure why?

Code:

 '****************************************************************
'*  Name    : STV-SYNCHS RELEASE                          *
'*  Author  : BOB LEGGETT                                       *
'*  Notice  : Copyright (c) 2009                                *
'*          : All Rights Reserved                               *
'*  Date    : around 2009 or so rehashed now '17         *
'*  Version : 1.0                                               *
'*  Notes   :   VIDEO IDENT                                *
'*          :                                                   *
'****************************************************************

'   WORKS USES SYNC FOR SWITCHING BETWEEN MIXED AND FULL TEXT MODE
'   GOING FROM VID IN TO TEXT AND BACK TO VID IN

INCLUDE "ALLDIGITAL.pbp"
        
define  OSC 20

#CONFIG
    __config _HS_OSC & _WDT_ON & _MCLRE_ON & _LVP_OFF & _CP_OFF
#ENDCONFIG

        
'TV CHIP CONNECTIONS
 
 
'---------------------------------------------------------------

 '16f628a
 
 TVSDA     		VAR PORTB.4    '0     OUTPUT  pin 11 stv was b.1
 CS0     		VAR PORTB.6    '0     OUTPUT pin 13 stv was b.0
 TVSCL     		VAR PORTB.5    '0     OUTPUT  pin 12 stv was b.5
 SYNCH0         VAR PORTB.7    '1     'INPUT    to pin 7 stvchip was b.2
 HEARTBEAT      VAR PORTB.6           'OUTPUT 0  led was b.6
'---------------------------------------------------------------

    ZOOMREG         CON %0000000011001100       ' 12 ZOOM REGISTER
    COLREG          CON %0000000011001101       ' 13 COLOUR REGISTER
    CONREG          CON %0000000011001110       ' 14 CONTROL REGISTER
    POSREG          CON %0000000011001111       ' 15 POSITION REGISTER 
    MODEREG         CON %0000000011010000       ' 16 MODE REGISTER

    
	ICOUNT  		VAR BYTE
	BITCOUNTER 	    VAR BYTE
	WDATA   		VAR WORD
	CHARCOUNTER	    VAR BYTE '  
	LINECOUNTER	    VAR BYTE '

    STVCHAR         VAR BYTE
    ASCCHAR         VAR BYTE
    CHARS           VAR BYTE
    CHARS2          VAR BYTE
    TEMP            VAR BYTE 
    TEMP1           VAR BYTE
    COUNTER         VAR BYTE
    PULSES          VAR BYTE
    CURRENTMODE0    VAR BYTE

'----------------------------------------------------------------     
'    TOPLEFT         CON 0
'    TOPMIDDLE       CON 5
'    TOPRIGHT        CON 10
'    BOTLEFT         CON 2560    '10*256
'    BOTMIDDLE       CON 2565 '(10*256)+ 5
'    BOTRIGHT        CON 2570 '(10*256)+ 10
'---------------------------------------------------------------- 

    DATA @0,"TEST.",$FF,"NO SYNCHS RECEIVED",$FF   



'---------------------------------------------------------------- 
'628
  TRISB=%10000100
'----------------------------------------------------------------     


    PAUSE 500
    
    HIGH HEARTBEAT
    
    
	GOSUB Init
	
    PAUSE 500
	GOSUB Init
    
    CURRENTMODE0=255         ' FORCES TRYSYNCHS TO SET MODE FIRST TIME

	
Demo:

    CHARCOUNTER = 0
	LINECOUNTER = 0
'   CURRENTMODE0 = 0     '0 = MIXED 1 = TEXT
    gosub CLS
    GOSUB TRYSYNCHS      '==================================


    TEMP = 0
  
     

LOOPER:
    GOSUB HEADER    ' LINE 3 RIGHT HAND SIDE TEST.
    IF CURRENTMODE0=1 THEN
    GOSUB NOVIDEO   ' DISPLAYS NO VIDEO IF NO INCOMING SYNCHS
    ENDIF

    
    GOSUB TRYSYNCHS       '===========================
    

    PAUSE 500            'I/2 SECOND DELAY
    TOGGLE HEARTBEAT      ' LED
    GOTO LOOPER          'DO IT FOREVER
  

DISPLAYCHAR:   

    WDATA = %0001011100000000 + STVCHAR
    GOSUB SEND 
    RETURN
SETLINE:    
	WDATA = LINECOUNTER*256 + CHARCOUNTER
    GOSUB Send              'position cursor   
    RETURN



WasteTime:        ' WORKS WITH LESS NOPS



    pauseus 20    ' was 20 nops

	RETURN

StartCommunication:
	TVSCL = 1 'HIGH TVSCL 
    GOSUB WasteTime

    CS0 = 0 'LOW CS0

    GOSUB WasteTime
	TVSCL = 0 'LOW TVSCL
    GOSUB WasteTime
	RETURN

StopCommunication:
	TVSCL = 1 'HIGH TVSCL
    GOSUB WasteTime
    CS0 = 1 'HIGH CS0

    GOSUB WasteTime
	RETURN

SendOne:
	TVSDA = 1 'HIGH TVSDA
    GOSUB WasteTime
	TVSCL = 0 'LOW  TVSCL
    GOSUB WasteTime
	TVSCL = 1 'HIGH TVSCL
    GOSUB WasteTime
	RETURN

SendZero:
	TVSDA = 0 'LOW TVSDA
    GOSUB WasteTime
	TVSCL = 0 ' LOW TVSCL
    GOSUB WasteTime
	TVSCL = 1 'HIGH TVSCL
    GOSUB WasteTime
	TVSDA = 1 'HIGH TVSDA
    GOSUB WasteTime
	RETURN

OutByte:
	FOR   BITCOUNTER = 1 TO 16
    IF    WDATA.15 = 1 THEN
    GOSUB SendOne                       
    ELSE
    GOSUB SendZero
    ENDIF
          WDATA = WDATA << 1
	NEXT  BITCOUNTER
	RETURN

Send:
	GOSUB StartCommunication
	GOSUB OutByte
	GOSUB StopCommunication
	RETURN

'-------------------------------------------------------------  

Init:     '    PAUSE 50 added - seems to improve reliability of init

	TVSCL = 1 'HIGH TVSCL
    TVSDA = 1 'HIGH TVSDA
    CS0   = 1 'HIGH CS0
 
	WDATA = $3000  '%110000 00000000
    GOSUB Send ' Init STV5730
    PAUSE 50
	WDATA = $3000
    GOSUB Send
    PAUSE 50
	WDATA = $00DB  '%00000000 11011011
    GOSUB Send
    PAUSE 50
	WDATA = $1000  '%00010000 00000000
    GOSUB Send
    PAUSE 50
'-------------------------------------------------------------  
	WDATA = %0000000011001100
    GOSUB Send ' Init registers (point to register 12)
    PAUSE 50
'-------------------------------------------------------------      
	WDATA = %0001000000000000   'NORMAL
'   WDATA = %0001000011110000   '4 PIXELS HORIZ AND VERT
    GOSUB Send ' Zoom    ADDRESS 12
    PAUSE 50
'-------------------------------------------------------------      
	WDATA = %0001001000000000

'   WDATA = %0001001000000100
    GOSUB Send ' Color    ADDRESS 13
    PAUSE 50
'--------------------------------------------------------

    WDATA=  %0001101011010100
            'CHANGE BIT 0 TO 1 FOR TEXT ONLY
    GOSUB Send ' Control    ADDRESS 14
'-------------------------------------------------------------    
	WDATA = %0001011111001111
    GOSUB Send ' Position    ADDRESS 15
'------------------------------------------------------------- 

   
	WDATA = %0001000100101110 '$183E BIT 11 CHANGED TO 0  M4 = 0
   
    GOSUB Send ' Mode    ADDRESS 16  %0001100000111110

'------------------------------------------------------------- 
 
	WDATA = $00C0   '%00000000 11000000
    GOSUB Send      ' Set row attributes
     
	FOR ICOUNT = 0 TO 10
    WDATA = $10C4 '%00010000 11000100
                  ' WDATA =%0001000010000111
    GOSUB Send
	NEXT ICOUNT
	RETURN
 
CLS: 
    'character=$0B       'SPACE
     TEMP1=0   ' LINECOUNTER
     TEMP =0    'CHARCOUNTER
loop2:
    
	WDATA = 0  ' LINECOUNTER*256 + CHARCOUNTER   ADDRESS
    GOSUB Send
    

LOOP3:    '                :CHARACTERS        
	WDATA = %0001011100001011  '     1011 0BH SPACECHARACTER
    GOSUB Send
	TEMP = TEMP + 1
	IF TEMP >= 28 THEN
    TEMP = 0
    TEMP1=TEMP1 + 1
	ENDIF
	IF TEMP1 >= 11 THEN SCREENBLANK
 	
    GOTO LOOP3
    
SCREENBLANK:
	RETURN

GETSTVCHAR:                  'CONVERT ASCII TO STV
    STVCHAR =$7F   ' FORCES CLOCK PICTURE IF ERROR         
    LOOKDOWN ASCCHAR,["0123456789- ABCDEFGHIJKLMNOPQRSTUVWXYZ:./'abcdefghijklmnopqrstuvwxyz"],STVCHAR
    RETURN 

HEADER:
    LINECOUNTER=2       'SET START POSITION
    CHARCOUNTER=23      'SET CURSOR POSITION
    GOSUB SETLINE
    FOR CHARS2=0 TO 4
    READ CHARS2, ASCCHAR
    gosub GETSTVCHAR    'CONVERT ASCII TO STV
    GOSUB DISPLAYCHAR
    NEXT
    RETURN
    
NOVIDEO:
    LINECOUNTER=5       'SET START POSITION
    CHARCOUNTER=4       'SET CURSOR POSITION
    GOSUB SETLINE
    FOR CHARS2=6 TO 23      ' FROM EEPROM DATA
    READ CHARS2, ASCCHAR
    gosub GETSTVCHAR    'CONVERT ASCII TO STV
    GOSUB DISPLAYCHAR
    NEXT
    RETURN
    
TRYSYNCHS:
    
    PULSES=0

    COUNT SYNCH0,4,PULSES   '3MS SHOULD COUNT TO 2 OR 3
    IF PULSES > 0 THEN MIXED0
FULL0:

    IF CURRENTMODE0=1 THEN RETURN

    WDATA=  %0000000011001110       'CONTROL REGISTER
    GOSUB SEND
    WDATA=  %0001101011010101 ' was 0001101111010101
   'CHANGE BIT 0 TO 1 FOR TEXT ONLY       OTIGINAL
            
   'WDATA=  %0001101111010100
   'CHANGE BIT 0 TO 1 FOR TEXT ONLY        
    GOSUB SEND

STAYHERE02:
  
    CURRENTMODE0=1
    GOSUB CLS
GOBACK0:
    RETURN


MIXED0:
    IF CURRENTMODE0=0 THEN RETURN
    WDATA=  %0000000011001110       'CONTROL REGISTER
    GOSUB SEND
    WDATA=  %0001101011010101  'was 0001101111010100
    GOSUB SEND

STAYHERE01:

    CURRENTMODE0=0
    GOSUB CLS
    RETURN

I hope I pasted the code correctly this time!!!

Best, Ed

**aerostar** · - 22nd June 2017, 22:51

Have just glanced at your code, first thing I noticed was

You have 2 declarations for Port B.6 this may well be your problem

TVSDA VAR PORTB.4 '0 OUTPUT pin 11 stv was b.1
CS0 VAR PORTB.6 '0 OUTPUT pin 13 stv was b.0 <<<<<<<<<<<<<<<<<<<<<<<<<
TVSCL VAR PORTB.5 '0 OUTPUT pin 12 stv was b.5
SYNCH0 VAR PORTB.7 '1 'INPUT to pin 7 stvchip was b.2
HEARTBEAT VAR PORTB.6 'OUTPUT 0 led was b.6 <<<<<<<<<<<<<<<<<<<<<<<<<<<<

I will have another look tomorrow as it is bedtime over here (UK) and I am tired.

Thought.... as you are only using digital ports PORT B you do not need the include file.
The file just makes all Analog ports digital - it works fine on 628a and others BUT may not work on newer chips, as I mostly use these or similar.

**Ramius** · - 23rd June 2017, 03:49

I will try that a little later. Right now the program freezes right after the TRISB statement at the Pause 500. Comment out the Pause 500 at it stops at the High Heartbeat! I am so confused!

**aerostar** · - 23rd June 2017, 11:42

I have got the monitor that does NTSC, changing the appropriate bit 8 in the register 14 and with the 14.318 xtal in the STV board, I get a picture with readable text, see below.

However the display is not in the correct place and there is no colour. Further investigation needed!!

It sort of looks like the timing is wrong somewhere probably another setting needs to be changed.

Name: NTSC 1.jpg
Views: 2543
Size: 243.2 KB

Name: NTSC 1.jpg
Views: 2543
Size: 243.2 KB

**Ramius** · - 23rd June 2017, 12:22

Looks Great! I am still stuck with my program freezing right after the TRISB statement at the Pause 500. Comment out the Pause 500 at it stops at the High Heartbeat! I am so confused!

**aerostar** · - 24th June 2017, 13:54

News

I have NTSC display full colour and in the correct position. Problem was low voltage on my STV board, when that was fixed it worked straight away.

Code attached
Program your 628a with the hex code, if it works on your 628A then you have a compiler prob or something, if it does not work you may have a naff 628a.

Also I compile with Picbasic Pro Ver 2.60C - I think you compile using MPLAB, not sure of your PB version, try compiling the 628a code with the PBP compiler.

heartbeat led remarked out

cmcon added in, but not needed as you are not using port A

TRIS B changed to reflect your ports use.

Code:

'****************************************************************
'*  Name    : STV-SYNCHS RELEASE                          *
'*  Author  : BOB LEGGETT                                       *
'*  Notice  : Copyright (c) 2009                                *
'*          : All Rights Reserved                               *
'*  Date    : around 2009 or so rehashed now '17         *
'*  Version : 1.0                                               *
'*  Notes   :   VIDEO IDENT                                *
'*          :                                                   *
'****************************************************************



'   WORKS USES SYNC FOR SWITCHING BETWEEN MIXED AND FULL TEXT MODE
'   GOING FROM VID IN TO TEXT AND BACK TO VID IN

@ device PIC16f628a,HS_OSC,BOD_ON,MCLR_ON,PWRT_ON 

   
        
    define  OSC 20
    
     
'TV CHIP CONNECTIONS
 

 
'---------------------------------------------------------------
   '16f628a  ED definitions
 
 TVSDA     		VAR PORTB.4    '0     OUTPUT  pin 11 stv was b.1
 CS0     		VAR PORTB.6    '0     OUTPUT pin 13 stv was b.0
 TVSCL     		VAR PORTB.5    '0     OUTPUT  pin 12 stv was b.5
 SYNCH0         VAR PORTB.7    '1     'INPUT    to pin 7 stvchip was b.2
 'HEARTBEAT      VAR PORTB.6           'OUTPUT 0  led was b.6
'--------------------------------------------------------------- 

'16f628a 
      
'	  TVSDA     		VAR PORTB.1    '0     OUTPUT  pin 11 stv
' 	CS0     		VAR PORTB.0 '0       OUTPUT pin 13 stv
'	TVSCL     		VAR PORTB.5    '0    OUTPUT  pin 12 stv
'   SYNCH0          VAR PORTB.2 '1       'INPUT    to pin 7 stvchip
'   HEARTBEAT        VAR PORTB.6     'OUTPUT 0  led
'---------------------------------------------------------------

    ZOOMREG         CON %0000000011001100       ' 12 ZOOM REGISTER
    COLREG          CON %0000000011001101       ' 13 COLOUR REGISTER
    CONREG          CON %0000000011001110       ' 14 CONTROL REGISTER
    POSREG          CON %0000000011001111       ' 15 POSITION REGISTER 
    MODEREG         CON %0000000011010000       ' 16 MODE REGISTER

    
      
	ICOUNT  		VAR BYTE
	BITCOUNTER 	VAR BYTE
	WDATA   		VAR WORD
	CHARCOUNTER	VAR BYTE '  
	LINECOUNTER	VAR BYTE '


     STVCHAR VAR BYTE
    ASCCHAR VAR BYTE
    CHARS VAR BYTE
    CHARS2 VAR BYTE
    TEMP    VAR BYTE 
    TEMP1   VAR BYTE
     COUNTER VAR BYTE
     PULSES VAR BYTE
    CURRENTMODE0 VAR BYTE

'----------------------------------------------------------------     
'    TOPLEFT          CON 0
'    TOPMIDDLE       CON 5
'    TOPRIGHT        CON 10
'    BOTLEFT         CON 2560    '10*256
'    BOTMIDDLE       CON 2565 '(10*256)+ 5
'    BOTRIGHT        CON 2570 '(10*256)+ 10
'---------------------------------------------------------------- 

    DATA @0,"NTSC ",$FF,"NO SYNCHS RECEIVED",$FF   



'---------------------------------------------------------------- 
'628
'  TRISB=%10011100
  TRISB = %10001111
  CMCON=7
'----------------------------------------------------------------     


    PAUSE 500
    
'    HIGH HEARTBEAT
    
    
	GOSUB Init
	
    PAUSE 500
	GOSUB Init
    
    CURRENTMODE0=255         ' FORCES TRYSYNCHS TO SET MODE FIRST TIME

	
Demo:

CHARCOUNTER = 0
	LINECOUNTER = 0
'    CURRENTMODE0 = 0     '0 = MIXED 1 = TEXT
    gosub CLS
    GOSUB TRYSYNCHS      '==================================


    TEMP = 0
  
     

LOOPER:
    GOSUB HEADER   ' LINE 3 RIGHT HAND SIDE TEST.
    IF CURRENTMODE0=1 THEN
    GOSUB NOVIDEO   ' DISPLAYS NO VIDEO IF NO INCOMING SYNCHS
    ENDIF

    
    GOSUB TRYSYNCHS       '===========================
    

'    PAUSE 500            'I/2 SECOND DELAY
'    TOGGLE HEARTBEAT      ' LED
    GOTO LOOPER          'DO IT FOREVER
  

DISPLAYCHAR:   

    WDATA = %0001011100000000 + STVCHAR
    GOSUB SEND 
     RETURN
SETLINE:    
	WDATA = LINECOUNTER*256 + CHARCOUNTER
    GOSUB Send              'position cursor   
    RETURN



WasteTime:        ' WORKS WITH LESS NOPS



    pauseus 20    ' was 20 nops

	RETURN

StartCommunication:
	TVSCL = 1 'HIGH TVSCL 
    GOSUB WasteTime

    CS0 = 0 'LOW CS0

    GOSUB WasteTime
	TVSCL = 0 'LOW TVSCL
    GOSUB WasteTime
	RETURN

StopCommunication:
	TVSCL = 1 'HIGH TVSCL
    GOSUB WasteTime
    CS0 = 1 'HIGH CS0

    GOSUB WasteTime
	RETURN

SendOne:
	TVSDA = 1 'HIGH TVSDA
    GOSUB WasteTime
	TVSCL = 0 'LOW  TVSCL
    GOSUB WasteTime
	TVSCL = 1 'HIGH TVSCL
    GOSUB WasteTime
	RETURN

SendZero:
	TVSDA = 0 'LOW TVSDA
    GOSUB WasteTime
	TVSCL = 0 ' LOW TVSCL
    GOSUB WasteTime
	TVSCL = 1 'HIGH TVSCL
    GOSUB WasteTime
	TVSDA = 1 'HIGH TVSDA
    GOSUB WasteTime
	RETURN

OutByte:
	FOR BITCOUNTER = 1 TO 16
	 IF WDATA.15 = 1 THEN
	  GOSUB SendOne
	 ELSE
	  GOSUB SendZero
	 ENDIF
	 WDATA = WDATA << 1
	NEXT BITCOUNTER
	RETURN

Send:
	GOSUB StartCommunication
	GOSUB OutByte
	GOSUB StopCommunication
	RETURN

'-------------------------------------------------------------  

Init:     '    PAUSE 50 added - seems to improve reliability of init

	TVSCL = 1 'HIGH TVSCL
    TVSDA = 1 'HIGH TVSDA
    CS0 = 1 'HIGH CS0
 
	WDATA = $3000  '%110000 00000000
    GOSUB Send ' Init STV5730
    PAUSE 50
	WDATA = $3000
    GOSUB Send
    PAUSE 50
	WDATA = $00DB  '%00000000 11011011
    GOSUB Send
    PAUSE 50
	WDATA = $1000  '%00010000 00000000
    GOSUB Send
    PAUSE 50
'-------------------------------------------------------------  
	WDATA = %0000000011001100
    GOSUB Send ' Init registers (point to register 12)
    PAUSE 50
'-------------------------------------------------------------      
	WDATA = %0001000000000000   'NORMAL
'  WDATA = %0001000011110000   '4 PIXELS HORIZ AND VERT
    GOSUB Send ' Zoom    ADDRESS 12
    PAUSE 50
'-------------------------------------------------------------      
	WDATA = %0001001000000000

'    	WDATA = %0001001000000100
         GOSUB Send ' Color    ADDRESS 13
         PAUSE 50
'--------------------------------------------------------
            
 
     WDATA=  %0001101011010100    'BIT 8 = 0 FOR NTSC

 
     
            'CHANGE BIT 0 TO 1 FOR TEXT ONLY
    GOSUB Send ' Control    ADDRESS 14
'-------------------------------------------------------------    
	WDATA = %0001011111001111
    GOSUB Send ' Position    ADDRESS 15
'------------------------------------------------------------- 

   
	WDATA = %0001000000101110 '$183E BIT 11 CHANGED TO 0  M4 = 0
       GOSUB Send ' Mode    ADDRESS 16  %0001100000111110

'------------------------------------------------------------- 
 
	WDATA = $00C0   '%00000000 11000000
    GOSUB Send ' Set row attributes
     
	FOR ICOUNT = 0 TO 10
	 WDATA = $10C4 '%00010000 11000100
  	' WDATA =%0001000010000111
     GOSUB Send
	NEXT ICOUNT
	RETURN
 
CLS: 
    'character=$0B       'SPACE
     TEMP1=0   ' LINECOUNTER
     TEMP =0    'CHARCOUNTER
loop2:
    
	WDATA = 0  ' LINECOUNTER*256 + CHARCOUNTER   ADDRESS
    GOSUB Send
    

LOOP3:    '                :CHARACTERS        
	WDATA = %0001011100001011  '     1011 0BH SPACECHARACTER
    GOSUB Send
	TEMP = TEMP + 1
	IF TEMP >= 28 THEN
    TEMP = 0
    TEMP1=TEMP1 + 1
	ENDIF
	IF TEMP1 >= 11 THEN SCREENBLANK
 	
    GOTO LOOP3
    
SCREENBLANK:
	RETURN

GETSTVCHAR:                  'CONVERT ASCII TO STV
        STVCHAR =$7F   ' FORCES CLOCK PICTURE IF ERROR         
       LOOKDOWN ASCCHAR,["0123456789- ABCDEFGHIJKLMNOPQRSTUVWXYZ:./'abcdefghijklmnopqrstuvwxyz"],STVCHAR
               RETURN 

HEADER:
    LINECOUNTER=2       'SET START POSITION
    CHARCOUNTER=23      'SET CURSOR POSITION
    GOSUB SETLINE
    FOR CHARS2=0 TO 4
    READ CHARS2, ASCCHAR
    gosub GETSTVCHAR    'CONVERT ASCII TO STV
    GOSUB DISPLAYCHAR
    NEXT
    RETURN
    
NOVIDEO:
    LINECOUNTER=5       'SET START POSITION
    CHARCOUNTER=4       'SET CURSOR POSITION
    GOSUB SETLINE
    FOR CHARS2=6 TO 23      ' FROM EEPROM DATA
    READ CHARS2, ASCCHAR
    gosub GETSTVCHAR    'CONVERT ASCII TO STV
    GOSUB DISPLAYCHAR
    NEXT
    RETURN
    
TRYSYNCHS:
    
    PULSES=0

    COUNT SYNCH0,4,PULSES   '3MS SHOULD COUNT TO 2 OR 3
    IF PULSES > 0 THEN MIXED0
FULL0:

    IF CURRENTMODE0=1 THEN RETURN

    WDATA=  %0000000011001110       'CONTROL REGISTER
    GOSUB SEND
    WDATA=  %0001101011010101   'NTSC

    
    
'        WDATA=  %0001101011010101   'NTSC     BIT 8 = 0
            'CHANGE BIT 0 TO 1 FOR TEXT ONLY       OTIGINAL
            
 '     WDATA=  %0001101111010100
            'CHANGE BIT 0 TO 1 FOR TEXT ONLY        
    GOSUB SEND

STAYHERE02:
  
    CURRENTMODE0=1
        GOSUB CLS
GOBACK0:
    RETURN


MIXED0:
    IF CURRENTMODE0=0 THEN RETURN
    WDATA=  %0000000011001110       'CONTROL REGISTER
    GOSUB SEND
    WDATA=  %0001100111010100    'ntsc
    
    
    
'    WDATA=  %0001101011010100     'NTSC   BIT 8 = 0
    GOSUB SEND

STAYHERE01:

    CURRENTMODE0=0
    GOSUB CLS
    RETURN

HEX code for programmer compiled from above code

Code:

:100000006C28B400841780048413FA30A6000030F2
:10001000A7005120A00AA50AA201A30100083405E7
:10002000A600640000083405A7002606270534064C
:100030000319A20A0319A30A2708A600A403031997
:10004000A5030319A00B11282208672883161C1486
:100050001A0883169B0A6728A301A200FF30A20793
:10006000031CA307031C67280330A100E6303A20D5
:100070002E28A101FC3EA000A109031C4528FF3049
:100080000000A00703184028A0076400A10F3F2824
:1000900008000310A00DA10DFF3E031849282008F9
:1000A00067281030A800A101A001A70CA60C031C12
:1000B0005F282208A00723080318230FA107A10C1B
:1000C000A00CA50CA40CA80B5528240867288313A2
:1000D000031383126400080083168F308600831296
:1000E00007309F000130A300F4302D20DE200130C6
:1000F000A300F4302D20DE20FF30C200BE01C40179
:100100002C21CE21C701A12164004208013C031D1E
:100110008A28B721CE21832800304607BA0017303D
:100120000318013EBB00DA2008004408A600A7011E
:10013000A2010130A3005120B8002508B9003E08F3
:100140003807BA0039080318013EBB00DA2008005E
:100150001430392008008616A8200613A82086121D
:10016000A82008008616A8200617A8200800061652
:10017000A8208612A8208616A82008000612A8200B
:100180008612A8208616A8200616A820080001308E
:10019000BD00640011303D020318D9286400BB1F64
:1001A000D328B720D428BE200310BA0DBB0DBD0F35
:1001B000C9280800AB20C720B22008008616061602
:1001C0000617BA013030BB00DA2032302C20BA01D9
:1001D0003030BB00DA2032302C20DB30BA00BB01DB
:1001E000DA2032302C20BA011030BB00DA20323055
:1001F0002C20CC30BA00BB01DA2032302C20BA01DE
:100200001030BB00DA2032302C20BA011230BB0093
:10021000DA2032302C20D430BA001A30BB00DA2079
:10022000CF30BA001730BB00DA202E30BA001030C1
:10023000BB00DA20C030BA00BB01DA20C301640081
:100240000B30430203182B29C430BA001030BB0016
:10025000DA20C30F1F290800C801C701BA01BB017A
:10026000DA200B30BA001730BB00DA20C70A64006E
:100270001C304702031C3E29C701C80A64000B302A
:10028000480203184429312908007F30C600FF3096
:10029000A200A20A2208433C031CA02955213C02CB
:1002A000031D49292208C600A02901308A0022081E
:1002B0005C3E03188A0A82003034313432343334DD
:1002C0003434353436343734383439342D342034FA
:1002D000413442344334443445344634473448345A
:1002E00049344A344B344C344D344E344F3450340A
:1002F00051345234533454345534563457345834BA
:1003000059345A343A342E342F3427346134623419
:1003100063346434653466346734683469346A3409
:100320006B346C346D346E346F34703471347234B9
:1003300073347434753476347734783479347A3469
:1003400008000230C4001730BE009520C0016400D0
:10035000053040020318B629400883169B0083121B
:100360002620BC0045218C20C00FA729080005309D
:10037000C4000430BE0095200630C0006400183070
:1003800040020318CD29400883169B0083122620C3
:10039000BC0045218C20C00FBE290800C5010430D7
:1003A000A200A3010630840080300120C500640053
:1003B000013045020318EF2964004208013C031D87
:1003C000E2290800CE30BA00BB01DA20D530BA00ED
:1003D0001A30BB00DA200130C2002C210800640072
:1003E0004208003C031DF5290800CE30BA00BB01CD
:1003F000DA20D430BA001930BB00DA20C2012C2137
:020400000800F2
:02400E00663F0B
:104200004E005400530043002000FF004E004F00BA
:104210002000530059004E00430048005300200086
:104220005200450043004500490056004500440047
:02423000FF008D
:00000001FF

Name: NTSC 2.jpg
Views: 2481
Size: 228.5 KB

Thread: A little HELP!!

Thread Tools

Search Thread

Display

Hybrid View

Re: A little HELP!!

Re: A little HELP!!

Re: A little HELP!!

Re: A little HELP!!

Re: A little HELP!!

Re: A little HELP!!

Re: A little HELP!!

Members who have read this thread : 0

Bookmarks

Bookmarks

Posting Permissions