MPPT solar battery charger

[theFob]

Thanks iw,
I suppose the first chart explains your code. I found it in the net. But i'm still out of focus.
Why is the measurement of dV? As is shown on the simulation, the voltage of the panel
is almost constant up to 90% of available current. So there is "constant voltage" and "constant current" methods. The voltage remain the same even at night, of course with almost no load. The photons flow become electrons flow, i.e. available current. So the panel is kind of current generator.
And of course, measured dV will be small and inaccurate, may be the noise is from there.
I used hardware circuit similar as algorithm in second chart. So i'm interested of your work. I will try to find my circuits, but unfortunately they are on almost dead HDD ...

Regards

[theFob]

ok, i answered myself. I did simulation again.
The voltage have little change indeed and can be used to determine the direction of duty. But this can be done without this too.
Iw, if i find some time i will make Proteus simulation with your code.
Will be nice to check some other algorithms before the fire of soldering iron



PS I don't know how to resize the images, sorry

[iw2fvo]

Thanks theFob,
I am interested in seeing the simulation of my program when you have time .
The mpp_tracking code I am using works well . My program allow to find out the MPP manually using the potentiometer. It also allows to scan the duty cycle to search the MPP : this is automatic.
The normal mode of the program continuously tracks the MPP. There is a very minor difference among them.
Thanks again,
regards,
Ambrogio
IW2FVO
North Italy

[theFob]

Hi iw,
I'll be glad to do this Had no such fun from long time.
I need the nominal voltage and maximum current values of the panel or just the model.
I noticed the lack of general decoupling diode in your circuit. Is needed for reverse current protection. May be the panel have such internally.
Also a small input filter will be good idea, because the input current of the buck is trapezoidal and is very stressful for the panel.
So the preferred converters are boost (when is possible) or sepic. The input currents there are triangle in continuous mode.
I allowed myself to check your CQ on the net. How far you've come with SG3525 inverter ? I guess it will work with this converter .... ?

Regards

[iw2fvo]

TheFob:
panel data are:
max power 50 w
open circuit volt: 21.6 Vdc
short circuit current : 3.04 A
Max pp volt: 17.6 Vdc
Max pp current : 2.84 A
There is a reverse protection diode ( see D1 on buck converter schematics ).
There is 220 uF at the buck input . Could it be too small ?
The panel keeps the SLA battery charged and so I do not have any inverter to produce line alternate power. I just need 12 VDC nominal.
CQ: >> I have a fully working homemade SDR rx tx for the HF. I have to re_install the antenna that went out completely during the last windy thunderstorm.
I plan to do that at the beginning of the next month.
Thanks.
73, IW2FVO.
Ambrogio

[theFob]

No, you have no panel protection diode. there must be a diode right after the panel, before the point C. It is essential.
If the sun goes down and you have no load at the moment, the input capacitor will return current which can destroy the junctions in the panel.
Diode D1 protect only the buck from the battery. Also the input capacitor is good to be bigger. At least 2200uF in my opinion.
Plus ~1uH inductance after the diode - will help a lot against noise. Few turns on the fly.
SDR sounds interesting, it is something new for me.

[iw2fvo]

Thanks.
I have learn now the need for a panel diode. I will move D1 to the panel input. I will also install a 2200 uF low ESR at panel input and after the diode.
The RF choke is a good idea too.
Ambrogio