PIC12F629 flash led

[pmafer]

Hello all.

I'm seeking help to put a simple led flashing on 12F629.

I've try all kinds of configs and get always same result... nothing blinks.

Anybody knows id 629 have any particularity thah i don't see?

i'm using internal 4 mhz osc and 1k resistor on mclr and picall programmer.

led on gpio.0

Can anyone give some ideias?

ps. i've read datasheet and manual...

thanks
Paul

[HenrikOlsson]

Hi,
Post your code, complete with the CONFIG-settings you're using.

/Henrik.

[AvionicsMaster1]

Probably oughta add a schematic also.

[pmafer]

Hello again.
tks for your aswers!

code follows:

Define OSCCAL_1K 1
DEFINE OSC 4

CMCON = 7
OPTION_REG.7= 0
GPIO = %00000000
TRISIO = %00000001


Start:

HIGH GPIO.0
PAUSE 1000
LOW GPIO.0
PAUSE 1000

GOTO Start
END

Hi,
Post your code, complete with the CONFIG-settings you're using.

/Henrik.

[Demon]

Shouldn't DEFINE be uppercase?

Robert

[Aussie Barry]

You have set GPIO.0 as an input with your TRISIO = %00000001 statement.

Try using TRISIO = 0 instead and see how it goes.

Also, I am not sure of your purpose for the OSCCAL statement. IMO, it shouldn't be necessary for such a simple LED flash program.

Cheers
Barry
VK2XBP

[longpole001]

dont know if you fixed the input to an output as barry suggested but i think that the problem

you can remove the pullup option as they are turn off anyway if outputs
the calibration setting in osccal seems to be cleared during an erase on this chip
so setting the register if you need to it adjust may be needed , but other wise id not worry if it just blink a led
i would also recommend a more up to date IC such as 12F683 as the new designed chips have very similar instruction / register setups which make it easy to go to other new chips when learning a PIC

hope it helps

Cheers

Sheldon

#CONFIG
  __config _INTRC_OSC_NOCLKOUT & _WDT_OFF & _PWRTE_ON & _MCLRE_OFF & _CP_OFF 
 
#ENDCONFIG

OSCCAL = %100000                ' 4MhZ - Set calibration register to Center Freq - Note Erasing the device also clears the calibration value for internal osc

CMCON        = 0               ' Comparators not used 
TRISIO        = %00000000       ' set all GPIO as outputs  - Note Master clear pin GPIO is not used 
OPTION_REG.7 = 0                 ' Set Week Pullups globle off    . Note when GPIO  SET AS output Week pullups  is automaticly turned off 


DEFINE OSC 4            ' Timing reference for pause , pauseus commands 

Start:

toggle GPIO.0
pause 1000         ' pause of 1sec 

goto Start

End

[HenrikOlsson]

Hi,

I don't see any real issues with the original code which would prevent it from working.

Yes, the TRIS-setting is indeed backwards and setting it correctly is always good practice but HIGH/LOW takes care of it for you so it shouldn't be a showstopper in this particular case.

The situation with define/DEFINE/DefINe/defiNE has been covered many times by now. The actual keyword (DEFINE) is NOT case sensitive, what comes after the keyword IS and that looks alright to me although the OSCCAL shouldn't be needed AFAIK. So, not a problem with that either. Comparator (which has a Connection on GPIO.0) is turned off correctly so not an issue with that either. I can't see any real problem.

My vote is on a hardware issue, perhaps your programmer doesn't release MCLR after programming - if you keep it attached that is.

Which version of PBP are you using?

/Henrik.

[AvionicsMaster1]

I have been schooled by the wizard and Henrik is correct on deFINE.

I agree OSSCAL is unneccessary but you do need to set the ports to digital with the ANSEL = 0. You really don't need the OPTION_REG statement for just a simple program. TRISIO should just read TRISIO = 0 to set all pins, except GPIO.3 (pin 4), as outputs. HIGH/LOW will do that but it looks cleaner setting it in the TRISIO. At least IMHO.

DEFINE OSC 4
ANSEL=0
CMCON = 7
OPTION_REG.7= 0
GPIO = 0
TRISIO = 0
Start:

HIGH GPIO.0
PAUSE 1000
LOW GPIO.0
PAUSE 1000

GOTO Start
END

I would also submit you need a 300ish ohm resistor in series with the LED and not much higher. If you lack the resistor you can hook it directly up to the PIC as the PIC will protect itself and only source about 20ish mA. I don't remember exactly what the PIC will source or sink but you can find it in the datasheet. GPIO.0 is pin 7 on the 12F629 and should have the unmarked(Anode) end of the LED hooked to it with the marked end (Cathode) to ground/common/return or whatever you want to call it.

Make sure pin 4 MCLR is tied to the voltage source, +5 VDC, with a 10kish resistor. If you're not hooked to +5VDC then you'll have to adjust the size of the resistor in series with the LED.

It should work.

[HenrikOlsson]

Hi,
The 12F629 doesn't have an ADC, there is no ANSEL register available.

Since my last post I've breadboarded a 12F629 and tried Pauls code as posted, it works just fine. So I'm still leaning towards a hardware issue.

/Henrik.

[pmafer]

Hello,

Thanks all for your comments.

i recheck hardware and all seems ok.

i'm going crazy with this one. defective ic? its uncommon...

Henrik: can post hex to see if any diference? do you use default settings file?

thanks again,
Paul