How to post Code

[Terry]

Quick question, how do I post code within the window on the forum, I have looked on the the site, but I can't find it, I am sure it is very simple to do.

Thanks,
Terry

[Darrel Taylor]

At the bottom of each thread, there is a "Posting Permissions" box.
In there you'll see a "BB code" link.

That page shows all the different things you can do in a post on the forum.
The one you want is "Code".

HTH,

[mackrackit]

Once you click on the reply button you will want to click on the Go Advanced button.
Then you should see a tool bar above the editor box. The "#" will give you the code tags.
You will also want to click the upper left button of the tool bar to go into source mode, it works better than WYSIWYG.

[Demon]

Good place to see if my code posts properly. I've seen some have problems with %.

'****************************************************************
'*  Name    : LAB X1 16F877 Timer Interrupt.BAS                 *
'*  Author  : Demon                                      *
'*  Notice  : Copyright (c) 2012                                *
'*          : All Rights Reserved                               *
'*  Date    : 2012-01-06                                        *
'*  Version : 1.0                                               *
'*  Notes   : PIC Basic Pro v2.60C                              *
'*          : MicroCode Studio Plus v2.2.1.1                    *
'*          : MPASM v3.50                                       *
'*          : Lab X1 Experimental Board                         *
'*          : MeLabs U2 Programmer v4.32                        *
'****************************************************************
'define  LOADER_USED 1

' Comment out CONFIG in MPASM include (File: 16F877.INC in PBP folder).
@ __config _HS_OSC & _WDT_OFF & _PWRTE_ON & _BODEN_ON & _LVP_OFF & _CPD_OFF & _WRT_ENABLE_OFF & _DEBUG_OFF & _PWRTE_OFF

define  OSC 20

DEFINE  LCD_DREG      PORTD         ' Set LCD data port
DEFINE  LCD_DBIT      0             ' Set starting data bit
DEFINE  LCD_RSREG     PORTE         ' Set LCD register select port
DEFINE  LCD_RSBIT     0             ' Set LCD register select bit
DEFINE  LCD_EREG      PORTE         ' Set LCD enable port
DEFINE  LCD_EBIT      1             ' Set LCD enable bit
DEFINE  LCD_BITS      8             ' Set LCD bus size
DEFINE  LCD_LINES     2             ' Set number of lines on LCD
define  LCD_COMMANDUS 2000          ' Set command delay time in microseconds
DEFINE  LCD_DATAUS    50            ' Set data delay time in microseconds

    TRISD = %00000000               ' Set all port D pins to output
    TRISE = %00000000               ' Set all port E pins to output

    ADCON1 = 7                      ' A/D off, all digital

wsave   VAR BYTE    $70 SYSTEM      ' Required by Instant Interrupt routine

    PAUSE   1000                    ' Wait for LCD to initalize
    LCDOUT  $FE,1,"LabX1 16F877 Tim Int"

'---[INT - interrupt includes]--------------------------------------------------
INCLUDE "DT_INTS-14.bas"     ; Base Interrupt System
INCLUDE "ReEnterPBP.bas"     ; Include if using PBP interrupts
INCLUDE "Elapsed_INT.bas"     ; Elapsed Time interrupts

'---[INT - interrupt definition]------------------------------------------------
ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
        INT_Handler   TMR1_INT,  _ClockCount,   PBP,  yes
    endm
    INT_CREATE            ; Creates the interrupt processor
ENDASM

@   INT_ENABLE  TMR1_INT  ; Enable Timer 1 Interrupts  

    GOSUB ResetTime           ' Reset Time to  0d-00:00:00.00
    GOSUB StartTimer          ' Start the Elapsed Timer

Main:
    IF SecondsChanged = 1 THEN  
        SecondsChanged = 0
        LCDOUT $FE,$C0, DEC Days,"d-",DEC2 Hours,":",DEC2 Minutes,":",DEC2 Seconds
    ENDIF
    GOTO Main

    end

WOOT! It worked!

Robert