12F1840 config issues

Closed Thread
Results 1 to 14 of 14

Hybrid View

  1. - 10th February 2015, 19:38 #1
    enigma's Avatar
    enigma
    enigma is offline Junior Member
    Join Date
    Jul 2003
    Location
    Lancashire
    Posts
    50

    Default 12F1840 config issues

    Hi All
    I searched for an answer to this but came up blank. The program has been reduced to a single serout2 command to test. It works fine on both a 12F683 and 16F688 with the correct configs but I cant seem to get it to function on the 12F1840. There is data out but its garbage and clearly the wrong baud rate. I suspect I have not configured something, probably the oscillator correctly so requesting help. Its probably obvious but I cant spot it.
    Cheers Pete

    Code: PBP3
    Code:
    #CONFIG

	__CONFIG	_CONFIG1, _FOSC_INTOSC & _WDTE_ON & _PWRTE_ON & _MCLRE_ON & _BOREN_OFF
	__CONFIG	_CONFIG2, _PLLEN_ON & _BORV_LO & _LVP_OFF

#ENDCONFIG

OPTION_REG	= %10000001
WPUA		= %00000000    'weak pull ups disabled
ANSELA             = %00000000    'Select all digital
TRISA               = %00001101	   ' Make A0,A2,A3 inputs,A1,A4,A5 outputs
                           
OSCCON      = %11110000    'SET INTOSC TO 32MHZ 
OSCTUNE     = %00000000

INTCON 		= 0            'Latch out interrupt
CM1CON0		= 0            'disable  comparators
FVRCON		= 0            'Fixed voltage reference disabled


DEFINE OSC 32

Test:
serout2 PORTA.5,16468,["Testing",13,10]

pause 1000
goto Test
    Last edited by Archangel; - 14th February 2015 at 10:22.
  2. - 10th February 2015, 20:55 #2
    Acetronics2's Avatar
    Acetronics2
    Acetronics2 is offline Fanatical Contributor
    Join Date
    May 2004
    Location
    NW France
    Posts
    3,653

    Did you find this post helpful? Yes | No

    Default Re: 12F1840 config issues

    Hi Enigma

    Code:
    ' Config
'*******************************************************************************

#IF __PROCESSOR__ = "12F1840"

 #CONFIG
	__CONFIG    _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_ON  & _MCLRE_OFF & _CP_OFF  & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_OFF & _FCMEN_OFF
 	__CONFIG 	_CONFIG2, _WRT_ALL & _PLLEN_ON & _STVREN_OFF & _BORV_LO & _LVP_OFF
#ENDCONFIG

#ELSE
    #MSG "Wrong Processor selected!"
#ENDIF

'*****************************************************************************
'Includes
'*****************************************************************************

INCLUDE "DT_INTS-14-2k.bas"
INCLUDE "ReEnterPBP.bas"

ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?

     	INT_Handler    TMR1_INT,  _ClockCount,   PBP,  yes
           
    endm
    INT_CREATE            ; Creates the interrupt processor
ENDASM


INTCON.7 = 0				' Pour čtre sur !!!

'*******************************************************************************
' Ports init

TRISA		= 0
PORTA 		= 0
LATA		= 0

NeoPinW1     VAR LATA.0
NeoPinW2     VAR LATA.1
NeoPinR		 VAR LATA.2

'*******************************************************************************
' Chip  Initialization 

OSCCON  = %11110000 ' 8 Mhz internal x 4
OSCTUNE	= %00000000	' Internal osc Adjustment

WHILE !OSCSTAT.3	' Wait for stable OSC ...
WEND

INTCON	= 0
CPSCON0 = 0
CPSCON1 = 0 
ADCON0 	= 0
ADCON1	= %10000000
ANSELA 	= 0
CCP1CON = 0
CM1CON0 = 0
DACCON0 = 0
FVRCON	= 0

' Timer 1 

T1CON 	= %00110101		' Preload @ 15536, PS=8, run
T1GCON 	= 0
INTCON	= %11000000
PIE1	= %00000001
PIR1	= 0
    This config works ...

    But I remember It was somewhat tricky ...

    I think this
    Code:
    WHILE !OSCSTAT.3	' Wait for stable OSC ...
WEND
    made the chip run fine ...

    Alain
    ************************************************** ***********************
    Why insist on using 32 Bits when you're not even able to deal with the first 8 ones ??? ehhhhhh ...
    ************************************************** ***********************
    IF there is the word "Problem" in your question ...
    certainly the answer is " RTFM " or " RTFDataSheet " !!!
    *****************************************
  3. - 11th February 2015, 14:12 #3
    Charlie's Avatar
    Charlie
    Charlie is offline Senior Member
    Join Date
    Dec 2010
    Posts
    409

    Did you find this post helpful? Yes | No

    Default Re: 12F1840 config issues

    Your clock setup looks fine, but you can always do a blink test to confirm.
    However, what baud rate are you trying to achieve? 16468 seems to be about 60 baud by my calculations?
  4. - 11th February 2015, 15:09 #4
    Dave's Avatar
    Dave
    Dave is offline Prolific Poster
    Join Date
    Mar 2003
    Location
    Commerce Michigan USA
    Posts
    1,166

    Did you find this post helpful? Yes | No

    Default Re: 12F1840 config issues

    It looks like 9600 baud by my calculations w/ open wire mode enabled. As far as the config's go everything looks good. Here is my config's for a Waterstick I designed and works great.
    Code:
    DEFINE OSC 32

#CONFIG
;----- CONFIG1 Options --------------------------------------------------
  __config _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_ON & _MCLRE_OFF & _CP_OFF & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_ON & _FCMEN_ON

;----- CONFIG2 Options --------------------------------------------------
  __config _CONFIG2, _WRT_OFF & _PLLEN_ON & _STVREN_ON & _BORV_19 & _LVP_OFF
#ENDCONFIG

' ********************************************************************
'				SYSTEM INITIALIZATION
' ********************************************************************
	clear
	PORTA = %00000000
	TRISA = %00001111	'INITIALIZE PORT DIRECTIONS
	OSCCON = %11110000	'PLL ENABLED,8Mhz,FSOSC<2:0>
   	INTCON = %00000000 'CLEAR GIE,PEIE,TMR0IE,INTE,RBIE,TMR0IF,INTF,RBIF
   	PIE1 = %00000000    'CLEAR ALL INTERRUPT ENABLE BITS
   	PIR1 = %00000000    'CLEAR ALL INTERRUPT FLAGS
  	PIE2 = %00000000    'CLEAR ALL INTERRUPT ENABLE BITS
  	PIR2 = %00000000    'CLEAR ALL INTERRUPT FLAGS
	APFCON = %00000000	'ALL DEFAULTS
	ANSELA = %00000011	'AN0:AN1 ANALOG,AN2:AN4 DIGITAL I/O
	CPSCON0 = %11001100	'ENABLE CAP SENSE,DAC/FVR,HIGH RANGE
	WPUA = %00001100	'WEAK PULLUP'S OFF, EXCEPT A.2,A.3
  	ADCON0 = %00000000  'CHS2:0,GO/DONE,ADOFF
  	ADCON1 = %11100000  'RIGHT JUSTIFIED,FOSC/64,VSS,VDD
	SRCON0 = %00000000
	SRCON1 = %00000000
   	CM1CON0 = %00000000	'CLEAR/DISABLE COMPARATOR
   	CM1CON1 = %00000000	'CLEAR/DISABLE COMPARATOR
  	CMOUT = %00000000	'DISABLE OUTPUT REGISTER
   	DACCON0 = %11001000	'ENABLE DAC,ENABLE POS REFERENCE,SOURCE IS FVR
   	DACCON1 = %00001000	'SET FOR 1/4 SCALE (8) ~ 1.024
  	FVRCON = %10001100	'ENABLE VOLTAGE REFERENCE,4,096
   	OPTION_REG = %00000000 'INTEDG,T0CS,T0SE,PSA,PS
   	T1CON = %11000001	'CAPOSC INPUT,PRESCALER 1/1,START TIMER 1
   	T1GCON = %00000000	'NO GATE CONTROL
   	T2CON = %00000000	'POSTSCALER 1/1,STOP,PRESCALER 1
   	TMR2 = 0			'CLEAR TMR2 MODULE REGISTER
   	PR2 = 255			'SET PERIOD ((((1 / 32,000,000)*4) * 1 PRESCALE) * (1+255 PR2)) = 31.25 KHZ.
   	CCP1CON = %00000000	'PLACE CCP1 INTO DISABLE MODE
   	CCPR1L = $00		'CLEAR CCP1 LOWER 8 BITS
   	CCPR1H = $00		'CLEAR CCP1 UPPER 2 BITS
	PSTR1CON = %00000001'DEFAULT
    Last edited by Archangel; - 14th February 2015 at 10:21. Reason: code tags
    Dave Purola,
    N8NTA
    EN82fn
  5. - 11th February 2015, 16:34 #5
    enigma's Avatar
    enigma
    enigma is offline Junior Member
    Join Date
    Jul 2003
    Location
    Lancashire
    Posts
    50

    Did you find this post helpful? Yes | No

    Default Re: 12F1840 config issues

    Many thanks, I will run through these and see. These seem tricky beasts to set up and I am sure I have probably not set something I need to. Will report back! Cheers Pete
  6. - 12th February 2015, 09:36 #6
    enigma's Avatar
    enigma
    enigma is offline Junior Member
    Join Date
    Jul 2003
    Location
    Lancashire
    Posts
    50

    Did you find this post helpful? Yes | No

    Default Re: 12F1840 config issues

    I now have the code below. The serial data appears to come out at intervals of one second but is complete garbage still. Replacing the PIC with an appropriately configured 12F683 all functions fine. I am wondering if anyone else can replicate a serout2 on the 12F1840 and see if its the same. If the code looks good I am wondering if its a problem with PBP?. Cheers Pete

    Code:
    :
#CONFIG
 ;----- CONFIG1 Options --------------------------------------------------
 __config _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_ON & _MCLRE_ON & _CP_OFF & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_ON & _FCMEN_ON

 ;----- CONFIG2 Options --------------------------------------------------
 __config _CONFIG2, _WRT_OFF & _PLLEN_ON & _STVREN_ON & _BORV_19 & _LVP_OFF
 #ENDCONFIG

 ' ************************************************** ******************
 ' SYSTEM INITIALIZATION
 ' ************************************************** ******************
 clear
 'PORTA = %00000000
 TRISA  = %00001101	   ' Make A0,A2,A3 inputs,A1,A4,A5 outputs
 OSCCON = %11110000 'PLL ENABLED,8Mhz,FSOSC<2:0>
 OSCTUNE	= %00000000	' Internal osc Adjustment
WHILE !OSCSTAT.3	' Wait for stable OSC ...
WEND
 INTCON = %00000000 'CLEAR GIE,PEIE,TMR0IE,INTE,RBIE,TMR0IF,INTF,RBIF
 PIE1 = %00000000 'CLEAR ALL INTERRUPT ENABLE BITS
 PIR1 = %00000000 'CLEAR ALL INTERRUPT FLAGS
 PIE2 = %00000000 'CLEAR ALL INTERRUPT ENABLE BITS
 PIR2 = %00000000 'CLEAR ALL INTERRUPT FLAGS
 APFCON = %00000000 'ALL DEFAULTS
 ANSELA      = %00000000    'Select all digital
 CPSCON0 = %11001100 'ENABLE CAP SENSE,DAC/FVR,HIGH RANGE
 WPUA		= %00000000    'weak pull ups disabled
 ADCON0 = %00000000 'CHS2:0,GO/DONE,ADOFF
 ADCON1 = %11100000 'RIGHT JUSTIFIED,FOSC/64,VSS,VDD
 SRCON0 = %00000000
 SRCON1 = %00000000
 CM1CON0 = %00000000 'CLEAR/DISABLE COMPARATOR
 CM1CON1 = %00000000 'CLEAR/DISABLE COMPARATOR
 CMOUT = %00000000 'DISABLE OUTPUT REGISTER
 DACCON0 = %11001000 'ENABLE DAC,ENABLE POS REFERENCE,SOURCE IS FVR
 DACCON1 = %00001000 'SET FOR 1/4 SCALE (8) ~ 1.024
 FVRCON = %10001100 'ENABLE VOLTAGE REFERENCE,4,096
 OPTION_REG = %00000000 'INTEDG,T0CS,T0SE,PSA,PS
 T1CON = %11000001 'CAPOSC INPUT,PRESCALER 1/1,START TIMER 1
 T1GCON = %00000000 'NO GATE CONTROL
 T2CON = %00000000 'POSTSCALER 1/1,STOP,PRESCALER 1
 TMR2 = 0 'CLEAR TMR2 MODULE REGISTER
 PR2 = 255 'SET PERIOD ((((1 / 32,000,000)*4) * 1 PRESCALE) * (1+255 PR2)) = 31.25 KHZ.
 CCP1CON = %00000000 'PLACE CCP1 INTO DISABLE MODE
 CCPR1L = $00 'CLEAR CCP1 LOWER 8 BITS
 CCPR1H = $00 'CLEAR CCP1 UPPER 2 BITS
 PSTR1CON = %00000001'DEFAULT 
 FVRCON		= 0            'Fixed voltage reference disabled

DEFINE OSC 32

initialise:
serout2 PORTA.5,16468,["Waiting for X200",13,10]
pause 1000
goto initialise
    Last edited by Archangel; - 14th February 2015 at 10:13.
« Previous Thread | Next Thread »

Similar Threads

  1. Problem converting 12F683 code to 12F1840
    By RossWaddell in forum mel PIC BASIC Pro
    Replies: 7
    Last Post: - 14th March 2013, 01:55
  2. PBP Support for 12F1840 8-Pin Device?
    By springtank in forum mel PIC BASIC Pro
    Replies: 17
    Last Post: - 10th November 2012, 08:32
  3. Timer1 issues
    By mitchf14 in forum mel PIC BASIC Pro
    Replies: 1
    Last Post: - 9th January 2009, 16:21
  4. 12c508a Device Config. And Burning Issues
    By sayzer in forum mel PIC BASIC Pro
    Replies: 4
    Last Post: - 29th March 2006, 16:50

Members who have read this thread : 0

You do not have permission to view the list of names.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules