Soldering station

[fratello]

I wrote this :

if w1 < (calibra - 3) then pwm mosfet 155, 250 
if w1 < (calibra - 1) then pwm mosfet 100, 200

but the heating start ONLY when w1 < (calibra - 3) !
Why don't start when w1 < (calibra - 1) ?!?

[Ioannis]

And what is the value of w1 then?

Ioannis

[fratello]

Example : if calibra (value for memory, set by user) is 140, the heating start at 137.
I wrote the routine for display those two values : w1 (current temperature) and calibra. The led blink ( PWM out) only when w1 < ( (calibra-3) !

if mode = 2 then
 call poz
 char = 16
 call    PrintChar  
 calibra = vt
                LcdReg  =  %10000000 + 25        ' cursor  X
                call    PrintCtrlLcd
                LcdReg  =  %01000011 + 1         ' cursor  Y
                call    PrintCtrlLcd
'~~~~~~~~~~~~~~~~~ now display results 
 if (vt dig 2) <1 then
                char = 16  
                call Printchar
                else         
                Char = (vt dig 2)            
                call    PrintChar 
 endif      


                Char = (vt dig 1)           
                call    PrintChar                     
 
                Char = (vt dig 0)           
                call    PrintChar

                Char = 16                 
                call    PrintChar
            
                Char = 13
                call  PrintChar
               
                Char = 14
                call  PrintChar

                Char = 16                 
                call    PrintChar

                Char = 15                 
                call    PrintChar
endif

[SKOLS1]

Fratello,can you make a code with MAX6675 thermocouple cold junction sensor?I have one,so I want to use it.

[fratello]

Hi! Why don't You write your own code ?!

[Byte_Butcher]

Fratello,can you make a code with MAX6675 thermocouple cold junction sensor?I have one,so I want to use it.

Here, I'm familiar with the MAX6675 so I'll give you a start...

This should read the MAX6675 and display degrees C & degrees F on a LCD display.
(Pin aliases for LCD not shown, only for the MAX6675)

'Alias pins - MAX6675 temp sensor
MXSCLK      var     PORTD.0   'MAX6675 Clock
MXCS        var     PORTD.2   'MAX6675 Chip Select
MXSO        Var     PORTD.3   'MAX6675 Serial Data

'--Variables-----------------------
kTemp       var     word    'raw data from MAX6675
tempC       var     word    'temperature in degrees C
tempF       var     word    'temp C converted to degrees F


'-----------Read and display temperature from MAX6675-----------
main:
    LOW MXCS                            'chip select low
    shiftin MXSO, MXSCLK, 0, [kTemp\16] 'shift in the data
    HIGH MXCS                           'chip select high
    tempC = kTemp >> 5                  'side shift to ditch the stuff to the right of the decimal point and just show whole degrees)  
    tempF = ((tempC * 18)/10) + 32      'convert C to F
        
   lcdout $fe,1,dec tempC," degrees C  ",$fe,$c0,dec tempF," degrees F  "   'display the data on LCD

   pause 500
   goto main
  
end

[fratello]

So it's possible to write code for 16F628A (16F648A), for example...since 12F675 don't have enough ports. And working with large fonts (if using Nokia LCD disply) , memory, pre-setting, etc...