Question: PICs with two configuration words versus one, e.g., 16F88 versus 12F683

[tracecom]

Please show me how to organize the configuration bits for PICs with more than one configuration word in the same format that they can be organized for PICs with a single configuration word. There are two code samples: one is for a 12F683 and the configuration bits are organized the way I like to see them; the second is for a 16F88 and the configuration bits are in a long string, but I would like to know how to organize them like they are organized in the 12F683 file. Thanks

' Name: 16F88 Blink1.pbp
' Compiler: PICBASIC PRO Compiler 3
' Assembler: MPASM
' Author: 
' Target PIC: 16F88
' Hardware: CRH Breadboard
' Oscillator: 4MHz Internal
' Date: 10 Dec 2013
' Description:

'Device Configuration
#IF __PROCESSOR__ = "16F88"
#config
 __CONFIG    _CONFIG1, _CP_OFF & _CCP1_RB0 & _DEBUG_OFF & _WRT_PROTECT_OFF & _CPD_OFF & _LVP_OFF & _BODEN_OFF & _MCLR_OFF & _PWRTE_ON & _WDT_OFF & _INTRC_IO
 __CONFIG    _CONFIG2, _IESO_OFF & _FCMEN_OFF
#ENDCONFIG
#else
#MSG "Wrong microcontroller selected!"
#endif

'Register Initialization
TRISB = %11111110          ' Sets up RB0 pin of PORTB as an output
                        ' and pins RB7-RB1 of PORTB as inputs
OSCCON = $60            ' Sets the internal oscillator in the
                        ' 16F88 to 4 MHz                       

'Main Code
start:              ' Label for beginning loop
     PORTB.0 = 1        ' Makes pin PORTB.0,(RB0), output HIGH (+5 volts)
    Pause 500        ' Pause 500 milliseconds (0.5 seconds) with LED on
    PORTB.0 = 0        ' Makes pin PORTB.0,(RB0), output LOW (0 volts)
    Pause 500        ' Pause 500 milliseconds (0.5 seconds) with LED off
    GoTo start        ' Jump to loop label
                    ' Makes the program run forever.
    
    End                ' This line is in case the 
                    ' the program gets lost.

' Name: 12F683 HPWM.pbp
' Compiler: PICBASIC PRO Compiler 3
' Assembler: MPASM
' Author:
' Target PIC: 12F683
' Hardware: CRH Breadboard
' Oscillator: 8MHz Internal
' Date: 1 Nov 2013
' Description: 

' Device Configuration:
#IF __PROCESSOR__ = "12F683"
#config
cfg1 = _INTRC_OSC_NOCLKOUT  ; Internal oscillator
cfg1&= _WDT_OFF             ; Watch Dog Timer disabled
cfg1&= _PWRTE_ON            ; Power-up Timer enabled
cfg1&= _MCLRE_OFF           ; Master Clear Reset disabled
cfg1&= _CP_OFF              ; Program Code Protection disabled
cfg1&= _CPD_OFF             ; Data Code Protection is disabled
cfg1&= _BOD_OFF             ; Brown-out Detect disabled
cfg1&= _IESO_OFF            ; Internal External Switchover mode disabled
cfg1&= _FCMEN_OFF           ; Fail-safe Clock Monitor disabled
 __CONFIG  cfg1             ; Set the configuration bits 
#ENDCONFIG
#else
#MSG "Wrong microcontroller selected!"
#endif

' Register Initializations:
ADCON0  = 0
ANSEL   = 0
CMCON0  = 7           ' Comparators off.
TRISIO  = 0
GPIO    = 0
OSCCON  = %01110001   ' Internal 8MHz osc.
CCP1CON = %00001100   ' CCP1, PWM mode
CCPR1L  = 0
T2CON   = %00000101   ' TMR2 on, prescaler 1:4
PR2     = 250         ' Set the PWM period.

' Includes:

' Defines:
DEFINE OSC 8

' Constants:

' Variables:

' Aliases and modifiers:
Speed var CCPR1L
Btn Var GPIO.4  ' Assuming ; the pin is pulled down to GND by 10K resistor, and button pulls it high to Vdd.
' LED is connected to GPIO.2 (on board PWM module)

' Program Code:
pause 10

Start:
    if btn then 
        if speed + 51 < 256 then    ' 0, 51, 102, 153, 204, 255 0 
            speed = speed + 51
        else
            speed = 0
        endif
        while btn : pause 20 : wend
    endif
    pause 2
goto Start
end

[Dave]

Tracecom, Either way is acceptable, There are 2 configuration words for the F88 processor. There are even more for some of the higher end processors. I don't understand the question?

[tracecom]

Tracecom, Either way is acceptable, There are 2 configuration words for the F88 processor. There are even more for some of the higher end processors. I don't understand the question?

Thanks for the response. I know that both ways work, but I want to use the same style layout for the 16F88 as for the 12F683. I have tried several times to rearrange the 16F88 configuration in a vertical list instead of a long horizontal string, but can't get it to compile.

[Darrel Taylor]

#CONFIG
cfg1 = _INTRC_IO               ; Internal Oscillator
cfg1&= _CP_OFF                 ; Code protection OFF
cfg1&= _CCP1_RB0               ; CCP1 function on RB0
cfg1&= _DEBUG_OFF              ; In-Circuit Debugger Disabled
cfg1&= _WRT_PROTECT_OFF        ; Flash Program Memory Write Enable bits
cfg1&= _CPD_OFF                ; Data EE Memory Code Protection Disabled
cfg1&= _LVP_OFF                ; Low Voltage Programming Disabled
cfg1&= _BODEN_OFF              ; Brown-out Reset Enable bit
cfg1&= _MCLR_OFF               ; Master Clear Reset Disabled
cfg1&= _PWRTE_ON               ; Power-up Timer Enabled
cfg1&= _WDT_OFF                ; Watch-Dog Timer Disabled
   __CONFIG    _CONFIG1, cfg1  ; -- Set config word 1

cfg2 = _IESO_OFF               ; Internal External Switchover Disabled
cfg2&= _FCMEN_OFF              ; Fail-Safe Clock Monitor Disabled
   __CONFIG    _CONFIG2, cfg2  ; -- Set config word 2 
#ENDCONFIG

[tracecom]

Thank you, Darrel.