Sine wave power inverter

[mat janssen]

Hallo Rishi. Can you post the schema and the code for this? All of us will learn about this subject!

[Navneet Vinaik]

Dear Mincing,

Thanks for your reply, and sorry for the delay.

I want to understand the technicalities involved in designing systems on ferrites. To be precise, what would be the kind of drive systems, snubbers, clamps and most important transformer design in case of ferrite based systems.
I would be grateful if you could provide me some details etc.

Regards

Navneet Vinaik

[mincing]

Dear Mincing,

Thanks for your reply, and sorry for the delay.

I want to understand the technicalities involved in designing systems on ferrites. To be precise, what would be the kind of drive systems, snubbers, clamps and most important transformer design in case of ferrite based systems.
I would be grateful if you could provide me some details etc.

Regards

Navneet Vinaik

could you Pl. give me your mail ID ,I will forward some documents!

[Navneet Vinaik]

Dear Mincing,

Thanks a lot for your helping hand...
My email ID is [email protected]; [email protected]

I am pretty confident that I can build a good quality HF inverter, presently busy in getting all the tools ready...I have an old oscilloscope which has served us for the past 45 years but for this technology I am arranging resources to get a DSO among others tools.
Please send me whatever help that you can, I would be grateful to you as it will help be do my homework before I get into the battlefield!!!

[Rishi]

Hallo Rishi. Can you post the schema and the code for this? All of us will learn about this subject!

hello mat

Yes i will send u details but it will take some time.

i have design 12v/24v dc to 350v dc converter with analog ic sg3525 and already
achieve effeciency more then 90%.

[sougata]

Hi everybody,

I have been greatly helped by this site http://schmidt-walter.fbe.fh-darmsta..._e/smps_e.html . It is the english version of the original german site by the author. Great work, great javascript based smps calculator.

I hope things become easier right now.

Regular bread and butter (hard to earn in my city ) jobs leave me almost no time to work on this project. But seeing this thread still kicking does give me some inspiration.

Thanks to everybody who contributed to this thread.

[BrianT]

Take a look at Don Lancaster's site at www.tinaja.com. Search for MAGIC SINEWAVES and you will find information on how to build very low harmonic sinewaves.

HTH

Brian

[mincing]

Hi friends,

I have difficulty in seeing the bridge driven through with sinePWM.

I have built everything but the bridge is getting shorted when I try to run the inverter.

Any Ideas how to achieve dead time control in Software.

Sougata are you active?

[sougata]

Hi,

I am hardly getting time to get into the forum and I know I am missing something or the other.

Mincing,

Try to use a resistive load at the output of the bridge and inspect the i/o signals with a scope. Sometimes improver gate drive and/or switch off spike can kill MOSFETs. Please post the schematic and code snippets I will try to help if it is within my scope/knowledge. I am not as active now but you can count on every other member on this forum. Far far better than me.

If you find that you cannot reveal the code/schematic due to commercial problems you can pm me. Again I would try, no commitments.

[mincing]

Thanks for the reply!

I understood that the current drawn(peak current ) is actually higher than what is seen on front panel meter of the Power supply I used.

Do you have any calc. for peak currents that flow in to the bridge?

Actual current or Dc current is only about 1.5 to 2Amps but peak is over 5Amps. at about 15 to 20 V on no load with a transformer connected.



Also what happened to your Double conversion Inverter. I have some documents ,I like to forward to you on the subject.
I am not sure if I can post them here, give me your mail ID I 'll forward the same.

Any one who wants to build HF inverter.

Thanks again!

[mincing]

Hi sougata,

Hope everything is fine !

I have difficulty in reading the feed back and adjusting the PWM.
Presently I am reading a DC proportional to the output voltage.PWM is continuously adjusted and checked with the feed back.
However the moment ckt enter the closed loop out put becomes unstable.It keeps changing continuously.

Could you please throw some light on this./

Thanks,