Serial port remote problem

[luxornet]

Hi.

I try a small project that send command via PC serial port to a PIC12F625 connected without MAX232. I use some example from Serial Port Expander.
Here I try to light a LED connected on pin GP1 of PIC12F625.
The code is in PBP.
I used Visual Basic 6 to build the windows executable.
I used Proteus 7.2 to made the schematic and simulating the circuit; simulation works fine, I put a virtual terminal on pin 3 of serial port and type „a01” to light the led and „a00” to shut the led.
But in practice my project doesn’t work; I have a signal on GPIO.0 port pin of 12F625 but nothing on GPIO.1.
Do you have any ideea?
Thank you.

Visual Basic

 
 
Option Explicit
 
Private Sub CommandOFF_Click()
    Dim sir As String
    DoEvents
    sir = "a" & "0" & "0"
    MSComm1.Output = sir
    Shape1.FillColor = vbRed
End Sub
 
Private Sub CommandON_Click()
    Dim sir As String
    DoEvents
    sir = "a" & "0" & "1"
    MSComm1.Output = sir
    Shape1.FillColor = vbGreen
End Sub
 
Private Sub Form_Load()
    MSComm1.CommPort = 1
    MSComm1.Settings = "2400,n,8,2"
    MSComm1.InputLen = 0
    MSComm1.RThreshold = 1
    MSComm1.PortOpen = True
    If MSComm1.PortOpen = False Then
        Debug.Print "Port closed"
    Else
        Debug.Print "Port opened"
    End If
End Sub

PICBasic Code

 
' PIC12F675
' Pic Basic Pro Compiler 2.45, (c) 1998, 2004 microEngineering Labs, Inc.
' Assembler used is PM.EXE, provided with microEngineering Labs PICBasic Compiler
'
' This program flashes an LED connected to port GP1.
' ************************************************* ************
' REMOTE RX
' **************************************************************
' Pic Basic Pro Compiler 2.45A1, (c) microEngineering Labs, Inc.
' Assembler used is PM.EXE, provided with microEngineering Labs PICBasic Compiler
 
 
 
 
define OSC 4
INCLUDE "modedefs.bas"
@ DEVICE PIC12F675
    ANSEL   =   000000   'set all pin 0 = Digital I/O;
    ADCON0.7 = 1        ' Right justify result
    CMCON = 7                ' Analog comparators off
@ DEVICE PIC12F675, INTRC_OSC; Use internal oscilator
@ DEVICE PIC12F675, WDT_OFF  ;WATCHDOG
@ DEVICE PIC12F675, PWRT_OFF ;POWER ON TIMER
@ DEVICE PIC12F675, BOD_OFF  ;BROWNOUT RESET
@ DEVICE PIC12F675, MCLR_OFF 
 
 
    trisio = 100001
    INTCON=0               'interrupts off
    CMCON=7                'all digital for low power use
                           'CMCON disables the comparator
    LedNr             var byte
    stat   var byte
   
    LedOut   VAR    GPIO.1  'GP1 Led output
    SerialIn VAR    GPIO.0  'serial input pin
'start
 
' Set Debug pin port
DEFINE DEBUG_REG GPIO
 
' Set Debug pin bit
DEFINE DEBUG_BIT 2
 
' Set Debug baud rate
DEFINE DEBUG_BAUD 2400
 
' Set Debug mode: 0 = true, 1 = inverted
DEFINE DEBUG_MODE 0
DEFINE DEBUG_PACING 1000
debug $0D,$0A
debug "Start! ",$0D,$0A
    ledout = 0 'Shut LED
 
loop1:
'   Wait until the character "a" is received serially on SerialIn
'   and put next characters into led and stat
 
    SERIN serialin,T2400,["a"],lednr,stat 'serial data in on GPIO.0
   
    debug "Led number = ",dec LedNr,"  State = ",dec stat, $0D,$0A
    ' Led Nr = 0
    IF LedNr =  48  THEN outr1 ' if request is for LED#1 then goto led#1 routine
    'IF LedNr =  49  THEN outr2 ' if request is for LED#2 then goto led#2 routine
 
GOTO loop1
 
outr1:
    IF stat = 49 THEN high1 ' If status request is I/O pin#0 logic 1 [high]
    pause 50
    Ledout = 0
    GOTO loop1       ' then make I/O pin#0 high, else make it [low]
 
high1:
 
    pause 50
    Ledout = 1
    GOTO loop1   ' Make I/O pin#0 logic 1 [high]
 
end