Wireless modules - help with code not working

[Demon]

You pause 500 after transmit, but pause 1000 after reception?

Robert

[Ioannis]

Besides what Robert noted, you have to setup port A.3 as high before transmitting. RS232 needs a standard state before tx/rx.

So, I suppose T9600 made the difference?

Include "modedefs.bas" 
DEFINE OSC 10

high porta.3
TRISA = %00000000

CMCON=7

pause 2000

TEST:
    serout PortA.3, T9600,["SSSSSSSBOB"] 
    PAUSE 500
    GOTO TEST  
END

Ioannis

[Dick Ivers]

Hi all, I'm trying the true mode, but my loopback setup is still not working.

'**************************************************************************
'*Program to test XRF radio communications via loopback method            *
'*Uses a pushbutton switch on porta pin 4                                 *
'*Target processor is PIC 12f1822                                         *
'*207 program words, revised 05/07/2013                                   *
'*Program by Dick Ivers                                                   *
'*All rights reserved                                                     *
'************************************************************************** 
'set 12f1822 configurat1on
#CONFIG
  __config _CONFIG1, _FOSC_INTOSC & _MCLRE_OFF & _CLKOUTEN_OFF & _WDTE_ON
  __config _CONFIG2, _PLLEN_OFF & _LVP_OFF
#endconfig

'set registers
        OSCCON = %01111000   '16 mhz osc
        OSCTUNE = 0          'factory calibration
        ANSELA = 0           'all digital inputs
        OPTION_REG.7 = 0     'global pullups enabled
        WPUA = %010000       'porta pin 4 weak pullup enabled
        CM1CON0.7 = 0        'comparator disabled
        TRISA  = %011110     'porta.0 & porta.5 are outputs, all others input

    while OSCSTAT.0 = 0      'wait for stable freq.
    wend
    
    define OSC 16            '16 mhz oscillator

'Define debug parameters
DEFINE DEBUG_REGG PORTA        'set debug port to porta
DEFINE DEBUG_BIT 0             'use pin ra0 of porta for debug
DEFINE DEBUG_BAUD 9600         'set baud rate to 9600
DEFINE DEBUG_MODE 0            'communicate in true mode

DEFINE DEBUGIN_REGG PORTA      'set debug port to porta
DEFINE DEBUGIN_BIT 1           'use pin ra1 of porta for debugin
DEFINE DEBUGIN_BAUD 9600       'set baud rate to 9600
DEFINE DEBUGIN_MODE 0          'communicate in true mode

    i var byte
    char var byte

    For i = 1 to 3
    porta.5 = 0              'led on
    pause 333
    porta.5 = 1              'led off
    pause 333
    next

asleep:
    nap 2   'delay 4 ms
    if porta.4 = 1 then asleep
  
DT:
    debug 55
    debugin 100,blink,[char]
    if char = 55 then
     porta.5 = 0            'led on solid
     goto halt
    endif    

blink:
    porta.5 = 0     'led
    pause 500
    porta.5 = 1     'led off
    pause 500
    if porta.4 =1 then asleep
    goto DT   
   
halt:
    stop                   'led stays on

The communications not working. The led blinks when the remote transceiver is not powered, as it should. When its powered the program should branch to a solid on led , but no it keeps blinking. Any ideas?

[Ioannis]

Dick, I would suggest at first to test your code with a PC and see if you have the PIC working. For this you will need a MAX232 or similar to invert and drive the serial port.

If this test passes please post your results. But I have a feeling that it won't.

Ioannis

P.S. Also try with capitals in define OSC 16. As this: DEFINE OSC 16. Just in case...

[Dick Ivers]

Ioannis,
PIC to PC is working. Code and setup as follows:

'**************************************************************************
'*Program to test PIC to PC communications via loopback method            *
'*Target processor is PIC 12f1822                                         *
'*142 program words, revised 05/08/2013                                   *
'*Program by Dick Ivers                                                   *
'*All rights reserved                                                     *
'************************************************************************** 
'set 12f1822 configurat1on
#CONFIG
  __config _CONFIG1, _FOSC_INTOSC & _MCLRE_OFF & _CLKOUTEN_OFF & _WDTE_ON
  __config _CONFIG2, _PLLEN_OFF & _LVP_OFF
#endconfig

'set registers
        OSCCON = %01111000   '16 mhz osc
        OSCTUNE = 0          'factory calibration
        ANSELA = 0           'all digital inputs
        OPTION_REG.7 = 0     'global pullups enabled
        WPUA = %010010       'porta pin 1 and pin 4 weak pullups enabled
        CM1CON0.7 = 0        'comparator disabled
        TRISA  = %011110     'porta.0 & porta.5 are outputs, all others input

    while OSCSTAT.0 = 0      'wait for stable freq.
    wend
    
    define OSC 16            '16 mhz oscillator

'Define debug parameters 
DEFINE DEBUG_REGG PORTA        'set debug port to porta
DEFINE DEBUG_BIT 0             'use pin ra0 of porta for debug
DEFINE DEBUG_BAUD 9600         'set baud rate to 9600
DEFINE DEBUG_MODE 1            'communicate in inverted mode

DEFINE DEBUGIN_REGG PORTA      'set debug port to porta
DEFINE DEBUGIN_BIT 1           'use pin ra1 of porta for debugin
DEFINE DEBUGIN_BAUD 9600       'set baud rate to 9600
DEFINE DEBUGIN_MODE 1          'communicate in inverted mode

    i var byte
    char var byte

    For i = 1 to 3
    porta.5 = 0              'led on
    pause 333
    porta.5 = 1              'led off
    pause 333
    next

'user input with VT100 terminal

re:     debugin [char]     
        debug char
        
        goto re

The PIC echos back to the PC correctly. Double characters display as expected. Note that the transmission mode is inverted. I believe this mode is standard for RS232 communications. Also, I am using a null modem cable (Tx and Rx reversed ). I believe this is also standard. Haven't tried the radio link yet with this set up.. Any suggestions?
Dick

p.s. The DEFINES are capitals in the actual code. Not all show this way with the pasted code.

[Demon]

I'd type over the DEFINES in capitals. If you copy & paste from your code and they come out in lower case here, then it seems like your IDE is just displaying to you in upper case. They are still lower as far as PBP is concerned.

Robert

[Ioannis]

Since PIC to PC is working then I have three thoughts on this.

1. one or both modules are not working. You may try here to change the modules between them.

2. Settings are not the defaults

3. The feeds to the modules are reversed (tx to rx etc).

The modules need true mode and not the inverse you just tested with the PC. But I suppose you will change your code for this test.

Wish you luck, cannot see anything else now...

Ioannis