MCSX not fully loading, anyone else?


Closed Thread
Results 1 to 6 of 6

Hybrid View

  1. #1
    Join Date
    Feb 2008
    Location
    Michigan, USA
    Posts
    231


    Did you find this post helpful? Yes | No

    Default Re: MCSX not fully loading, anyone else?

    I see that a number of you have looked at this and there are no ideas as of yet.
    I am beginning to believe it is more of a machine problem than a program problem. I have down loaded a new copy from Mechanique and loaded it with the same symptoms. If I boot in safe mode, it still will not run, and if I open the task manager, PBPX.exe locks up 50% of my core 2 Duo processor until i kill it even after closing an unresponsive program. I have once seen an error that stated ; WSAStartup not yet determined, but I have not been able to go any further.
    Still fishing for suggestions, short of rebuilding my system.
    Thanks.
    Bo

  2. #2
    Join Date
    Feb 2008
    Location
    Michigan, USA
    Posts
    231


    Did you find this post helpful? Yes | No

    Default Re: MCSX not fully loading, anyone else?

    BTW, MCS v3 still runs fine. it just makes it hard to work with PBP3 without MCS v5.

  3. #3
    Join Date
    Feb 2010
    Location
    USA, New England
    Posts
    164


    Did you find this post helpful? Yes | No

    Default Re: MCSX not fully loading, anyone else?

    I've no particular insight for you, but I can confirm I'm running it on a very similar system without issues.

    System properties says:
    Intel(R) Core(TM)2 Duo CPU
    P9600 @ 2.66GHz

    I assume you've tried a clean install of MCSPX?

    Best Regards,
    Paul
    The way to avoid mistakes is to gain experience. The way to gain experience is to make mistakes.

  4. #4
    Join Date
    Mar 2003
    Location
    Commerce Michigan USA
    Posts
    1,166


    Did you find this post helpful? Yes | No

    Default Re: MCSX not fully loading, anyone else?

    Try a search on the web for "ThunkConnect32". From what I have read it's a corrupt windows problem and there are some automated fixes available for it.
    Dave Purola,
    N8NTA
    EN82fn

  5. #5
    Join Date
    Feb 2008
    Location
    Michigan, USA
    Posts
    231


    Did you find this post helpful? Yes | No

    Default Re: MCSX not fully loading, anyone else?

    Thanks for the replys. I have found that there are corrections for the ThunkConnect32 problem and will work on them, but I have been running with that error for years and Jeff S has told me in the past that it was not a problem. If it does correct anything, I will post it here.

Similar Threads

  1. loading data to EXt. eeprom
    By MINHLE in forum General
    Replies: 0
    Last Post: - 28th December 2009, 17:56
  2. 16F628 and LMX2306 PLL loading.. help
    By kessral in forum mel PIC BASIC Pro
    Replies: 13
    Last Post: - 11th June 2008, 17:03
  3. Loading EEPROM
    By Dick Ivers in forum mel PIC BASIC Pro
    Replies: 6
    Last Post: - 25th August 2005, 03:44
  4. Loading Arrays
    By CocaColaKid in forum mel PIC BASIC Pro
    Replies: 1
    Last Post: - 8th August 2005, 21:40
  5. pre loading eeprom data
    By Rob Martin in forum mel PIC BASIC Pro
    Replies: 3
    Last Post: - 17th April 2004, 11:18

Members who have read this thread : 0

You do not have permission to view the list of names.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts