SD card library?

[micromaster]

Hi all

i also have been working with sd filing system with number of lang: including pic basic and hi-tec c . all of them worked very well with proteus simulation environment(isis). but all of them were very unstable when i build them in practical world. Can anyone give me some tips to make them stably working?? ive used home made p.c.bs for my systems. Are there any specific potential dividing resisters to be used at port outputs and sd card input? ive been using 1k + 10k combination.any caps mabe?? im using pic 18f 2550 for all of my sd card based systems.

[pedja089]

How much current sd card is draw when writing file?

[mackrackit]

Run the whole system at 3.3 volts and then you will not have to use dividing resistors.

[pedja089]

I meant on power supply pin.
I'm waiting for test pcb to arrive from manufacturer....

[micromaster]

Run the whole system at 3.3 volts and then you will not have to use dividing resistors.

Thanks, but will pic 18f2550 can run on 3.3v? because its hard to find any other lo power versions in our electronic shops.

thanks.

[mackrackit]

Yes, the 2550 and 4550 will run on 3.3 volt. See the link in post #4.

Use a 4MHz external OSC and the chip can be PLL'ed to 48 MHz if needed. The electrical section of the data sheet shows what can be done.

[Charlie]

I've been playing with this code for a couple days now with no joy. My biggest question revolves around my SD card. I have several. They ALL have 9 pins. As does the socket on my development board. Yet the code seems to be written for an SD card with 12 pins? I have no "Write Protect" or "card detect" lines, nor can I find reference to them anywhere but on this site. Do I fake the pins? High or low?
To further add to the confusion, I'm using an 18F2550 and I need the hardware serial port. Since a pin is shared with the hardware SPI port, I'm trying to use SHIFTOUT / SHIFTIN. Things seem to be getting to the SD card, but it does not reply (I get 0's).
Am I missing something simple? Response from an INIT is 6...

[Alexey]

Hi Charlie,

I use PIC18F25K22

and do it this way:

'--------------SD CARD----------------------

'SD_DO VAR PORTC.0
' Alias PIC pins and registers for SD/MMC cardYTE
SDI VAR PORTC.0 ' SPI data in SD #7 (SD_DO)
SDI_TRIS VAR TRISC.0 ' SPI data in direction
SCL VAR PORTC.1 ' SPI clock SD #5
SCL_TRIS VAR TRISC.1 ' SPI clock direction
SDO VAR PORTC.2 ' SPI data out uSD #3
SDO_TRIS VAR TRISC.2 ' SPI data out direction
SD_CS VAR PORTC.3 ' SD card chip select uSD #2
SD_CS_TRIS VAR TRISC.3 ' SD card chip select direction

'SD_CD VAR bit: SD_CD = 1 PORTC.0 ' SD card detect
'SD_CD_TRIS VAR TRISC.0 ' SD card detect direction

INCLUDE "SDFS.PBP"
SDC_UseHardSPI = FALSE ' Use hardware SSP port for SPI.

...


all lines in the SDFS.PBP that refer to the card write protection, card inserted and so on things I disabled like this:

' Subroutines for communicating with an SD/MMC card
' Subroutine to initialize SD card pins
InitIO:
SD_CS = 1 ' SD card not selected.
SD_CS_TRIS = 0 ' Output SD card chip select.
''' SD_CD_TRIS = 1 ' Input card detect.
''' SD_WE_TRIS = 1 ' Input write protect.
SDO = 1 ' Start SPI data out high.
SDO_TRIS = 0 ' Output SPI data out.
SDI_TRIS = 1 ' Input SPI data in.
SCL = 1 ' SPI clock idles high.
SCL_TRIS = 0 ' Output SPI clock.
Return




' Subroutine to initialize hardware SSP for SPI at less than 400kHz
OpenSPIM:
If (SDC_UseHardSPI) Then
''' SSPSTAT = 000000 ' Sample at middle of data output time, Mode 1, 1: Transmit on idle to active clock transition.
''' SSPCON1 = 010010 ' SPI master mode, clock = Fosc/64, Mode 1, 1: Clock idle high.
''' SSPEN = 1 ' Enable hardware SPI port.
Endif
Return




' Subroutine to initialize hardware SSP for SPI at full speed
OpenSPIMFast:
If (SDC_UseHardSPI) Then
''' SSPSTAT = 000000 ' Sample at middle of data output time, Mode 1, 1: Transmit on idle to active clock transition.
''' SSPCON1 = 010000 ' SPI master mode, clock = Fosc/64, Mode 1, 1: Clock idle high.
''' SSPEN = 1 ' Enable hardware SPI port.
Endif
Return




I use micro SD card. You might notice the pins used for card interface are shared with ICSP, but the card can not work while the programmer is connected. Programmer probably does not like such neighbor too (one needs pull up and the other has internal pull down, but it works.

I could not attach the file - error happens - "invalid file" I do not know why, but you see the idea - just comment everything you do not use

Best regards,