Interrupts Revisited

[yettie]

rob,

i think he had the same problem in using the ON INTERRUPT method. maybe you would want to consider the ASM interrupts. Its a lot more easier than microcode interrupt. just for an idea.

DEFINE INTHAND IntHandler
...(define your variables)

;-------------
Initialize:
TRISB = $FF
INTCON = %11001000 ;(enable portb change interrupt)
OPTION_REG = $7F ;(pulls ups enable)
... (then your main routines)

;------------------
@_IntHandler ;Interrupt Service Routine
INTCON.3 = 0 ; disable portb change interrupt while in this routine
;(reset all necessary variables and call your extra routines)
INTCON.3 = 1 ; reenable portb change interrupt
@retfie


Well I hope this one will give you some ideas. ON INTERRUPT is hard to implement with so much latency compared asm interrupt. As another advatage, you saved some words since ON INTERRUPTS have so many overheads inserted per each of your line since it polls interrupt flags. ok?

regards,
Paul

[yettie]

in addition to this, save all your status, W and other registers if necessary when the program is interrupted. just reload it later. in your case i don't think you will to save your last state when interrupted, or just correct me if im wrong.

regards,
yettie

[Rob Martin]

The routine I call outside of the ISR has DISABLE & ENABLE either side of it.
It was my understanding that I can call this other routine and that it will complete the routine then jump back to the ISR.

This part appears to work fine. My problem is/was that even when an interrupt hasn't occured my code inside the ISR seems to the execute?
(it seems to execute the "ELSE" statments)

Can someone confirm I have the correct flags bits set and clear for the "on change" interrupt.

Lastly having local VARS, I have compiled like this before and never had a problem. Does the compiler just pick the VAR out at compilation time regardless of where they are?
Again with the ON INTERRUPT call does this need to be anywhere specific? it seems to my no difference where I put it.

Rob

[Bruce]

Try adding this to the end of your ISR before returning;

Dummy = PORTB ' read port into Dummy var to end missmatch condition
INTCON.0 = 0 ' clear RB interrupt flag bit

Clearing INTCON.1 clears RB0/INT External Interrupt Flag bit. Not RB interrupt on change.

[Rob Martin]

Bruce

Let me take one step back.
Here is the code I used originally to test my PCB
You said I was clearing the RB0 flag which I agree with but unless I clear this the program doesn't work!!
If I use the INTCON.0 = 0 the code doesn't work but using INTCON.1=0 makes the program work.
I'm very confused and going round in circles as what I would expect to work doesn't. Do I need to enable the Global interrupt GIE INTCON.7=1 before exiting the ISR?

I've reread the 16f877 data sheet and what I'm doing shouldn't work, but it does.

Rob



***************************************

DEFINE LOADER_USED 1 'Boot Loader
'Define inputs held low by external resistors
sw1 VAR PORTB.6
sw2 VAR PORTB.4
SW3 VAR PORTB.0
' Define the pins that are connected to LEDs
led1 VAR PORTC.0
led2 VAR PORTC.1

INTCON.3 = 1 ' Enable the RB port change interrupt
OPTION_REG = $7f ' Enable PORTB pull-ups
TRISC = %00000011 ' Set PORTB.0-2 (LEDs) to output, 3-7 to input
on interrupt goto ISR

main: ' main program begins here


' Check any button pressed to toggle on LED


NAP 7 ' Go to sleep. When the watchdog is
' disabled, NAP won't wake up until
' an interrupt occurs.

GoTo main ' Do it again upon waking
DISABLE
:ISR
IF sw1 = 1 Then
high LED1
else
low led1
endif

IF sw2 = 1 Then
HIGH led2
else
low led2
endif

IF sw3 = 1 Then
HIGH led1
HIGH led2
else
low led1
low led2
endif
'***HERE*************
'INTCON.0 = 0 ' Clear the RB port change flag bit( this doesn't)
INTCON.1 = 0 ' Clear interrupt flag (this works)

RESUME
ENABLE

[Bruce]

INTCON.3 = 1 turns ON RB Port Change Interrupt Enable bit. This means any change on RB7, 6, 5 or 4 will generate the interrupt.

There are a few things to watch out for when using this.

1. Set the upper 4-bits up as inputs. TRISB = %11110000 (assumes only top 4 are used as inputs) change as required. And make sure these inputs are not floating by using internal or external pull-ups - or external pull-downs depending on your switch open/close logic.

2. Do a "read" of the port before turning ON RB int change. Dummy = PORTB.
Just take a snap-shot of portb inputs before turning the option on.

3. INTCON.3 = 1 Now any change from the last value read on RB7,6,5 or 4 will cause the interrupt flag bit INTCON.0 to be set (RBIF: RB Port Change Interrupt Flag bit)

Now, before exiting your ISR, you need to read portb again, then clear the flag bit associated with RB int change.

Dummy = portb ' end missmatch
INTCON.0 = 0 ' clear interrupt flag bit before re-enabling interrupts
RESUME
ENABLE

Some other things to consider.

You're testing upper portb pins in your ISR. This actually reads the port, and will end the missmatch, BUT, your program is going to run much faster than than anyone can operate a push-button switch, and you will have switch bounce.

What can happen is you enable RB int on change, someone releases the switch, and you have the interrupt "missmatch" condition all over again.

You might want to include some code that recognizes the keypress, and then waits for the user to release the key before reading the port, and re-enabling the interrupt on change. You can turn ON the LED immediately, but wait for the key to be released before reading the port & re-enabling int on change.

Also, you're turning ON internal pull-ups, and you're testing input pins for logic 1 with IF SW1 = 1 THEN do something.

What logic level does a switch press apply to your switch inputs?

Do I need to enable the Global interrupt GIE INTCON.7=1 before exiting the ISR?
Definitely not. Exiting the interrupt with RESUME, ENABLE handles everything for you. Using ON INTERRUPT you never need to mess with GIE unless you want to totally disable interrupts. In that case write INTCON = $80 like shown in your manual.

[crematory]

Hello

Good answer bruce, really good one

Any way, to solve your problem, here is what you have to do, as it worked for me:

1. Read portb.
2. Clear the GIE and portb on change IE bit.
3. Pause for, say 100 to 150 ms, to ensure that the user has releasd the button.
4. Do what you want to do. Use the first value you read for portb.
5. Now set RB on change IE bit.
6. Then read portb again, to clear any "may be" pending interrupts, don't try to read portb before enabling RB IE bit, as this is certainly will not be sufficent.
7. Resume will enable GIE bit.

I wish I had that code, I formatted the C partition, and forgot to move some files, that was one of them