Amicus 18 FTDI driver on W10?

[richard]

hi Henrik
I do it this way , it may not be the best way but it works for me

created folded
c:\myBOOTLOADER
made a subdir for each chip i use
c:\myBOOTLOADER\16f1825
c:\myBOOTLOADER\18f25k22
in each folder the modified config.ini file to suit that chip

to compile loader
copy chosen config.ini to c:\myBOOTLOADER
then using dos shell
cd to working dir
CD C:\Program Files\Mecanique\MCSPX\MCLoader\umc\build
run compiler
umcbuild.exe "c:\myBOOTLOADER\config.ini"

output is in c:\myBOOTLOADER\"chosen pic folder"

note
C:\Program Files\Mecanique\MCSPX\MCLoader\umc\src has two sub dirs
16f and 18f , in these are the device.ini files you may need to add your chips to these files if they are not included


16f1825 ini

; optional path information - default output folder is 
; user documents -> umcbuild... 
[PATH] 
Output=C:\MYBOOTLOADER
[TEMPLATE] 
;PIC18=..\src\18F\umc_loader.asm 
PIC16=..\src\16F\umc_loader.asm 
; device name and OSC... 
[MCU] 
Device=16F1825 
OSC=32000000 
[USART] 
BAUDRATE = 19200 ; initial startup baudrate (default is 19200) 
BRGH16 = 1 ; 16 bit SPBRG support (default is OFF) 
; device configuration settings... 
[CONFIG] ;----- CONFIG1 Options -------------------------------------------------- 
 __config        _CONFIG1,    _FOSC_INTOSC & _CP_OFF & _WDTE_OFF  &  _PWRTE_ON  &  _MCLRE_ON  & _CLKOUTEN_OFF
 __config      _CONFIG2, _PLLEN_OFF & _LVP_OFF
; place startup code in here... 
[USERCODE] 

 movlb 1
 BCF TRISC,4
 BSF TRISC,5
 ;movlb 1
 movlw 0xF0 ; 32 MHz
 movwf OSCCON
 btfss OSCSTAT,6
 goto $-1

1825k22 ini

; optional path information - default output folder is 
; user documents -> umcbuild... 
[PATH] 
Output=C:\MYBOOTLOADER
; source code files... 
[TEMPLATE] 
PIC16=..\src\16F\umc_loader.asm 
PIC18=..\src\18F\umc_loader.asm 
[USART] BAUDRATE=19200 BRGH=1 BRG16=1 
; device name and OSC... 
[MCU] 
Device=18F25K22 
OSC=64000000 
; device configuration settings... 
[CONFIG] 
config FOSC = INTIO67
config PLLCFG = OFF
config PRICLKEN = ON ; Primary clock Enabled 
config FCMEN = OFF ; Fail-Safe Clock Disabled 
config IESO = OFF ; Oscillator Switchover Disabled 
config PWRTEN = ON ; Powerup Timer Enabled 
config HFOFST = OFF ; HFINTOSC delayed until oscillator stable 
config BOREN = ON ; Brown Out Detector Enabled 
config BORV = 250 ; VBOR set to 2.50 V nominal 
config WDTEN = OFF ; WDT Enabled; SWDTEN bit has no effect 
config WDTPS = 512 ; WDT = 1:512 = 2048 ms 
config CCP2MX = PORTB3 ; CCP2 i/o is multiplexed with RB3 (not RC1) 
config CCP3MX = PORTB5 ; P3A/CCP3 i/o is multiplexed with RB5 (not RC6) 
config T3CMX = PORTB5 ; T3CKI is on RB5 (not RC0) 
config P2BMX = PORTC0 ; ECCP2 P2B is on RC0 (not RB5) 
config PBADEN = OFF ; PORTB<5:0> pins configured as digital i/o (not analog) 
config MCLRE = EXTMCLR 
config STVREN = ON ; Stack Overflow Reset Enabled 
config XINST = OFF ; Extended Instructions Disabled 
config LVP = OFF ; Low-Voltage-Programming Disabled 
config CP0 = OFF ;Code Protect 00800-03FFF 
config CP1 = OFF ;Code Protect 04000-07FFF 
config CP2 = OFF ;Code Protect 08000-0BFFF 
config CP3 = OFF ;Code Protect 0C000-0FFFF 
config CPB = OFF ;Code Protect Boot 
config CPD = OFF ;Data EE Read Protect 
config WRT0 = OFF ;Table Write Protect 00800-03FFF 
config WRT1 = OFF ;Table Write Protect 04000-07FFF 
config WRT2 = OFF ;Table Write Protect 08000-0BFFF 
config WRT3 = OFF ;Table Write Protect 0C000-0FFFF 
config WRTC = OFF ;Config. Write Protect 
config WRTB = OFF ;Table Write Protect Boot 
config WRTD = OFF ;Data EE Write Protect 
config EBTR0 = OFF ;Table Read Protect 00800-03FFF 
config EBTR1 = OFF ;Table Read Protect 04000-07FFF 
config EBTR2 = OFF ;Table Read Protect 08000-0BFFF 
config EBTR3 = OFF ;Table Read Protect 0C000-0FFFF 
config EBTRB = OFF ;Table Read Protect Boot 
; place startup code in here... 
[USERCODE] 
movlb 0x0F ; MANDATORY: BSR set to SFR bank 
movlw b'00000000' 
movwf ANSELC ; MANDATORY: analog off on port C 
movlw 0x70 
movwf OSCCON
bsf   OSCTUNE,6
BTFSS OSCCON2,7
BRA $-2