Hi Richard

Thank you for reply... Here is code to date.... With most recent error.

Code:
'****************************************************************
'*  Name    : COMPASS_818.BAS                                      *
'*  Author  : [select VIEW...EDITOR OPTIONS]                    *
'*  Notice  : Copyright (c) 2014 [select VIEW...EDITOR OPTIONS] *
'*          : All Rights Reserved                               *
'*  Date    : 24/08/2014                                        *
'*  Version : 1.0                                               *
'*  Notes   :                                                   *
'*          :                                                   *
'****************************************************************



' LCD should be connected as follows:
'       LCD     PIC
'       DB4     PortA.0
'       DB5     PortA.1
'       DB6     PortA.2
'       DB7     PortA.3
'       RS      PortA.4 (add 4.7K (10k)pullup resistor to 5 volts)
'       E       PortB.3
'       RW      Ground
'       Vdd     5 volts
'       Vss     Ground
'       Vo      5K potentiometer (or ground)
'       DB0-3   No connect





    adcon1 = 7     ' Turns Analogs off
    
    DEFINE OSC 12	'Set oscillator in MHz
    'OSCCON = $70
    DEFINE LCD_EREG PORTB
    DEFINE LCD_EBIT 6
    DEFINE LCD_RSREG PORTB
    DEFINE LCD_RSBIT 7 

' -----[ Pins/Constants/Variables ]-------------------------------------------
SDA            var      portb.1                  'transceives to/from SDA
SCL            var      portb.4                  'sends clock pulses

WRITE_DATA     CON     $3C  'Used to perform a Write operation
READ_DATA      CON     $3D  'Used to perform a Read operation

MODE           CON     $02  'Read/Write Register, Selects the operating mode. Default = Single measurement
                             'Send $3C $02 $00 on power up to change to continuous measurement mode.
X_MSB          CON     $03  'Read Register, Output of X MSB 8-bit value.
X_LSB          CON     $04  'Read Register, Output of X LSB 8-bit value.
Z_MSB          CON     $05  'Read Register, Output of Z MSB 8-bit value.
Z_LSB          CON     $06  'Read Register, Output of Z LSB 8-bit value.
Y_MSB          CON     $07  'Read Register, Output of Y MSB 8-bit value.
Y_LSB          CON     $08  'Read Register, Output of Y LSB 8-bit value.
Cont_Mode      CON     $0
SCALEFACTOR    CON     4081 'SCALEFACTOR = 65536 * (255/4095) = 4081
SCALEOFFSET    CON     2048 'The output range of the HMC5883L is -2048 to 2047; therefore to get a 0 (LOWRANGE)to 4095 range
                            'to 4095 (HIGHRANGE) range 2048 must be added to the sensor value.
ATNFACTOR      CON     127  'the ATN function input range is -127 TO 127. In order to get the positive scaled range of
                            '0 to 255 into the range of -127 to 127, 127 must be subtracted.
LOWRANGE       CON     0    'see SCALEOFFSET
HIGHRANGE      CON     4095 'see SCALEOFFSET

X              VAR      byte 'x sensor measured value
Y              VAR      byte 'y sensor measured value
Z              VAR      byte 'z sensor measured value
READX         VAR      WORD 
READY         VAR      WORD
READZ         VAR      WORD

brads          VAR      Word 'angle in brads
degr           VAR      Word 'angle in degrees
azimuth        VAR      Word 'value calculated using X ATN -Y


' -----[ Main Routine ]-------------------------------------------------------

PAUSE 500                                     ' Give sensor needed power up time

  I2CWRITE SDA,SCL,WRITE_DATA,MODE,[Cont_Mode]  ' Send continuous output command

DO

  GOSUB GetRawReading                       ' Get RAW Compass reading

  'RAW X,Y,Z data...
  

        Lcdout $fe, 1 ' Clear LCD screen
        Lcdout "X=",SDEC X  ,"   Y=",SDEC Y 
        Lcdout $fe, $C0, "Z=",SDEC Z
        
        
  'DEBUG HOME, "RAW X,Y,Z", CR
  'DEBUG       "X = ",11, SDEC x, CR
  'DEBUG       "Y = ",11, SDEC y, CR
  'DEBUG       "Z = ",11, SDEC z, CR         ' Print angle
  'DEBUG CR

  'Calculate Azimuth

  GOSUB GetAzimuth

  'Calculated Heading in Degrees

  brads = azimuth     'get angle
  degr = brads */ 361 'convert to degrees
  
  'DEBUG CR
  'DEBUG "Heading in NORTH, EAST, SOUTH, and WEST clockwise from NORTH:", CLREOL, CR, CR
  'DEBUG "Degree " ,11, SDEC degr, CR 'display degrees
  GOSUB GetHeading

LOOP


' -----[ Subroutines ]--------------------------------------------------------

GetRawReading:                                 'Compass module subroutine


    PAUSE 400                                  'Wait for new data to become available


    I2CREAD SDA,SCL,READ_DATA, X_MSB,[X.HIGHBYTE]  'Read the data starting at x_msb 3


    I2CREAD SDA,SCL,READ_DATA ,X_LSB,[X.lowBYTE]

'Do the same for Z and Y:

    I2CREAD SDA,SCL,READ_DATA, Z_MSB,[Z.HIGHBYTE]


    I2CREAD SDA,SCL,READ_DATA ,Z_LSB,[Z.lowBYTE]



    I2CREAD SDA,SCL,READ_DATA, Y_MSB,[Y.HIGHBYTE]


    I2CREAD SDA,SCL,READ_DATA ,Y_LSB,[Y.lowBYTE]

RETURN

GetAzimuth:
'The output range of the HMC5883L is -2048 to 2047 and the input range of the ATN function
'is -127 to 127.  I used the method to scale the output to the input discribed in Parallax's Smart
'Sensors Student Guide v1 starting on page 76.
'SCALEFACTOR = 65536 * (255/4095) = 4081
'SCALEOFFSET = 2048
'ATNFACTOR = 127
'LOWRANGE = 0
'HIGRANGE = 4095 (2048 + 2047 = 4095)

    'x = x + SCALEOFFSET
    'x = (x MIN LOWRANGE MAX HIGHRANGE) ** SCALEFACTOR - ATNFACTOR

    'y = y + SCALEOFFSET
    'y = (y MIN LOWRANGE MAX HIGHRANGE) ** SCALEFACTOR - ATNFACTOR
    
x = readx >>4  
Y = readY >>4
'Z = readZ >>4

  'DEBUG       "SCALED X,Y", CR
  'DEBUG       "X = ",11, SDEC x, CR
  'DEBUG       "Y = ",11, SDEC y, CR

    azimuth = x ATN -y
    


  'DEBUG "Azimuth ",11, SDEC azimuth, CR ' display scaled azimuth
  'DEBUG "COS Azimuth ",11, SDEC COS azimuth, CR ' display scaled cos azimuth
RETURN

GetHeading:
'Gives a heading in North, South, East and West.

    IF degr = 90 THEN
        'DEBUG "NORTH"
        'DEBUG CLREOL
    ENDIF


    IF degr = 0 THEN
         'DEBUG "EAST"
         'DEBUG CLREOL
    ENDIF


    IF degr = 270 THEN
         'DEBUG "SOUTH"
         'DEBUG CLREOL
    ENDIF


    IF degr = 180 THEN
         'DEBUG "WEST"
         'DEBUG CLREOL
    ENDIF

RETURN
Excuse my issues I am still learning....

BR
Andy