Code:
' config for 18F46K80
#CONFIG
;----- CONFIG1L Options --------------------------------------------------
CONFIG XINST = OFF
CONFIG SOSCSEL = DIG ; Digital (SCLKI) mode; I/O port functionality of RC0 and RC1 is enabled
CONFIG INTOSCSEL = LOW ; LF-INTOSC in low-power mode during Sleep
CONFIG RETEN = ON ; Ultra Low power regulator is Enabled (Controlled by SRETEN bit)when in sleep
;----- CONFIG1H Options --------------------------------------------------
CONFIG IESO = OFF
CONFIG FCMEN = OFF
CONFIG PLLCFG = OFF
CONFIG FOSC = INTIO2 ; Internal RC oscillator , PORTA.6 , PORTA.7 as I/O
;----- CONFIG2L Options --------------------------------------------------
CONFIG BORPWR = ZPBORMV ; ZPBORMV instead of BORMV is selected
CONFIG BORV = 2 ; 2V
CONFIG BOREN = SBORDIS ; Enabled in hardware, SBOREN disabled
CONFIG PWRTEN = OFF
;----- CONFIG2H Options --------------------------------------------------
CONFIG WDTPS = 512 ; 1:512
CONFIG WDTEN = OFF ; WDT Off
;----- CONFIG3L Options --------------------------------------------------
; no register in the device
;----- CONFIG3H Options --------------------------------------------------
CONFIG MCLRE = ON ; MCLR ENabled FOR DIAG , RG5 DISabled
CONFIG MSSPMSK = MSK7 ; 7 Bit address masking mode
CONFIG CANMX = PORTB ; ECAN TX and RX pins are located on RB2 and RB3, respectively
;----- CONFIG4L Options --------------------------------------------------
CONFIG BBSIZ = BB1K ; 1K word Boot Block size
CONFIG STVREN = ON
;----- CONFIG5L Options --------------------------------------------------
CONFIG CP0 = ON ; MEMORY BLOCK 0 CODE PROTECT BIT - 7KW 800h - 3FFFh ( when 1K BOOT OPTION used )
CONFIG CP1 = ON ; MEMORY BLOCK 1 CODE PROTECT BIT - 8KW 4000h - 7FFFh
CONFIG CP2 = ON ; MEMORY BLOCK 2 CODE PROTECT BIT - 8KW 8000h - BFFFh
CONFIG CP3 = ON ; MEMORY BLOCK 3 CODE PROTECT BIT - 8KW C000h - FFFFh
;----- CONFIG5H Options --------------------------------------------------
CONFIG CPD = OFF ; EEPROM DATA PREOTECT BIT - EXTERNAL R/W
CONFIG CPB = ON ; BOOT BLOCK CODE PROTECT BIT
;----- CONFIG6L Options --------------------------------------------------
CONFIG WRT0 = OFF ; MEMORY BLOCK WRITE PROTECT BIT
CONFIG WRT1 = OFF
CONFIG WRT2 = OFF
CONFIG WRT3 = OFF
;----- CONFIG6H Options --------------------------------------------------
CONFIG WRTD = OFF ; EEPROM WRITE PROTECT BIT - INTERNAL AND EXTERNAL
CONFIG WRTB = ON ; BOOT BLOCK WRITE PROTECT
CONFIG WRTC = ON ; CONFIGURATION REGISTER WRITE PROTECT BIT
;----- CONFIG7L Options --------------------------------------------------
CONFIG EBTR0 = OFF ; MEMORY READ TABLE BLOCK PROTECT
CONFIG EBTR1 = OFF
CONFIG EBTR2 = OFF
CONFIG EBTR3 = OFF
;----- CONFIG7H Options --------------------------------------------------
CONFIG EBTRB = OFF ; TABLE READ PROTECT BOOT
#ENDCONFIG
clear ' clear all varables to 0 on startup
' ---------------- Setup All Define statements ------------
DEFINE OSC 4 ' Timing referance for pause , pauseus commands
DEFINE ADC_BITS 12 ' Number of bits in ADCIN result - Required for adcin command
DEFINE PULSIN_MAX 2000 ' Maximum counts( clock ticks) allowed before pulsin times out( 2000 ^ 1.25us = 2.5 ms)
DEFINE HSER_PORT 2 ' Hser port 2 use
DEFINE HSER2_RCSTA 90h ' Hser2 receive status init
DEFINE HSER2_TXSTA 24h ' Hser2 transmit status init ( BIT2 -BRGH 1= HI SPEED, 0= LOW SPEED )
DEFINE HSER2_CLROERR 1 ' Clear overflow automatically
DEFINE HSER2_BAUD 19200 ' Hser2 baud rate
DEFINE HSER2_SPBRG 12 ' 19200 Baud @ SPBRGH = 12 0.16% error
BAUDCON2.3 = 1 ' set BRG16 = 1 - 16BIT/ASYNC
' ---------- Set up DT_INTS-18 Routine for Instant Interupt handling -----------
INCLUDE "DT_INTS-18.bas" ; Base Interrupt System for 18FxxK80 processors
INCLUDE "ReEnterPBP-18.bas" ; Include if using PBP interrupts
ASM
INT_LIST macro ; IntSource , Label , Type, ResetFlag?
INT_Handler TMR0_INT, _Timer0_Count, PBP, yes ; call Timer0_Count subroutine
INT_Handler RBC_INT, _Rx_mode_IOC , PBP, yes ; Call Rx_mode_IOC subroutine for RF RX_mode
INT_Handler RX2_INT, _Term_RX , PBP, yes ; Call Term_input for terminal char buffer
INT_Handler INT0_INT, _Sleep_Over , PBP, Yes ; Call for INT0 trigger - when exit sleep mode
endm
INT_CREATE ; Creates the Interrupt Processor
ENDASM
'----------- 18F46K80 - PIC chip Dephalt settings --------------------
OSCCON = %00110000 ' Select 1Mhz - using 1Mhz internal with PPLx4 in Config1H<3:0> = IDLEN =0 , 8Mhz , OSTS=0,RFIOFS=1,RC_Run (1x) OSC using PLL
' Bit 7 IDLEN =0 ( sleep mode when sleep instraction executed)
' Bits 6-4 - 111 = 16Mhz , 110 = 8MHz ,101 = 4 MHz, 100 = 2MHz 011 = 1MHz
' If INTTSRC=0 and MFIOSEL= 0 then 010 = HF-INTOSC/32 (500Khz), 001 = HF-INTOSC/64 (250Khz) ,000 = LF-INTOSC (31.25Khz)
' If INTTSRC=0 and MFIOSEL= 1 then 010 = MF-INTOSC (500Khz), 001 = MF-INTOSC/2 (250Khz) ,000 = LF-INTOSC (31.25Khz)
' If INTTSRC=1 and MFIOSEL= 0 then 010 = HF-INTOSC/32 (500Khz), 001 = HF-INTOSC/64 (250Khz) ,000 = HF-INTOSC/512 (31.25Khz)
' If INTTSRC=1 and MFIOSEL= 1 then 010 = MF-INTOSC (500Khz), 001 = MF-INTOSC/2 (250Khz) ,000 = MF-INTOSC/16 (31.25Khz)
' Note: INTSRC = OSCTUNE<7> and MFIOSEL = OSCCON2<0>
' Bit 3 - OSTS = 0 - Osc startup time out is ruinning from internal OSC ( HF, MF or LF-INTOSC)
' Bit 2 - HFIOFS =1 ( INTOSC Frq stable bit - 1 = stable , 0 = not stable
' Bits 1-0 - 00= Dephalt Pri OSc ( OSC1/2 or HF-INTOSC with/without PLL set in FOSC,3:0> config1H <3.0>
' 01 = SOSC osc
' 1x = Internal osc ( LF, MF,HF-INTOSC)
' OSCCON2 = $00 ' Bit 7 n/a , Bit 6 - SOSCRUN - Run status bit , Bit 5-4 n/a,
' Bit 3 = SOASCGO - Osc Start control bit 1 = OSC running , 0 = OSC shut off if no requests for it
' Bit 2 n/a , Bit 1 - MFIOFS 1= MFINTOSC stable 0 = Not stable
' Bit 0 MFIOSEL - 1 = MF-INTOSC replaces HF-ISTOSC Freq for 500Khz,250Khz,31.25KHz) 0 = MF-INTOSC not used
OSCTUNE = %01000000 ' Bit 7 - INTSRC - internal LF Source Select 1 = 31.25 from 16Mhz Internal /512 HF-INTOSC ) 0 = Internal 31khz OSC
' Bit 6 - PLLEN - 1 PLL enabled , 0 = PLL disabled
' Bits 5-0 Frequancy callibaration 00000 = centre Frq
WDTCON = %00010000 ' use ultra low power mode when in sleep - disable regulator in sleep mode
' Bit7 = REGSLP- Regulator Voltage Sleep Enable - 1= Reg goes into low-power Mode when in sleep mode ,0 = Reg stay in normal mode
' Bit6= n/a , Bit5 = ULPLVL - Ultra lowpower Wakeup output sel 1= Vout on RA0 0= Vout on RA1 ( no effect if WDTEN in config is set )
' Bit4= SRETEN = Regulator Volt Sleep Disable bit - 1= goes into Ultra lOwpower mode in sleep ( CONFIG1L.0 =0 MUST BE SET)
' Bit3=n/a , Bit2 = ULPEN - Ultra Low Power Wakup Module enable 1 = enabled , 0 = disabled
' Bit1=ULPSINK- Ultra Low-power Wakeup Current Sink Enable 1= Sink enabled 0 = Sink disabled ( Not valid if ULPEN=0 )
' Bit0= SWDTEN -Watchdog Timer Enable = 1= enable watchdog 0 = Disable Watchdog ( no effect if WDTEN in config is set )
PSPCON.4 = 0 ' turn off parallel slave port mode - general purpose I/O mode PORTD & PORTE
INTCON2.6 = 0 ' INTEDG0 - External Interrupt 0 Edge Select - 1= Rising Edge , 0 = Falling Edge
INTCON2.5 = 0 ' INTEDG1 - External Interrupt 1 Edge Select - 1= Rising Edge , 0 = Falling Edge
INTCON2.4 = 0 ' INTEDG2 - External Interrupt 2 Edge Select - 1= Rising Edge , 0 = Falling Edge
INTCON2.3 = 0 ' INTEDG3 - External Interrupt 3 Edge Select - 1= Rising Edge , 0 = Falling Edge
INTCON3.6 = 0 ' INT1IP - INT1 External Interupt Priority - 1 = High Priorty , 0 = Low Priority
INTCON3.7 = 0 ' INT2IP - INT2 External Interupt Priority - 1 = High Priorty , 0 = Low Priority
INTCON2.1 = 0 ' INT3IP - INT3 External Interupt Priority - 1 = High Priorty , 0 = Low Priority
Re: USART2 setting for 1MHzCPU + 4PLL
Bookmarks