18F2620 pbp3 example config please

[retepsnikrep]

Thanks for the guidance here is my new 18F2620 config.

'------------------------------ New General 18F2620 configuration --------------------------
'#CONFIG
' __CONFIG _CONFIG1H, _OSC_INTIO67_1H & _FCMEN_OFF_1H & _IESO_OFF_1H
' __CONFIG _CONFIG2L, _PWRT_OFF_2L & _BOREN_OFF_2L
' __CONFIG _CONFIG2H, _WDT_OFF_2H
' __CONFIG _CONFIG3H, _PBADEN_OFF_3H & _LPT1OSC_OFF_3H & _MCLRE_OFF_3H
' __CONFIG _CONFIG4L, _STVREN_OFF_4L & _LVP_OFF_4L & _XINST_OFF_4L & _DEBUG_OFF_4L
'#ENDCONFIG
'DEFINE OSC 8   'Set PicBasic Pro processor speed to 8 Mhz   
'OSCCON = %01110110   'Internal 8 mhz Osc and stable 
'CMCON  = %00000111  'Comparators Off
'T1CON  = %00110000  '$30 = Prescaler 1:8, TMR1 OFF
 
'TRISA = %00001011   'SET PORTA0, A1 & A3 AS INPUTS, REST AS OUTPUTS
'TRISB = %00000000   'SET PORTB AS OUTPUTS
'TRISC = %10010000   'SET PORTC AS OUTPUTS EXCEPT PORT C4 & C7
 
'ADCON0 = %00000001  'SETUP ADC & ENABLE ADC MODULE on AD0
'ADCON1 = %00001110  'SETUP ADC SET REFV to VDD & VSS AN0 
'ADCON2 = %00100010  'SETUP ADC FOSC/32 LEFT JUSTIFY TAD 8

Below is my working old 16F886 config. Any glaring errors in the above? I'm just swapping chips and I want all functions to remain the same.

'------------------------------ General 16F886 configuration --------------------------
#CONFIG
 __CONFIG _CONFIG1, _LVP_OFF & _FCMEN_OFF & _IESO_OFF & _BOR_OFF & _CPD_OFF & _CP_OFF & _MCLRE_OFF & _PWRTE_OFF & _WDT_OFF & 
_INTRC_OSC_NOCLKOUT
 __CONFIG _CONFIG2, _WRT_OFF & _BOR21V
#ENDCONFIG
DEFINE OSC 8   'Set PicBasic Pro processor speed to 8 Mhz   
OSCCON = %01110101   'Internal 8 mhz Osc and stable 
CM1CON0 = 0    'Comparator Off
CM2CON0 = 0    'Comparator Off
T1CON  = %00110000  '$30 = Prescaler 1:8, TMR1 OFF
 
TRISA = %00001011   'SET PORTA0, A1 & A3 AS INPUTS, REST AS OUTPUTS
TRISB = %00000000   'SET PORTB AS OUTPUTS
TRISC = %10010000   'SET PORTC AS OUTPUTS EXCEPT PORT C4 & C7
 
ANSEL  = %00000001  'SET INPUT AN0 AS ANALOG INPUT
ANSELH = %00000000              'Disable PortB AD
 
ADCON0 = %10000001  'SETUP ADC CONVERTER MODULE FOSC/32 & ENABLE ADC MODULE on AD0
ADCON1 = %00000000  'SETUP ADC LEFT JUSTIFY SET REFV to VDD & VSS

Thanks Peter

[retepsnikrep]

I moved to a new pic to gain memory space but the same program compiled for the new pic is nearly twice the size as the 16F886 version :?
Why is that and can I get some memory back. I don't need 18F longs for instance and that is already disabled in the compiler.

[HenrikOlsson]

Hi,
My guess is that it's because on the 16 series (10 & 12 too I believe) the memory is "measured" in WORDS (14-bit words if I'm not mistaken) while on the 18 series it's measured in BYTES. So I don't think your program is actually getting twice as big, it's just displaying the size of it in BYTES instead of in WORDS.

/Henrik.

[retepsnikrep]

I still get the some config bits warning with pickit 2.
I can't see why?

'------------------------------ General 18F2620 configuration --------------------------

#CONFIG
 __CONFIG _CONFIG1H, _OSC_INTIO67_1H & _FCMEN_OFF_1H & _IESO_OFF_1H
 __CONFIG _CONFIG2L, _PWRT_OFF_2L & _BOREN_OFF_2L
 __CONFIG _CONFIG2H, _WDT_ON_2H & _WDTPS_512_2H
 __CONFIG _CONFIG3H, _PBADEN_OFF_3H & _LPT1OSC_OFF_3H & _MCLRE_OFF_3H
 __CONFIG _CONFIG4L, _STVREN_OFF_4L & _LVP_OFF_4L & _XINST_OFF_4L & _DEBUG_OFF_4L
#ENDCONFIG


DEFINE OSC 8			'Set PicBasic Pro processor speed to 8 Mhz 
OSCCON = %01110000 		'Internal 8 mhz Osc  

WDTCON = %00010101		'Set watchdog Timer for 1 second 

CMCON  = %00000111		'Comparators Off
CVRCON = %00000000		'CvRef Powered Down 

CCP1CON= %00001100		'CCP1 Module PWM Mode
CCP2CON= %00000000		'CCP2 Module Disabled 

HLVDCON= %00000000		'HLVCON Disabled

T1CON  = %00110000		'$30 = Prescaler 1:8, TMR1 OFF
	
TRISA = %00001011 		'SET PORTA0, A1 & A3 AS INPUTS, REST AS OUTPUTS
TRISB = %00000000 		'SET PORTB AS OUTPUTS
TRISC = %10010000 		'SET PORTC AS OUTPUTS EXCEPT PORT C4 & C7
	
ADCON0 = %00000001		'SETUP ADC & ENABLE ADC MODULE on AN0
ADCON1 = %00001110		'SETUP ADC SET REFV to VDD & VSS AN0 
ADCON2 = %00100010		'SETUP ADC FOSC/32 LEFT JUSTIFY TAD 8

[HenrikOlsson]

Hi,
What exactly does that mean, what warnings do you get and from where do you get them?

Your code compiles and assembles fine with PBP 3.0.7.4 & MPASM 5.45. Are you using the standalone software for the PICKit2 and is it THAT software that gives you these misterious warnings?

/Henrik.

[Darrel Taylor]

Make a "Complete" set of configs for any chip with ease.

meCONFIG
http://support.melabs.com/content/563-meCONFIG

[retepsnikrep]

Yes the pickit 2 software states when programming that some configuration bits not in acceptable condition. It still programs and works fine but is disconcerting for users.

That new meconfig software is interesting I see quite a few bits/parameters I have ignored/did not know about. :?